[adding Ulf and Tomeu to cc list]
On Fri, Sep 18, 2015 at 10:27 PM, Tony Lindgren <tony@xxxxxxxxxxx> wrote:
> * Tony Lindgren <tony@xxxxxxxxxxx> [150918 10:54]:
>> * Javier Martinez Canillas <javier@xxxxxxxxxxxx> [150918 10:39]:
>> > Hello Tony,
>> >
>> > [snip]
>> >
>> > >
>> > > + vmmcsdio_fixed: fixedregulator-mmcsdio {
>> > > + compatible = "regulator-fixed";
>> > > + regulator-name = "vmmcsdio_fixed";
>> > > + regulator-min-microvolt = <1800000>;
>> > > + regulator-max-microvolt = <1800000>;
>> > > + gpio = <&gpio5 12 GPIO_ACTIVE_HIGH>; /* gpio140 WLAN_EN */
>> >
>> > I know that other OMAP boards use a fake fixed regulator to toggle the
>> > WiFi enable pin but now the MMC subsystem has proper support for power
>> > sequence providers so that should be used instead. For simple uses
>> > like this, Documentation/devicetree/bindings/mmc/mmc-pwrseq-simple.txt
>> > should be enough.
>>
>> Hmm OK great, I'll take a look. Looks like that might also provide a
>> nice solution for handling the 32k clock from palmas to the wl12xx.
>
> It seems it's not quite working yet.. It seems pwrseq_simple.c can't
> deal with delay on a power pin. It might be best to treat those using
> the regulator framework because of the refcounting and start-up delay.
Yes, pwrseq_simple does not support delaying a power pin. IIRC Tomeu
wanted to add a delay for power / reset pins at some point but then
the SDIO device he wanted to power up didn't need it so he dropped
that change at the end. I may be missremembering though.
> I don't think also having regulator handling in pwrseq_simple.c
> conflicts with the MMC regulators as they can be separate?
>
The original "mmc: add support for power-on sequencing through DT" [0]
patch from Olof that added just properties to the MMC controller slot
dev node had a "card-external-vcc-supply" for SDIO devices that needed
an external supply separate to vqmmc and vmmc supplies. The
pwrseq_simple does not support having an input supply regulator right
now but one can be added if that is needed.
> Also not related to wl12xx, the power pin on mwifiex_sdio 8787 wlan
> must be asserted low while reset is asserted and must stay low for
> 300ms after power pin has deasserted. Again using a regulator there
> for the power pin might make more sense.
>
Interesting, I've a patch queued on my tree to convert pwrseq_simple
to use the GPIO descriptors array API since all the code do now is to
set GPIO levels high or low for all the pins at the same time. But for
such a fine grained timing control as you said, I wonder if we should
just keep the code as it is now. Even when is open coding what
gpiod_{get,set,put}_array already do, it may make sense if we add
assert and deassert delay time for each pin.
Or maybe such a HW should have its own power sequence provider instead
of making pwrseq_simple more and more complex?
> Then getting the 32k clock from palmas is not working either, it
> seems some better deferred probe handling is needed there if
> omap_hsmmc is built-in and palmas-clk is a loadable module.
>
IIUC from another email, you already solved this.
> I think for the fix I'll stick with regulator fixed, let's update
> it later on unless you have better suggestions.
>
Yes, I didn't want to block your fixed regulator approach. I was just
pointing out that the MMC infrastructure already has support for power
sequence providers but if what is there doesn't fit your use case, I
agree that we can go with the regulator fixed for now and then change
it later.
>
> Cheers,
>
> Tony
[0]: http://patchwork.ozlabs.org/patch/312444/
Best regards,
Javier
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
