On 01/30/2015 06:02 PM, Jyri Sarha wrote:
> Disables GPIO support and LINE2 input and renames Mic3 input to Mic2,
> if tlv320aic3104 mode is seleced. Devicetree binding document is
> updated accordingly.
>
> Signed-off-by: Jyri Sarha <jsarha@xxxxxx>
> ---
> .../devicetree/bindings/sound/tlv320aic3x.txt | 10 +-
> sound/soc/codecs/tlv320aic3x.c | 344 ++++++++++++++------
> 2 files changed, 252 insertions(+), 102 deletions(-)
>
> diff --git a/Documentation/devicetree/bindings/sound/tlv320aic3x.txt b/Documentation/devicetree/bindings/sound/tlv320aic3x.txt
> index 5e6040c..47a213c 100644
> --- a/Documentation/devicetree/bindings/sound/tlv320aic3x.txt
> +++ b/Documentation/devicetree/bindings/sound/tlv320aic3x.txt
> @@ -9,6 +9,7 @@ Required properties:
> "ti,tlv320aic33" - TLV320AIC33
> "ti,tlv320aic3007" - TLV320AIC3007
> "ti,tlv320aic3106" - TLV320AIC3106
> + "ti,tlv320aic3104" - TLV320AIC3104
I think you should update the driver's tlv320aic3x_of_match[] table to include
the ti,tlv320aic3104 as well?
other than that it looks good.
--
Péter
>
>
> - reg - <int> - I2C slave address
> @@ -18,6 +19,7 @@ Optional properties:
>
> - gpio-reset - gpio pin number used for codec reset
> - ai3x-gpio-func - <array of 2 int> - AIC3X_GPIO1 & AIC3X_GPIO2 Functionality
> + - Not supported on tlv320aic3104
> - ai3x-micbias-vg - MicBias Voltage required.
> 1 - MICBIAS output is powered to 2.0V,
> 2 - MICBIAS output is powered to 2.5V,
> @@ -36,7 +38,13 @@ CODEC output pins:
> * HPLCOM
> * HPRCOM
>
> -CODEC input pins:
> +CODEC input pins for TLV320AIC3104:
> + * MIC2L
> + * MIC2R
> + * LINE1L
> + * LINE1R
> +
> +CODEC input pins for other compatible codecs:
> * MIC3L
> * MIC3R
> * LINE1L
> diff --git a/sound/soc/codecs/tlv320aic3x.c b/sound/soc/codecs/tlv320aic3x.c
> index b7ebce0..49ba3c7 100644
> --- a/sound/soc/codecs/tlv320aic3x.c
> +++ b/sound/soc/codecs/tlv320aic3x.c
> @@ -87,6 +87,7 @@ struct aic3x_priv {
> #define AIC3X_MODEL_3X 0
> #define AIC3X_MODEL_33 1
> #define AIC3X_MODEL_3007 2
> +#define AIC3X_MODEL_3104 3
> u16 model;
>
> /* Selects the micbias voltage */
> @@ -316,52 +317,37 @@ static const struct snd_kcontrol_new aic3x_snd_controls[] = {
> * only for swapped L-to-R and R-to-L routes. See below stereo controls
> * for direct L-to-L and R-to-R routes.
