On Sat, Mar 14, 2009 at 7:00 PM, David Brownell <david-b@xxxxxxxxxxx> wrote: >> I don't get the warning now, but mmc0 is still broken (boot log below) > > Works for me, and I think you've got all the patches that > should matter. This is against today's GIT, yes? > Does taking #3 away help? Yes, this is against today's top of tree (a504a838e680d623745d3ad9cee1405ddbc4cbf9). I've rebuilt without patch 3 -- same result (boot log attached below). Is there any chance I might be missing some new kconfig option? I didn't notice any patches changing defconfig. >> OMAP3430 ES2.1 > > I hear ES3.1 will have better-working EHCI. ;) I get the crufty old protos to work with :-) >> sdhci: Secure Digital Host Controller Interface driver >> sdhci: Copyright(c) Pierre Ossman > > Why do you have SDHCI configured?? Damn good question! I have no idea when that snuck in there! It is removed in the new build. > Which slot reports that mmc_rescan() thing though? I take > it that's your diagnostic. More important ... why are you > only getting one such message? I hope you really *do* have > an uSD card in that slot. ;) Yes, there is a uSD card in the slot :-) U-boot and uImage are loading from the card so I know it is there! That is my diagnostic left over from trying to track down the SDIO issue. Why we only see one message is a good question. I would also expect to see two. > Try sticking diagnostics where it's checking whether there > is a card in the slot. And then where it turns on the > regulator for mmc0 ... I'm thinking the latter doesn't seem > to be happening, OK, will get another build going with those diagnostics. >> Waiting for root device /dev/mmcblk0p2... >> mmc1: new SDIO card at address 0001 >> > At that point I get: > > Waiting for root device /dev/mmcblk0p2... > mmc0: host does not support reading read-only switch. assuming write-enable. > mmc0: new high speed SD card at address 3395 > mmcblk0: mmc0:3395 SD02G 1.83 GiB > mmcblk0: p1 p2 > mmc1: voltage mask 100000 (orig ff8000, use 100000) > usb 2-1: new high speed USB device using musb_hdrc and address 2 > mmc1: new SDIO card at address 0001 > libertas_sdio mmc1:0001:1: firmware: using built-in firmware sd8686_helper.bin > libertas_sdio mmc1:0001:1: firmware: using built-in firmware sd8686.bin That is what I used to see too. Thanks for helping me track this down! Steve Linux version 2.6.29-rc8-omap1 (sakoman@tera) (gcc version 4.3.1 (GCC) ) #1 Sat Mar 14 20:36:14 PDT 2009 CPU: ARMv7 Processor [411fc082] revision 2 (ARMv7), cr=10c5387f CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache Machine: Gumstix Overo omapfb_early_vram, 12582912, 0x0 Memory policy: ECC disabled, Data cache writeback OMAP3430 ES2.1 SRAM: Mapped pa 0x40200000 to va 0xd7000000 size: 0x100000 Reserving 12582912 bytes SDRAM for VRAM Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024 Kernel command line: console=ttyS2,115200n8 vram=12M omapfb.mode=dvi:1024x768MR-16@60 omapfb.debug=y omapdss.def_disp=dvi root=/dev/mmcblk0p2 rw rootfstype=ext3 rootwait Clocking rate (Crystal/DPLL/ARM core): 26.0/331/500 MHz GPMC revision 5.0 IRQ: Found an INTC at 0xd8200000 (revision 4.0) with 96 interrupts Total of 96 interrupts on 1 active controller OMAP34xx GPIO hardware version 2.5 PID hash table entries: 1024 (order: 10, 4096 bytes) OMAP clockevent source: GPTIMER1 at 32768 Hz Console: colour dummy device 80x30 Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) Memory: 128MB 128MB = 256MB total Memory: 241408KB available (4460K code, 531K