On 12/10/15 20:19, Tony Lindgren wrote:
> * Ben Dooks <ben.dooks@xxxxxxxxxxxxxxx> [151012 11:22]:
>> On 12/10/15 18:45, Tony Lindgren wrote:
>>> * Ben Dooks <ben.dooks@xxxxxxxxxxxxxxx> [151012 10:38]:
>>>> The AM3715 OHCI controller will not function without the EHCI
>>>> unit's 120m fclk being enabled. If all the ports in the system
>>>> are set to OHCI then the 120m_fclk will not get enabled and no
>>>> devices are detected.
>>>>
>>>> Add a new (optional) property to signal the system must enable
>>>> the 120m_fck for OHCI so that if no EHCI ports are signalled
>>>> then the 120m_fclk should be enabled.
>>>>
>>>> We have found no information about why this is necessary, but
>>>> it is suspected the EHCI controller does not complete the initial
>>>> reset sequence and therefore does not hand control of the USB
>>>> port back.
>>>>
>>>> Signed-off-by: Ben Dooks <ben.dooks@xxxxxxxxxxxxxxx>
>>>> ---
>>>> Documentation/devicetree/bindings/usb/omap-usb.txt | 3 +++
>>>> drivers/mfd/omap-usb-host.c | 4 ++++
>>>> 2 files changed, 7 insertions(+)
>>>>
>>>> diff --git a/Documentation/devicetree/bindings/usb/omap-usb.txt b/Documentation/devicetree/bindings/usb/omap-usb.txt
>>>> index 38d9bb8..fb5fea5 100644
>>>> --- a/Documentation/devicetree/bindings/usb/omap-usb.txt
>>>> +++ b/Documentation/devicetree/bindings/usb/omap-usb.txt
>>>> @@ -23,6 +23,9 @@ OMAP MUSB GLUE
>>>> Optional properties:
>>>> - ctrl-module : phandle of the control module this glue uses to write to
>>>> mailbox
>>>> + - ti,ohci-needs-120m-fck : bool, enable the 120m ehci clock even if just
>>>> + using ohci. Needed for AM3517 in OHCI only mode.
>>>> +
>>>>
>>>> SOC specific device node entry
>>>> usb_otg_hs: usb_otg_hs@4a0ab000 {
>>>> diff --git a/drivers/mfd/omap-usb-host.c b/drivers/mfd/omap-usb-host.c
>>>> index 1d924d1..13880cf 100644
>>>> --- a/drivers/mfd/omap-usb-host.c
>>>> +++ b/drivers/mfd/omap-usb-host.c
>>>> @@ -680,6 +680,10 @@ static int usbhs_omap_probe(struct platform_device *pdev)
>>>> need_logic_fck |= true;
>>>> }
>>>>
>>>> + /* The AM3517 requries the 120m-fck active to allow the OHCI to work */
>>>> + if (of_property_read_bool(dev->of_node, "ti,ohci-needs-120m-fck"))
>>>> + need_logic_fck |= true;
>>>> +
>>>> if (need_logic_fck) {
>>>> omap->ehci_logic_fck = devm_clk_get(dev,
>>>> "usbhost_120m_fck");
>>>
>>> Hmm why not just use the standard device tree clocks property and then do
>>> clk_get_rate() on the clock?
>>
>> I don't see that helps enabling the clock. The code decideds if
>> no EHCI ports in use that it doesn't need to enable the EHCI fclk.
>
> Right, you need to do clk_prepare_enable() in it first? :)
No, if that was the case the driver would never work for the EHCI case.
The issue is:
1) All ports on the system are set to OHCI
2) The omap-usb-host.c does not touch usbhost_120m_fck if no EHCI ports
3) The OHCI fails to detect any devices due to point 2.
--
Ben Dooks http://www.codethink.co.uk/
Senior Engineer Codethink - Providing Genius
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