> */
> - SOC_SINGLE_TLV("Left Line Mixer Line2R Bypass Volume",
> - LINE2R_2_LLOPM_VOL, 0, 118, 1, output_stage_tlv),
> SOC_SINGLE_TLV("Left Line Mixer PGAR Bypass Volume",
> PGAR_2_LLOPM_VOL, 0, 118, 1, output_stage_tlv),
> SOC_SINGLE_TLV("Left Line Mixer DACR1 Playback Volume",
> DACR1_2_LLOPM_VOL, 0, 118, 1, output_stage_tlv),
>
> - SOC_SINGLE_TLV("Right Line Mixer Line2L Bypass Volume",
> - LINE2L_2_RLOPM_VOL, 0, 118, 1, output_stage_tlv),
> SOC_SINGLE_TLV("Right Line Mixer PGAL Bypass Volume",
> PGAL_2_RLOPM_VOL, 0, 118, 1, output_stage_tlv),
> SOC_SINGLE_TLV("Right Line Mixer DACL1 Playback Volume",
> DACL1_2_RLOPM_VOL, 0, 118, 1, output_stage_tlv),
>
> - SOC_SINGLE_TLV("Left HP Mixer Line2R Bypass Volume",
> - LINE2R_2_HPLOUT_VOL, 0, 118, 1, output_stage_tlv),
> SOC_SINGLE_TLV("Left HP Mixer PGAR Bypass Volume",
> PGAR_2_HPLOUT_VOL, 0, 118, 1, output_stage_tlv),
> SOC_SINGLE_TLV("Left HP Mixer DACR1 Playback Volume",
> DACR1_2_HPLOUT_VOL, 0, 118, 1, output_stage_tlv),
>
> - SOC_SINGLE_TLV("Right HP Mixer Line2L Bypass Volume",
> - LINE2L_2_HPROUT_VOL, 0, 118, 1, output_stage_tlv),
> SOC_SINGLE_TLV("Right HP Mixer PGAL Bypass Volume",
> PGAL_2_HPROUT_VOL, 0, 118, 1, output_stage_tlv),
> SOC_SINGLE_TLV("Right HP Mixer DACL1 Playback Volume",
> DACL1_2_HPROUT_VOL, 0, 118, 1, output_stage_tlv),
>
> - SOC_SINGLE_TLV("Left HPCOM Mixer Line2R Bypass Volume",
> - LINE2R_2_HPLCOM_VOL, 0, 118, 1, output_stage_tlv),
> SOC_SINGLE_TLV("Left HPCOM Mixer PGAR Bypass Volume",
> PGAR_2_HPLCOM_VOL, 0, 118, 1, output_stage_tlv),
> SOC_SINGLE_TLV("Left HPCOM Mixer DACR1 Playback Volume",
> DACR1_2_HPLCOM_VOL, 0, 118, 1, output_stage_tlv),
>
> - SOC_SINGLE_TLV("Right HPCOM Mixer Line2L Bypass Volume",
> - LINE2L_2_HPRCOM_VOL, 0, 118, 1, output_stage_tlv),
> SOC_SINGLE_TLV("Right HPCOM Mixer PGAL Bypass Volume",
> PGAL_2_HPRCOM_VOL, 0, 118, 1, output_stage_tlv),
> SOC_SINGLE_TLV("Right HPCOM Mixer DACL1 Playback Volume",
> DACL1_2_HPRCOM_VOL, 0, 118, 1, output_stage_tlv),
>
> /* Stereo output controls for direct L-to-L and R-to-R routes */
> - SOC_DOUBLE_R_TLV("Line Line2 Bypass Volume",
> - LINE2L_2_LLOPM_VOL, LINE2R_2_RLOPM_VOL,
> - 0, 118, 1, output_stage_tlv),
> SOC_DOUBLE_R_TLV("Line PGA Bypass Volume",
> PGAL_2_LLOPM_VOL, PGAR_2_RLOPM_VOL,
> 0, 118, 1, output_stage_tlv),
> @@ -369,9 +355,6 @@ static const struct snd_kcontrol_new aic3x_snd_controls[] = {
> DACL1_2_LLOPM_VOL, DACR1_2_RLOPM_VOL,
> 0, 118, 1, output_stage_tlv),
>
> - SOC_DOUBLE_R_TLV("HP Line2 Bypass Volume",
> - LINE2L_2_HPLOUT_VOL, LINE2R_2_HPROUT_VOL,
> - 0, 118, 1, output_stage_tlv),
> SOC_DOUBLE_R_TLV("HP PGA Bypass Volume",
> PGAL_2_HPLOUT_VOL, PGAR_2_HPROUT_VOL,
> 0, 118, 1, output_stage_tlv),
> @@ -379,9 +362,6 @@ static const struct snd_kcontrol_new aic3x_snd_controls[] = {
> DACL1_2_HPLOUT_VOL, DACR1_2_HPROUT_VOL,
> 0, 118, 1, output_stage_tlv),
>
> - SOC_DOUBLE_R_TLV("HPCOM Line2 Bypass Volume",
> - LINE2L_2_HPLCOM_VOL, LINE2R_2_HPRCOM_VOL,
> - 0, 118, 1, output_stage_tlv),
> SOC_DOUBLE_R_TLV("HPCOM PGA Bypass Volume",
> PGAL_2_HPLCOM_VOL, PGAR_2_HPRCOM_VOL,
> 0, 118, 1, output_stage_tlv),
> @@ -424,6 +404,45 @@ static const struct snd_kcontrol_new aic3x_snd_controls[] = {
> SOC_ENUM("Output Driver Ramp-up step", aic3x_rampup_step_enum),
> };
>
> +/* For other than tlv320aic3104 */
> +static const struct snd_kcontrol_new aic3x_extra_snd_controls[] = {
> + /*
> + * Output controls that map to output mixer switches. Note these are
> + * only for swapped L-to-R and R-to-L routes. See below stereo controls
> + * for direct L-to-L and R-to-R routes.
