phyCORE-AM335x is a SoM (System on Module) containing
a AM335x SOC. The module can be connected to different
carrier boards.
Some hardware parts are configurable on the phyCORE-AM335x.
So they are disabled on default in this som dtsi file.
They will be enabled in the board dts files, when populated.
* RAM up to 1GiB
* PMIC
* NAND flash up to 1GiB
* Eth PHY on SOM: 1x RMII
* SPI NOR flash 8MiB (optional)
* i2c RTC (optional)
* i2c EEPROM 4kiB (optional)
Signed-off-by: Teresa Remmet <t.remmet@xxxxxxxxx>
---
arch/arm/boot/dts/am335x-phycore-som.dtsi | 368 ++++++++++++++++++++++++++++++
1 file changed, 368 insertions(+)
create mode 100644 arch/arm/boot/dts/am335x-phycore-som.dtsi
diff --git a/arch/arm/boot/dts/am335x-phycore-som.dtsi b/arch/arm/boot/dts/am335x-phycore-som.dtsi
new file mode 100644
index 0000000..4d28fc3
--- /dev/null
+++ b/arch/arm/boot/dts/am335x-phycore-som.dtsi
@@ -0,0 +1,368 @@
+/*
+ * Copyright (C) 2015 Phytec Messtechnik GmbH
+ * Author: Teresa Remmet <t.remmet@xxxxxxxxx>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include "am33xx.dtsi"
+
+/ {
+ model = "Phytec AM335x phyCORE";
+ compatible = "phytec,am335x-phycore-som", "ti,am33xx";
+
+ aliases {
+ rtc0 = &i2c_rtc;
+ rtc1 = &rtc;
+ };
+
+ cpus {
+ cpu@0 {
+ cpu0-supply = <&vdd1_reg>;
+ };
+ };
+
+ memory {
+ device_type = "memory";
+ reg = <0x80000000 0x10000000>; /* 256 MB */
+ };
+
+ vbat: fixedregulator@0 {
+ compatible = "regulator-fixed";
+ };
+};
+
+/* Crypto Module */
+&aes {
+ status = "okay";
+};
+
+&sham {
+ status = "okay";
+};
+
+/* Ethernet */
+&am33xx_pinmux {
+ ethernet0_pins: pinmux_ethernet0 {
+ pinctrl-single,pins = <
+ 0x10c (PIN_INPUT_PULLDOWN | MUX_MODE1) /* mii1_crs.rmii1_crs_dv */
+ 0x110 (PIN_INPUT_PULLDOWN | MUX_MODE1) /* mii1_rxerr.rmii1_rxerr */
+ 0x114 (PIN_OUTPUT | MUX_MODE1) /* mii1_txen.rmii1_txen */
+ 0x124 (PIN_OUTPUT | MUX_MODE1) /* mii1_txd1.rmii1_txd1 */
+ 0x128 (PIN_OUTPUT | MUX_MODE1) /* mii1_txd0.rmii1_txd0 */
+ 0x13c (PIN_INPUT_PULLDOWN | MUX_MODE1) /* mii1_rxd1.rmii1_rxd1 */
+ 0x140 (PIN_INPUT_PULLDOWN | MUX_MODE1) /* mii1_rxd0.rmii1_rxd0 */
+ 0x144 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* rmii1_refclk.rmii1_refclk */
+ >;
+ };
+
+ mdio_pins: pinmux_mdio {
+ pinctrl-single,pins = <
+ /* MDIO */
+ 0x148 (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0) /* mdio_data.mdio_data */
+ 0x14c (PIN_OUTPUT_PULLUP | MUX_MODE0) /* mdio_clk.mdio_clk */
+ >;
+ };
+};
+
+&cpsw_emac0 {
+ phy_id = <&davinci_mdio>, <0>;
+ phy-mode = "rmii";
+ dual_emac_res_vlan = <1>;
+};
+
+&davinci_mdio {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mdio_pins>;
+ status = "okay";
+};
+
+&mac {
+ slaves = <1>;
+ pinctrl-names = "default";
+ pinctrl-0 = <ðernet0_pins>;
+ status = "okay";
+};
+
+&phy_sel {
+ rmii-clock-ext;
+};
+
+/* I2C Busses */
+&am33xx_pinmux {
+ i2c0_pins: pinmux_i2c0 {
+ pinctrl-single,pins = <
+ 0x188 (PIN_INPUT | MUX_MODE0) /* i2c0_sda.i2c0_sda */
