Re: [alsa-devel] Patches to bind the SGTL5000 chip to AM33XX McASP

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On 03/19/2015 08:06 PM, Nikolay Dimitrov wrote:
> Slight clarification here - I can't find any such reference in the
> SGTL5000 datasheet where it's explicitly written that the I2C bus
> *requires* the MCLK running. Unfortunately, all of us found this
> obscure dependency empirically.

It is not spelled out as such, but in:
http://cache.freescale.com/files/analog/doc/data_sheet/SGTL5000.pdf?pspll=1
bottom of page9 (note 1) and the power up sequence in page10. See also page13,
RESET section.

>> If you change audio controls while you don't have audio activity, you will
>> still need to have the MCLK running.
> 
> Correct. And this is a big issue. As far as I know, the kernel drivers
> control separately the clock domains, and separately i2c devices, so
> the basic expectation on the kernel side is that there's no connection
> between these 2. In this specific case, because of the SGTL5000's
> implementation, there's a dependency. Right now as I see it, there are
> several ways to resolve it:
> 
> 1. Run the reference clock all the time, so the SGTL5000 codec is
> happy, and DAPM widgets can work as-is. We've been doing this all the
> time - the reference clocks are routinely configured either in the
> bootloader, or in the DTS iomuxc node. While this can work in some
> cases (or until someone touches the same clock or one of its parents
> :D), there are other cases (like battery-powered devices) where people
> would want more aggressive power management, which means controlling
> the reference clock at runtime (see #2).

Note the the codec driver will enable the clock and will not let it to be
turned off. You need to work on the codec driver to sort this out.

> 2. Add "hacks" in the DAPM widgets that add control to the codec's
> reference clocks. While this seems the preferred route to many, the
> general feeling is that such approach is not very welcome in upstream.

SND_SOC_DAPM_CLOCK_SUPPLY()

> 3. Add explicit support in the kernel's audio subsystem for
> dependencies between i2c devices and clocks, maybe via "DAPM clock
> widget" or something like this. Provided that the DAPM graphs are
> defined properly, this will work out-of-the-box for all use cases,
> without the hacks (until we see even more twisted cases).

This can be handled within the codec driver with some changes. If you have
external clock which can be enabled/diabled with a GPIO, then you can use
that. We already have binding for this type of external clocks (in
linux-next): look for "gpio-gate-clock"
You define your external GPIO controlled clock with this binding and use the
phandle in the codec driver.
Change the codec driver to enable/disable the clock when needed.
When you do not have audio activity, set the regmap to cache only so any
change in the controls will not reach the HW. When you power up next time the
regmap will sync the changes to the chip, so you will have the changes commited.

-- 
Péter
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html




[Index of Archives]     [Linux Arm (vger)]     [ARM Kernel]     [ARM MSM]     [Linux Tegra]     [Linux WPAN Networking]     [Linux Wireless Networking]     [Maemo Users]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Yosemite Trails]     [Linux Kernel]     [Linux SCSI]

  Powered by Linux