> + */
> + SOC_SINGLE_TLV("Left Line Mixer Line2R Bypass Volume",
> + LINE2R_2_LLOPM_VOL, 0, 118, 1, output_stage_tlv),
> +
> + SOC_SINGLE_TLV("Right Line Mixer Line2L Bypass Volume",
> + LINE2L_2_RLOPM_VOL, 0, 118, 1, output_stage_tlv),
> +
> + SOC_SINGLE_TLV("Left HP Mixer Line2R Bypass Volume",
> + LINE2R_2_HPLOUT_VOL, 0, 118, 1, output_stage_tlv),
> +
> + SOC_SINGLE_TLV("Right HP Mixer Line2L Bypass Volume",
> + LINE2L_2_HPROUT_VOL, 0, 118, 1, output_stage_tlv),
> +
> + SOC_SINGLE_TLV("Left HPCOM Mixer Line2R Bypass Volume",
> + LINE2R_2_HPLCOM_VOL, 0, 118, 1, output_stage_tlv),
> +
> + SOC_SINGLE_TLV("Right HPCOM Mixer Line2L Bypass Volume",
> + LINE2L_2_HPRCOM_VOL, 0, 118, 1, output_stage_tlv),
> +
> + /* Stereo output controls for direct L-to-L and R-to-R routes */
> + SOC_DOUBLE_R_TLV("Line Line2 Bypass Volume",
> + LINE2L_2_LLOPM_VOL, LINE2R_2_RLOPM_VOL,
> + 0, 118, 1, output_stage_tlv),
> +
> + SOC_DOUBLE_R_TLV("HP Line2 Bypass Volume",
> + LINE2L_2_HPLOUT_VOL, LINE2R_2_HPROUT_VOL,
> + 0, 118, 1, output_stage_tlv),
> +
> + SOC_DOUBLE_R_TLV("HPCOM Line2 Bypass Volume",
> + LINE2L_2_HPLCOM_VOL, LINE2R_2_HPRCOM_VOL,
> + 0, 118, 1, output_stage_tlv),
> +};
> +
> static const struct snd_kcontrol_new aic3x_mono_controls[] = {
> SOC_DOUBLE_R_TLV("Mono Line2 Bypass Volume",
> LINE2L_2_MONOLOPM_VOL, LINE2R_2_MONOLOPM_VOL,
> @@ -464,22 +483,24 @@ SOC_DAPM_ENUM("Route", aic3x_right_hpcom_enum);
>
> /* Left Line Mixer */
> static const struct snd_kcontrol_new aic3x_left_line_mixer_controls[] = {
> - SOC_DAPM_SINGLE("Line2L Bypass Switch", LINE2L_2_LLOPM_VOL, 7, 1, 0),
> SOC_DAPM_SINGLE("PGAL Bypass Switch", PGAL_2_LLOPM_VOL, 7, 1, 0),
> SOC_DAPM_SINGLE("DACL1 Switch", DACL1_2_LLOPM_VOL, 7, 1, 0),
> - SOC_DAPM_SINGLE("Line2R Bypass Switch", LINE2R_2_LLOPM_VOL, 7, 1, 0),
> SOC_DAPM_SINGLE("PGAR Bypass Switch", PGAR_2_LLOPM_VOL, 7, 1, 0),
> SOC_DAPM_SINGLE("DACR1 Switch", DACR1_2_LLOPM_VOL, 7, 1, 0),
> + /* Not on tlv320aic3104 */
> + SOC_DAPM_SINGLE("Line2L Bypass Switch", LINE2L_2_LLOPM_VOL, 7, 1, 0),
> + SOC_DAPM_SINGLE("Line2R Bypass Switch", LINE2R_2_LLOPM_VOL, 7, 1, 0),
> };
>
> /* Right Line Mixer */
> static const struct snd_kcontrol_new aic3x_right_line_mixer_controls[] = {
> - SOC_DAPM_SINGLE("Line2L Bypass Switch", LINE2L_2_RLOPM_VOL, 7, 1, 0),
> SOC_DAPM_SINGLE("PGAL Bypass Switch", PGAL_2_RLOPM_VOL, 7, 1, 0),
> SOC_DAPM_SINGLE("DACL1 Switch", DACL1_2_RLOPM_VOL, 7, 1, 0),
> - SOC_DAPM_SINGLE("Line2R Bypass Switch", LINE2R_2_RLOPM_VOL, 7, 1, 0),