data, 936K init) Calibrating delay loop... 499.92 BogoMIPS (lpj=1949696) Mount-cache hash table entries: 512 CPU: Testing write buffer coherency: ok net_namespace: 764 bytes regulator: core version 0.5 NET: Registered protocol family 16 Found NAND on CS0 Registering NAND on CS0 OMAP DMA hardware revision 4.0 bio: create slab <bio-0> at 0 OMAP DSS rev 2.0 OMAP DISPC rev 3.0 OMAP VENC rev 2 i2c_omap i2c_omap.1: bus 1 rev3.12 at 2600 kHz twl4030: PIH (irq 7) chaining IRQs 368..375 twl4030: power (irq 373) chaining IRQs 376..383 twl4030: gpio (irq 368) chaining IRQs 384..401 set_machine_constraints: disable 'VMMC1' --> 0 regulator: VMMC1: 1850 <--> 3150 mV normal standby set_machine_constraints: disable 'VUSB1V5' --> 0 regulator: VUSB1V5: 1500 <--> 0 mV normal standby set_machine_constraints: disable 'VUSB1V8' --> 0 regulator: VUSB1V8: 1800 <--> 0 mV normal standby set_machine_constraints: disable 'VUSB3V1' --> 0 regulator: VUSB3V1: 3100 <--> 0 mV normal standby i2c_omap i2c_omap.3: bus 3 rev3.12 at 400 kHz SCSI subsystem initialized twl4030_usb twl4030_usb: Initialized TWL4030 USB module usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb Bluetooth: Core ver 2.14 NET: Registered protocol family 31 Bluetooth: HCI device and connection manager initialized Bluetooth: HCI socket layer initialized cfg80211: Using static regulatory domain info cfg80211: Regulatory domain: US (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) (2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2700 mBm) (5170000 KHz - 5190000 KHz @ 40000 KHz), (600 mBi, 2300 mBm) (5190000 KHz - 5210000 KHz @ 40000 KHz), (600 mBi, 2300 mBm) (5210000 KHz - 5230000 KHz @ 40000 KHz), (600 mBi, 2300 mBm) (5230000 KHz - 5330000 KHz @ 40000 KHz), (600 mBi, 2300 mBm) (5735000 KHz - 5835000 KHz @ 40000 KHz), (600 mBi, 3000 mBm) cfg80211: Calling CRDA for country: US musb_hdrc: version 6.0, musb-dma, host, debug=0 musb_hdrc: USB Host mode controller at d80ab000 using DMA, IRQ 92 musb_hdrc musb_hdrc: MUSB HDRC host driver musb_hdrc musb_hdrc: new USB bus registered, assigned bus number 1 usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb1: Product: MUSB HDRC host driver usb usb1: Manufacturer: Linux 2.6.29-rc8-omap1 musb-hcd usb usb1: SerialNumber: musb_hdrc usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected NET: Registered protocol family 2 IP route cache hash table entries: 2048 (order: 1, 8192 bytes) TCP established hash table entries: 8192 (order: 4, 65536 bytes) TCP bind hash table entries: 8192 (order: 3, 32768 bytes) TCP: Hash tables configured (established 8192 bind 8192) TCP reno registered NET: Registered protocol family 1 VFS: Disk quotas dquot_6.5.2 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) JFFS2 version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. msgmni has been set to 471 alg: No test for stdrng (krng) io scheduler noop registered io scheduler anticipatory registered (default) io scheduler deadline registered io scheduler cfq registered Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled serial8250.0: ttyS0 at MMIO 0x4806a000 (irq = 72) is a ST16654 serial8250.0: ttyS1 at MMIO 0x4806c000 (irq = 73) is a ST16654 serial8250.0: ttyS2 at MMIO 0x49020000 (irq = 74) is a ST16654 console [ttyS2] enabled brd: module loaded loop: module loaded usbcore: registered new interface driver asix usbcore: registered new interface driver cdc_ether i2c /dev entries driver Driver 'sd' needs updating - please use bus_type methods omap2-nand driver initializing NAND