Hi Eyal,
On 04/30/2015 05:15 AM, Eyal Reizer wrote:
> enable mmc3 used for wlan and uart3 used for bluetooth
>
> configure the gpios used for wlan and bluetooth controls
>
> add fixed voltage regulator used for wlan power control
>
> Configure shared transport support for uart3
>
> Signed-off-by: Eyal Reizer <eyalr@xxxxxx>
> ---
> arch/arm/boot/dts/am437x-gp-evm.dts | 114 ++++++++++++++++++++++++++++++++++
> include/dt-bindings/pinctrl/am43xx.h | 1 +
> 2 files changed, 115 insertions(+)
>
> diff --git a/arch/arm/boot/dts/am437x-gp-evm.dts b/arch/arm/boot/dts/am437x-gp-evm.dts
> index 26956cb..2b2f715 100644
> --- a/arch/arm/boot/dts/am437x-gp-evm.dts
> +++ b/arch/arm/boot/dts/am437x-gp-evm.dts
> @@ -21,6 +21,7 @@
>
> aliases {
> display0 = &lcd0;
> + serial3 = &uart3;
> };
>
> vmmcsd_fixed: fixedregulator-sd {
> @@ -42,6 +43,15 @@
> gpio = <&gpio5 7 GPIO_ACTIVE_HIGH>;
> };
>
> + vmmcwl_fixed: fixedregulator-mmcwl {
> + compatible = "regulator-fixed";
> + regulator-name = "vmmcwl_fixed";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + gpio = <&gpio1 20 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + };
> +
> backlight {
> compatible = "pwm-backlight";
> pwms = <&ecap0 0 50000 PWM_POLARITY_INVERTED>;
> @@ -106,9 +116,25 @@
> };
> };
> };
> +
> + kim {
> + compatible = "kim";
> + nshutdown_gpio = <48>; /* Bank1, pin16 */
> + dev_name = "/dev/ttyS3";
> + flow_cntrl = <1>;
> + baud_rate = <3000000>;
> + };
> +
> + btwilink {
> + compatible = "btwilink";
> + };
I'd really like to see TI working _with_ the Linux kernel
bluetooth stack, rather than working *around* it.
The st_kim driver is really a mess, and wilink8 has
no other channels but BT, which the hci_ll BT protocol
driver already handles.
> };
>
> &am43xx_pinmux {
> + pinctrl-names = "default", "sleep";
> + pinctrl-0 = <&wlan_pins_default>;
> + pinctrl-1 = <&wlan_pins_sleep>;
> +
> i2c0_pins: i2c0_pins {
> pinctrl-single,pins = <
> 0x188 (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0) /* i2c0_sda.i2c0_sda */
> @@ -340,6 +366,53 @@
> 0x204 (DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7) /* cam1_data7 mode 0*/
> >;
> };
> +
> + mmc3_pins_default: pinmux_mmc3_pins_default {
> + pinctrl-single,pins = <
> + 0x8c (PIN_INPUT_PULLUP | MUX_MODE3) /* gpmc_clk.mmc2_clk */
> + 0x88 (PIN_INPUT_PULLUP | MUX_MODE3) /* gpmc_csn3.mmc2_cmd */
> + 0x44 (PIN_INPUT_PULLUP | MUX_MODE3) /* gpmc_a1.mmc2_dat0 */
> + 0x48 (PIN_INPUT_PULLUP | MUX_MODE3) /* gpmc_a2.mmc2_dat1 */
> + 0x4c (PIN_INPUT_PULLUP | MUX_MODE3) /* gpmc_a3.mmc2_dat2 */
> + 0x78 (PIN_INPUT_PULLUP | MUX_MODE3) /* gpmc_be1n.mmc2_dat3 */
> + >;
> + };
> +
> + mmc3_pins_sleep: pinmux_mmc3_pins_sleep {
> + pinctrl-single,pins = <
> + 0x8c (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_clk.mmc2_clk */
> + 0x88 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_csn3.mmc2_cmd */
> + 0x44 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_a1.mmc2_dat0 */
> + 0x48 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_a2.mmc2_dat1 */