> SOC_DAPM_SINGLE("PGAR Bypass Switch", PGAR_2_RLOPM_VOL, 7, 1, 0),
> SOC_DAPM_SINGLE("DACR1 Switch", DACR1_2_RLOPM_VOL, 7, 1, 0),
> + /* Not on tlv320aic3104 */
> + SOC_DAPM_SINGLE("Line2L Bypass Switch", LINE2L_2_RLOPM_VOL, 7, 1, 0),
> + SOC_DAPM_SINGLE("Line2R Bypass Switch", LINE2R_2_RLOPM_VOL, 7, 1, 0),
> };
>
> /* Mono Mixer */
> @@ -494,42 +515,46 @@ static const struct snd_kcontrol_new aic3x_mono_mixer_controls[] = {
>
> /* Left HP Mixer */
> static const struct snd_kcontrol_new aic3x_left_hp_mixer_controls[] = {
> - SOC_DAPM_SINGLE("Line2L Bypass Switch", LINE2L_2_HPLOUT_VOL, 7, 1, 0),
> SOC_DAPM_SINGLE("PGAL Bypass Switch", PGAL_2_HPLOUT_VOL, 7, 1, 0),
> SOC_DAPM_SINGLE("DACL1 Switch", DACL1_2_HPLOUT_VOL, 7, 1, 0),
> - SOC_DAPM_SINGLE("Line2R Bypass Switch", LINE2R_2_HPLOUT_VOL, 7, 1, 0),
> SOC_DAPM_SINGLE("PGAR Bypass Switch", PGAR_2_HPLOUT_VOL, 7, 1, 0),
> SOC_DAPM_SINGLE("DACR1 Switch", DACR1_2_HPLOUT_VOL, 7, 1, 0),
> + /* Not on tlv320aic3104 */
> + SOC_DAPM_SINGLE("Line2L Bypass Switch", LINE2L_2_HPLOUT_VOL, 7, 1, 0),
> + SOC_DAPM_SINGLE("Line2R Bypass Switch", LINE2R_2_HPLOUT_VOL, 7, 1, 0),
> };
>
> /* Right HP Mixer */
> static const struct snd_kcontrol_new aic3x_right_hp_mixer_controls[] = {
> - SOC_DAPM_SINGLE("Line2L Bypass Switch", LINE2L_2_HPROUT_VOL, 7, 1, 0),
> SOC_DAPM_SINGLE("PGAL Bypass Switch", PGAL_2_HPROUT_VOL, 7, 1, 0),
> SOC_DAPM_SINGLE("DACL1 Switch", DACL1_2_HPROUT_VOL, 7, 1, 0),
> - SOC_DAPM_SINGLE("Line2R Bypass Switch", LINE2R_2_HPROUT_VOL, 7, 1, 0),
> SOC_DAPM_SINGLE("PGAR Bypass Switch", PGAR_2_HPROUT_VOL, 7, 1, 0),
> SOC_DAPM_SINGLE("DACR1 Switch", DACR1_2_HPROUT_VOL, 7, 1, 0),
> + /* Not on tlv320aic3104 */
> + SOC_DAPM_SINGLE("Line2L Bypass Switch", LINE2L_2_HPROUT_VOL, 7, 1, 0),
> + SOC_DAPM_SINGLE("Line2R Bypass Switch", LINE2R_2_HPROUT_VOL, 7, 1, 0),
> };
>
> /* Left HPCOM Mixer */
> static const struct snd_kcontrol_new aic3x_left_hpcom_mixer_controls[] = {
> - SOC_DAPM_SINGLE("Line2L Bypass Switch", LINE2L_2_HPLCOM_VOL, 7, 1, 0),
> SOC_DAPM_SINGLE("PGAL Bypass Switch", PGAL_2_HPLCOM_VOL, 7, 1, 0),
> SOC_DAPM_SINGLE("DACL1 Switch", DACL1_2_HPLCOM_VOL, 7, 1, 0),
> - SOC_DAPM_SINGLE("Line2R Bypass Switch", LINE2R_2_HPLCOM_VOL, 7, 1, 0),
> SOC_DAPM_SINGLE("PGAR Bypass Switch", PGAR_2_HPLCOM_VOL, 7, 1, 0),
> SOC_DAPM_SINGLE("DACR1 Switch", DACR1_2_HPLCOM_VOL, 7, 1, 0),
> + /* Not on tlv320aic3104 */
> + SOC_DAPM_SINGLE("Line2L Bypass Switch", LINE2L_2_HPLCOM_VOL, 7, 1, 0),
> + SOC_DAPM_SINGLE("Line2R Bypass Switch", LINE2R_2_HPLCOM_VOL, 7, 1, 0),