+ 0x18c (PIN_INPUT | MUX_MODE0) /* i2c0_scl.i2c0_scl */
+ >;
+ };
+};
+
+&i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins>;
+ clock-frequency = <400000>;
+ status = "okay";
+
+ tps: pmic@2d {
+ reg = <0x2d>;
+ };
+
+ i2c_eeprom: eeprom@52 {
+ compatible = "atmel,24c32";
+ pagesize = <32>;
+ reg = <0x52>;
+ status = "disabled";
+ };
+
+ i2c_rtc: rtc@68 {
+ compatible = "rv4162";
+ reg = <0x68>;
+ status = "disabled";
+ };
+};
+
+/* NAND memory */
+&am33xx_pinmux {
+ nandflash_pins: pinmux_nandflash {
+ pinctrl-single,pins = <
+ 0x0 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad0.gpmc_ad0 */
+ 0x4 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad1.gpmc_ad1 */
+ 0x8 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad2.gpmc_ad2 */
+ 0xc (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad3.gpmc_ad3 */
+ 0x10 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad4.gpmc_ad4 */
+ 0x14 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad5.gpmc_ad5 */
+ 0x18 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad6.gpmc_ad6 */
+ 0x1c (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad7.gpmc_ad7 */
+ 0x70 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_wait0.gpmc_wait0 */
+ 0x7c (PIN_OUTPUT | MUX_MODE0) /* gpmc_csn0.gpmc_csn0 */
+ 0x90 (PIN_OUTPUT | MUX_MODE0) /* gpmc_advn_ale.gpmc_advn_ale */
+ 0x94 (PIN_OUTPUT | MUX_MODE0) /* gpmc_oen_ren.gpmc_oen_ren */
+ 0x98 (PIN_OUTPUT | MUX_MODE0) /* gpmc_wen.gpmc_wen */
+ 0x9c (PIN_OUTPUT | MUX_MODE0) /* gpmc_be0n_cle.gpmc_be0n_cle */
+ >;
+ };
+};
+
+&elm {
+ status = "okay";
+};
+
+&gpmc {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&nandflash_pins>;
+ ranges = <0 0 0x08000000 0x1000000>; /* CS0: NAND */
+ nandflash: nand@0,0 {
+ reg = <0 0 4>; /* CS0, offset 0, IO size 4 */
+ nand-bus-width = <8>;
+ ti,nand-ecc-opt = "bch8";
+ gpmc,device-nand = "true";
+ gpmc,device-width = <1>;
+ gpmc,sync-clk-ps = <0>;
+ gpmc,cs-on-ns = <0>;
+ gpmc,cs-rd-off-ns = <30>;
+ gpmc,cs-wr-off-ns = <30>;
+ gpmc,adv-on-ns = <0>;
+ gpmc,adv-rd-off-ns = <30>;
+ gpmc,adv-wr-off-ns = <30>;
+ gpmc,we-on-ns = <0>;
+ gpmc,we-off-ns = <20>;
+ gpmc,oe-on-ns = <10>;
+ gpmc,oe-off-ns = <30>;
+ gpmc,access-ns = <30>;
+ gpmc,rd-cycle-ns = <30>;
+ gpmc,wr-cycle-ns = <30>;
+ gpmc,wait-on-read = "true";
+ gpmc,wait-on-write = "true";
+ gpmc,bus-turnaround-ns = <0>;
+ gpmc,cycle2cycle-delay-ns = <50>;
+ gpmc,cycle2cycle-diffcsen;
+ gpmc,clk-activation-ns = <0>;
+ gpmc,wait-monitoring-ns = <0>;
+ gpmc,wr-access-ns = <30>;
+ gpmc,wr-data-mux-bus-ns = <0>;
+
+ elm_id = <&elm>;
+
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "xload";
+ reg = <0x0 0x20000>;
+ };
+ partition@1 {
+ label = "xload_backup1";
+ reg = <0x20000 0x20000>;
+ };
+ partition@2 {
+ label = "xload_backup2";
+ reg = <0x40000 0x20000>;
+ };
+ partition@3 {
+ label = "xload_backup3";
+ reg = <0x60000 0x20000>;
+ };
+ partition@4 {
+ label = "barebox";