device: Manufacturer ID: 0x2c, Chip ID: 0xba (Micron NAND 256MiB 1,8V 16-bit) cmdlinepart partition parsing not available Creating 5 MTD partitions on "omap2-nand": 0x000000000000-0x000000080000 : "xloader" 0x000000080000-0x000000240000 : "uboot" 0x000000240000-0x000000280000 : "uboot environment" 0x000000280000-0x000000680000 : "linux" 0x000000680000-0x000010000000 : "rootfs" ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver ehci-omap ehci-omap.0: OMAP-EHCI Host Controller ehci-omap ehci-omap.0: new USB bus registered, assigned bus number 2 ehci-omap ehci-omap.0: irq 77, io mem 0x48064800 ehci-omap ehci-omap.0: USB 2.0 started, EHCI 1.00 usb usb2: New USB device found, idVendor=1d6b, idProduct=0002 usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb2: Product: OMAP-EHCI Host Controller usb usb2: Manufacturer: Linux 2.6.29-rc8-omap1 ehci_hcd usb usb2: SerialNumber: ehci-omap.0 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 3 ports detected Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. udc: OMAP UDC driver, version: 4 October 2004 (iso) (dma) mice: PS/2 mouse device common for all mice twl4030_rtc twl4030_rtc: rtc core: registered twl4030_rtc as rtc0 OMAP Watchdog Timer Rev 0x31: initial timeout 60 sec Bluetooth: HCI UART driver ver 2.2 Bluetooth: HCI H4 protocol initialized Bluetooth: HCI BCSP protocol initialized Bluetooth: Broadcom Blutonium firmware driver ver 1.2 usbcore: registered new interface driver bcm203x Bluetooth: Digianswer Bluetooth USB driver ver 0.10 usbcore: registered new interface driver bpa10x mmci-omap-hs mmci-omap-hs.0: Failed to get debounce clock regulator: Unable to get requested regulator: vmmc_aux mmci-omap-hs mmci-omap-hs.1: Failed to get debounce clock regulator: Unable to get requested regulator: vmmc mmc_rescan: card ocr from io_op=0x90ff8000, err = 0 usbcore: registered new interface driver usbhid usbhid: v2.6:USB HID core driver Advanced Linux Sound Architecture Driver Version 1.0.18a. usbcore: registered new interface driver snd-usb-audio No device for DAI twl4030 No device for DAI omap-mcbsp-dai-0 No device for DAI omap-mcbsp-dai-1 No device for DAI omap-mcbsp-dai-2 No device for DAI omap-mcbsp-dai-3 No device for DAI omap-mcbsp-dai-4 overo SoC init TWL4030 Audio Codec init asoc: twl4030 <-> omap-mcbsp-dai-0 mapping ok ALSA device list: #0: overo (twl4030) oprofile: using arm/armv7 TCP cubic registered NET: Registered protocol family 17 NET: Registered protocol family 15 Bluetooth: L2CAP ver 2.11 Bluetooth: L2CAP socket layer initialized Bluetooth: SCO (Voice Link) ver 0.6 Bluetooth: SCO socket layer initialized Bluetooth: RFCOMM socket layer initialized Bluetooth: RFCOMM TTY layer initialized Bluetooth: RFCOMM ver 1.10 Bluetooth: BNEP (Ethernet Emulation) ver 1.3 Bluetooth: BNEP filters: protocol multicast Bluetooth: HIDP (Human Interface Emulation) ver 1.2 RPC: Registered udp transport module. RPC: Registered tcp transport module. ThumbEE CPU extension supported. Power Management for TI OMAP3. SmartReflex driver initialized VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 1 fbcvt: 1024x768@60: CVT Name - .786M3-R Console: switching to colour frame buffer device 128x48 clock: clksel_round_rate_div: dpll4_m4_ck target_rate 86400000 clock: new_div = 5, new_rate = 86400000 twl4030_rtc twl4030_rtc: setting system clock to 2000-01-01 00:12:36 UTC (946685556) Waiting for root device /dev/mmcblk0p2... mmc1: new SDIO card at address 0001 -- To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