> };
>
> /* Right HPCOM Mixer */
> static const struct snd_kcontrol_new aic3x_right_hpcom_mixer_controls[] = {
> - SOC_DAPM_SINGLE("Line2L Bypass Switch", LINE2L_2_HPRCOM_VOL, 7, 1, 0),
> SOC_DAPM_SINGLE("PGAL Bypass Switch", PGAL_2_HPRCOM_VOL, 7, 1, 0),
> SOC_DAPM_SINGLE("DACL1 Switch", DACL1_2_HPRCOM_VOL, 7, 1, 0),
> - SOC_DAPM_SINGLE("Line2R Bypass Switch", LINE2R_2_HPRCOM_VOL, 7, 1, 0),
> SOC_DAPM_SINGLE("PGAR Bypass Switch", PGAR_2_HPRCOM_VOL, 7, 1, 0),
> SOC_DAPM_SINGLE("DACR1 Switch", DACR1_2_HPRCOM_VOL, 7, 1, 0),
> + /* Not on tlv320aic3104 */
> + SOC_DAPM_SINGLE("Line2L Bypass Switch", LINE2L_2_HPRCOM_VOL, 7, 1, 0),
> + SOC_DAPM_SINGLE("Line2R Bypass Switch", LINE2R_2_HPRCOM_VOL, 7, 1, 0),
> };
>
> /* Left PGA Mixer */
> @@ -550,6 +575,22 @@ static const struct snd_kcontrol_new aic3x_right_pga_mixer_controls[] = {
> SOC_DAPM_SINGLE_AIC3X("Mic3R Switch", MIC3LR_2_RADC_CTRL, 0, 1, 1),
> };
>
> +/* Left PGA Mixer for tlv320aic3104 */
> +static const struct snd_kcontrol_new aic3104_left_pga_mixer_controls[] = {
> + SOC_DAPM_SINGLE_AIC3X("Line1L Switch", LINE1L_2_LADC_CTRL, 3, 1, 1),
> + SOC_DAPM_SINGLE_AIC3X("Line1R Switch", LINE1R_2_LADC_CTRL, 3, 1, 1),
> + SOC_DAPM_SINGLE_AIC3X("Mic2L Switch", MIC3LR_2_LADC_CTRL, 4, 1, 1),
> + SOC_DAPM_SINGLE_AIC3X("Mic2R Switch", MIC3LR_2_LADC_CTRL, 0, 1, 1),
> +};
> +
> +/* Right PGA Mixer for tlv320aic3104 */
> +static const struct snd_kcontrol_new aic3104_right_pga_mixer_controls[] = {
> + SOC_DAPM_SINGLE_AIC3X("Line1R Switch", LINE1R_2_RADC_CTRL, 3, 1, 1),
> + SOC_DAPM_SINGLE_AIC3X("Line1L Switch", LINE1L_2_RADC_CTRL, 3, 1, 1),
> + SOC_DAPM_SINGLE_AIC3X("Mic2L Switch", MIC3LR_2_RADC_CTRL, 4, 1, 1),
> + SOC_DAPM_SINGLE_AIC3X("Mic2R Switch", MIC3LR_2_RADC_CTRL, 0, 1, 1),
> +};
> +
> /* Left Line1 Mux */
> static const struct snd_kcontrol_new aic3x_left_line1l_mux_controls =
> SOC_DAPM_ENUM("Route", aic3x_line1l_2_l_enum);
> @@ -593,26 +634,56 @@ static const struct snd_soc_dapm_widget aic3x_dapm_widgets[] = {
>
> /* Inputs to Left ADC */
> SND_SOC_DAPM_ADC("Left ADC", "Left Capture", LINE1L_2_LADC_CTRL, 2, 0),
> - SND_SOC_DAPM_MIXER("Left PGA Mixer", SND_SOC_NOPM, 0, 0,
> - &aic3x_left_pga_mixer_controls[0],
> - ARRAY_SIZE(aic3x_left_pga_mixer_controls)),
> SND_SOC_DAPM_MUX("Left Line1L Mux", SND_SOC_NOPM, 0, 0,
> &aic3x_left_line1l_mux_controls),
> SND_SOC_DAPM_MUX("Left Line1R Mux", SND_SOC_NOPM, 0, 0,
> &aic3x_left_line1r_mux_controls),
> - SND_SOC_DAPM_MUX("Left Line2L Mux", SND_SOC_NOPM, 0, 0,