+ reg = <0x80000 0x80000>;
+ };
+ partition@5 {
+ label = "bareboxenv";
+ reg = <0x100000 0x40000>;
+ };
+ partition@6 {
+ label = "oftree";
+ reg = <0x140000 0x40000>;
+ };
+ partition@7 {
+ label = "kernel";
+ reg = <0x180000 0x800000>;
+ };
+ partition@8 {
+ label = "root";
+ reg = <0x980000 0x0>;
+ };
+ };
+};
+
+/* Power */
+#include "tps65910.dtsi"
+
+&tps {
+ vcc1-supply = <&vbat>;
+ vcc2-supply = <&vbat>;
+ vcc3-supply = <&vbat>;
+ vcc4-supply = <&vbat>;
+ vcc5-supply = <&vbat>;
+ vcc6-supply = <&vbat>;
+ vcc7-supply = <&vbat>;
+ vccio-supply = <&vbat>;
+
+ regulators {
+ vrtc_reg: regulator@0 {
+ regulator-always-on;
+ };
+
+ vio_reg: regulator@1 {
+ regulator-always-on;
+ };
+
+ vdd1_reg: regulator@2 {
+ /* VDD_MPU voltage limits 0.95V - 1.26V with +/-4% tolerance */
+ regulator-name = "vdd_mpu";
+ regulator-min-microvolt = <912500>;
+ regulator-max-microvolt = <1312500>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vdd2_reg: regulator@3 {
+ /* VDD_CORE voltage limits 0.95V - 1.1V with +/-4% tolerance */
+ regulator-name = "vdd_core";
+ regulator-min-microvolt = <912500>;
+ regulator-max-microvolt = <1150000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vdd3_reg: regulator@4 {
+ regulator-always-on;
+ };
+
+ vdig1_reg: regulator@5 {
+ regulator-name = "vdig1_1p8v";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ vdig2_reg: regulator@6 {
+ regulator-always-on;
+ };
+
+ vpll_reg: regulator@7 {
+ regulator-always-on;
+ };
+
+ vdac_reg: regulator@8 {
+ regulator-always-on;
+ };
+
+ vaux1_reg: regulator@9 {
+ regulator-always-on;
+ };
+
+ vaux2_reg: regulator@10 {
+ regulator-always-on;
+ };
+
+ vaux33_reg: regulator@11 {
+ regulator-always-on;
+ };
+
+ vmmc_reg: regulator@12 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+ };
+};
+
+&vbat {
+ regulator-name = "vbat";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-boot-on;
+};
+
+/* SPI Busses */
+&am33xx_pinmux {
+ spi0_pins: pinmux_spi0 {
+ pinctrl-single,pins = <
+ 0x150 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* spi0_clk.spi0_clk */
+ 0x154 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* spi0_d0.spi0_d0 */
+ 0x158 (PIN_INPUT_PULLUP | MUX_MODE0) /* spi0_d1.spi0_d1 */
+ 0x15c (PIN_INPUT_PULLUP | MUX_MODE0) /* spi0_cs0.spi0_cs0 */
+ >;
+ };
+};
+
+&spi0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi0_pins>;
+ status = "okay";
+
+ serial_flash: m25p80@0 {
+ compatible = "m25p80";
+ spi-max-frequency = <48000000>;
+ reg = <0x0>;
+ m25p,fast-read;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "xload";
+ reg = <0x0 0x20000>;
+ };
+ partition@1 {
+ label = "barebox";
+ reg = <0x20000 0x80000>;
+ };
+ partition@2 {
+ label = "bareboxenv";
+ reg = <0xa0000 0x20000>;
+ };
+ partition@3 {
+ label = "oftree";
+ reg = <0xc0000 0x20000>;
+ };
+ partition@4 {
+ label = "kernel";
+ reg = <0xe0000 0x0>;
+ };
+ };
+};
--
1.9.1
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