> + 0x4c (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_a3.mmc2_dat2 */
> + 0x78 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_be1n.mmc2_dat3 */
> + >;
> + };
> +
> + wlan_pins_default: pinmux_wlan_pins_default {
> + pinctrl-single,pins = <
> + 0x50 (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_a4.gpio1_20 WL_EN */
> + 0x5c (PIN_INPUT | WAKEUP_ENABLE | MUX_MODE7) /* gpmc_a7.gpio1_23 WL_IRQ*/
> + 0x40 (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_a0.gpio1_16 BT_EN*/
> + >;
> + };
> +
> + wlan_pins_sleep: pinmux_wlan_pins_sleep {
> + pinctrl-single,pins = <
> + 0x50 (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_a4.gpio1_20 WL_EN */
> + 0x5c (PIN_INPUT | WAKEUP_ENABLE | MUX_MODE7) /* gpmc_a7.gpio1_23 WL_IRQ*/
> + 0x40 (PIN_OUTPUT_PULLUP | MUX_MODE7) /* gpmc_a0.gpio1_16 BT_EN*/
> + >;
> + };
> +
> + uart3_pins: uart3_pins {
> + pinctrl-single,pins = <
> + 0x228 (PIN_INPUT | MUX_MODE0) /* uart3_rxd.uart3_rxd */
> + 0x22c (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* uart3_txd.uart3_txd */
> + 0x230 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart3_ctsn.uart3_ctsn */
> + 0x234 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* uart3_rtsn.uart3_rtsn */
> + >;
> + };
> };
>
> &i2c0 {
> @@ -446,6 +519,10 @@
> status = "okay";
> };
>
> +&gpio1 {
> + status = "okay";
> +};
> +
> &gpio3 {
> status = "okay";
> };
> @@ -468,6 +545,43 @@
> cd-gpios = <&gpio0 6 GPIO_ACTIVE_HIGH>;
> };
>
> +&mmc3 {
> + status = "okay";
> + /* these are on the crossbar and are outlined in the
> + xbar-event-map element */
> + dmas = <&edma 30
> + &edma 31>;
> + dma-names = "tx", "rx";
> + vmmc-supply = <&vmmcwl_fixed>;
> + bus-width = <4>;
> + pinctrl-names = "default", "sleep";
> + pinctrl-0 = <&mmc3_pins_default>;
> + pinctrl-1 = <&mmc3_pins_sleep>;
So the wilink8 module is the only thing that can be plugged
into the camera header?
I think all this really needs to go into a DT overlay.
Regards,
Peter Hurley
> + cap-power-off-card;
> + keep-power-in-suspend;
> + ti,non-removable;
> +
> + #address-cells = <1>;
> + #size-cells = <0>;
> + wlcore: wlcore@0 {
> + compatible = "ti,wl1835";
> + reg = <2>;
> + interrupt-parent = <&gpio1>;
> + interrupts = <23 IRQ_TYPE_LEVEL_HIGH>;
> + };
> +};
> +
> +&edma {
> + ti,edma-xbar-event-map = /bits/ 16 <1 30
> + 2 31>;
> +};
> +
> +&uart3 {
> + status = "okay";
> + pinctrl-names = "default";
> + pinctrl-0 = <&uart3_pins>;
> +};
> +
> &usb2_phy1 {
> status = "okay";
> };
> diff --git a/include/dt-bindings/pinctrl/am43xx.h b/include/dt-bindings/pinctrl/am43xx.h
> index 5f4d0189..b00bbc9 100644
> --- a/include/dt-bindings/pinctrl/am43xx.h
> +++ b/include/dt-bindings/pinctrl/am43xx.h
> @@ -21,6 +21,7 @@
> #define SLEWCTRL_SLOW (1 << 19)
> #define SLEWCTRL_FAST 0
> #define DS0_PULL_UP_DOWN_EN (1 << 27)
> +#define WAKEUP_ENABLE (1 << 29)
>
> #define PIN_OUTPUT (PULL_DISABLE)
> #define PIN_OUTPUT_PULLUP (PULL_UP)
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