> - &aic3x_left_line2_mux_controls),
>
> /* Inputs to Right ADC */
> SND_SOC_DAPM_ADC("Right ADC", "Right Capture",
> LINE1R_2_RADC_CTRL, 2, 0),
> - SND_SOC_DAPM_MIXER("Right PGA Mixer", SND_SOC_NOPM, 0, 0,
> - &aic3x_right_pga_mixer_controls[0],
> - ARRAY_SIZE(aic3x_right_pga_mixer_controls)),
> SND_SOC_DAPM_MUX("Right Line1L Mux", SND_SOC_NOPM, 0, 0,
> &aic3x_right_line1l_mux_controls),
> SND_SOC_DAPM_MUX("Right Line1R Mux", SND_SOC_NOPM, 0, 0,
> &aic3x_right_line1r_mux_controls),
> +
> + /* Mic Bias */
> + SND_SOC_DAPM_SUPPLY("Mic Bias", MICBIAS_CTRL, 6, 0,
> + mic_bias_event,
> + SND_SOC_DAPM_POST_PMU | SND_SOC_DAPM_PRE_PMD),
> +
> + SND_SOC_DAPM_OUTPUT("LLOUT"),
> + SND_SOC_DAPM_OUTPUT("RLOUT"),
> + SND_SOC_DAPM_OUTPUT("HPLOUT"),
> + SND_SOC_DAPM_OUTPUT("HPROUT"),
> + SND_SOC_DAPM_OUTPUT("HPLCOM"),
> + SND_SOC_DAPM_OUTPUT("HPRCOM"),
> +
> + SND_SOC_DAPM_INPUT("LINE1L"),
> + SND_SOC_DAPM_INPUT("LINE1R"),
> +
> + /*
> + * Virtual output pin to detection block inside codec. This can be
> + * used to keep codec bias on if gpio or detection features are needed.
> + * Force pin on or construct a path with an input jack and mic bias
> + * widgets.
> + */
> + SND_SOC_DAPM_OUTPUT("Detection"),
> +};
> +
> +/* For other than tlv320aic3104 */
> +static const struct snd_soc_dapm_widget aic3x_extra_dapm_widgets[] = {
> + /* Inputs to Left ADC */
> + SND_SOC_DAPM_MIXER("Left PGA Mixer", SND_SOC_NOPM, 0, 0,
> + &aic3x_left_pga_mixer_controls[0],
> + ARRAY_SIZE(aic3x_left_pga_mixer_controls)),
> + SND_SOC_DAPM_MUX("Left Line2L Mux", SND_SOC_NOPM, 0, 0,
> + &aic3x_left_line2_mux_controls),
> +
> + /* Inputs to Right ADC */
> + SND_SOC_DAPM_MIXER("Right PGA Mixer", SND_SOC_NOPM, 0, 0,
> + &aic3x_right_pga_mixer_controls[0],
> + ARRAY_SIZE(aic3x_right_pga_mixer_controls)),
> SND_SOC_DAPM_MUX("Right Line2R Mux", SND_SOC_NOPM, 0, 0,
> &aic3x_right_line2_mux_controls),
>
> @@ -637,11 +708,6 @@ static const struct snd_soc_dapm_widget aic3x_dapm_widgets[] = {
> SND_SOC_DAPM_REG(snd_soc_dapm_micbias, "DMic Rate 32",
> AIC3X_ASD_INTF_CTRLA, 0, 3, 3, 0),
>
> - /* Mic Bias */
> - SND_SOC_DAPM_SUPPLY("Mic Bias", MICBIAS_CTRL, 6, 0,
> - mic_bias_event,
> - SND_SOC_DAPM_POST_PMU | SND_SOC_DAPM_PRE_PMD),
> -
> /* Output mixers */
> SND_SOC_DAPM_MIXER("Left Line Mixer", SND_SOC_NOPM, 0, 0,
> &aic3x_left_line_mixer_controls[0],
> @@ -662,27 +728,46 @@ static const struct snd_soc_dapm_widget aic3x_dapm_widgets[] = {
> &aic3x_right_hpcom_mixer_controls[0],
> ARRAY_SIZE(aic3x_right_hpcom_mixer_controls)),
>
> - SND_SOC_DAPM_OUTPUT("LLOUT"),
> - SND_SOC_DAPM_OUTPUT("RLOUT"),
> - SND_SOC_DAPM_OUTPUT("HPLOUT"),
> - SND_SOC_DAPM_OUTPUT("HPROUT"),
> - SND_SOC_DAPM_OUTPUT("HPLCOM"),
> - SND_SOC_DAPM_OUTPUT("HPRCOM"),
> -
> SND_SOC_DAPM_INPUT("MIC3L"),
> SND_SOC_DAPM_INPUT("MIC3R"),
> - SND_SOC_DAPM_INPUT("LINE1L"),
> - SND_SOC_DAPM_INPUT("LINE1R"),
> SND_SOC_DAPM_INPUT("LINE2L"),
> SND_SOC_DAPM_INPUT("LINE2R"),
> +};
>
> - /*
> - * Virtual output pin to detection block inside codec. This can be
> - * used to keep codec bias on if gpio or detection features are needed.
> - * Force pin on or construct a path with an input jack and mic bias
> - * widgets.
> - */
> - SND_SOC_DAPM_OUTPUT("Detection"),
> +/* For tlv320aic3104 */
> +static const struct snd_soc_dapm_widget aic3104_extra_dapm_widgets[] = {
> + /* Inputs to Left ADC */
> + SND_SOC_DAPM_MIXER("Left PGA Mixer", SND_SOC_NOPM, 0, 0,
> + &aic3104_left_pga_mixer_controls[0],
> + ARRAY_SIZE(aic3104_left_pga_mixer_controls)),
> +
> + /* Inputs to Right ADC */
> + SND_SOC_DAPM_MIXER("Right PGA Mixer", SND_SOC_NOPM, 0, 0,
> + &aic3104_right_pga_mixer_controls[0],
> + ARRAY_SIZE(aic3104_right_pga_mixer_controls)),
> +
> + /* Output mixers */
> + SND_SOC_DAPM_MIXER("Left Line Mixer", SND_SOC_NOPM, 0, 0,
> + &aic3x_left_line_mixer_controls[0],
> + ARRAY_SIZE(aic3x_left_line_mixer_controls) - 2),
> + SND_SOC_DAPM_MIXER("Right Line Mixer", SND_SOC_NOPM, 0, 0,
> + &aic3x_right_line_mixer_controls[0],
> + ARRAY_SIZE(aic3x_right_line_mixer_controls) - 2),
> + SND_SOC_DAPM_MIXER("Left HP Mixer", SND_SOC_NOPM, 0, 0,
> + &aic3x_left_hp_mixer_controls[0],
> + ARRAY_SIZE(aic3x_left_hp_mixer_controls) - 2),
> + SND_SOC_DAPM_MIXER("Right HP Mixer", SND_SOC_NOPM, 0, 0,
> + &aic3x_right_hp_mixer_controls[0],
> + ARRAY_SIZE(aic3x_right_hp_mixer_controls) - 2),
> + SND_SOC_DAPM_MIXER("Left HPCOM Mixer", SND_SOC_NOPM, 0, 0,
> + &aic3x_left_hpcom_mixer_controls[0],
> + ARRAY_SIZE(aic3x_left_hpcom_mixer_controls) - 2),
> + SND_SOC_DAPM_MIXER("Right HPCOM Mixer", SND_SOC_NOPM, 0, 0,
> + &aic3x_right_hpcom_mixer_controls[0],
> + ARRAY_SIZE(aic3x_right_hpcom_mixer_controls) - 2),
> +
> + SND_SOC_DAPM_INPUT("MIC2L"),
> + SND_SOC_DAPM_INPUT("MIC2R"),
> };
>
> static const struct snd_soc_dapm_widget aic3x_dapm_mono_widgets[] = {
> @@ -712,17 +797,10 @@ static const struct snd_soc_dapm_route intercon[] = {
> {"Left Line1R Mux", "single-ended", "LINE1R"},
> {"Left Line1R Mux", "differential", "LINE1R"},
>
> - {"Left Line2L Mux", "single-ended", "LINE2L"},
> - {"Left Line2L Mux", "differential", "LINE2L"},
> -
> {"Left PGA Mixer", "Line1L Switch", "Left Line1L Mux"},
> {"Left PGA Mixer", "Line1R Switch", "Left Line1R Mux"},
> - {"Left PGA Mixer", "Line2L Switch", "Left Line2L Mux"},
> - {"Left PGA Mixer", "Mic3L Switch", "MIC3L"},
> - {"Left PGA Mixer", "Mic3R Switch", "MIC3R"},
>
> {"Left ADC", NULL, "Left PGA Mixer"},
> - {"Left ADC", NULL, "GPIO1 dmic modclk"},
>
> /* Right Input */
> {"Right Line1R Mux", "single-ended", "LINE1R"},
> @@ -730,25 +808,10 @@ static const struct snd_soc_dapm_route intercon[] = {
> {"Right Line1L Mux", "single-ended", "LINE1L"},
> {"Right Line1L Mux", "differential", "LINE1L"},
>
> - {"Right Line2R Mux", "single-ended", "LINE2R"},
> - {"Right Line2R Mux", "differential", "LINE2R"},
> -
> {"Right PGA Mixer", "Line1L Switch", "Right Line1L Mux"},
> {"Right PGA Mixer", "Line1R Switch", "Right Line1R Mux"},
> - {"Right PGA Mixer", "Line2R Switch", "Right Line2R Mux"},
> - {"Right PGA Mixer", "Mic3L Switch", "MIC3L"},
> - {"Right PGA Mixer", "Mic3R Switch", "MIC3R"},
>
> {"Right ADC", NULL, "Right PGA Mixer"},
> - {"Right ADC", NULL, "GPIO1 dmic modclk"},
> -
> - /*
> - * Logical path between digital mic enable and GPIO1 modulator clock
> - * output function
> - */
> - {"GPIO1 dmic modclk", NULL, "DMic Rate 128"},
> - {"GPIO1 dmic modclk", NULL, "DMic Rate 64"},
> - {"GPIO1 dmic modclk", NULL, "DMic Rate 32"},
>
> /* Left DAC Output */
> {"Left DAC Mux", "DAC_L1", "Left DAC"},
> @@ -761,10 +824,8 @@ static const struct snd_soc_dapm_route intercon[] = {
> {"Right DAC Mux", "DAC_R3", "Right DAC"},
>
> /* Left Line Output */
> - {"Left Line Mixer", "Line2L Bypass Switch", "Left Line2L Mux"},
> {"Left Line Mixer", "PGAL Bypass Switch", "Left PGA Mixer"},
> {"Left Line Mixer", "DACL1 Switch", "Left DAC Mux"},
> - {"Left Line Mixer", "Line2R Bypass Switch", "Right Line2R Mux"},
> {"Left Line Mixer", "PGAR Bypass Switch", "Right PGA Mixer"},
> {"Left Line Mixer", "DACR1 Switch", "Right DAC Mux"},
>
> @@ -773,10 +834,8 @@ static const struct snd_soc_dapm_route intercon[] = {
> {"LLOUT", NULL, "Left Line Out"},
>
> /* Right Line Output */
> - {"Right Line Mixer", "Line2L Bypass Switch", "Left Line2L Mux"},
> {"Right Line Mixer", "PGAL Bypass Switch", "Left PGA Mixer"},
> {"Right Line Mixer", "DACL1 Switch", "Left DAC Mux"},
> - {"Right Line Mixer", "Line2R Bypass Switch", "Right Line2R Mux"},
> {"Right Line Mixer", "PGAR Bypass Switch", "Right PGA Mixer"},
> {"Right Line Mixer", "DACR1 Switch", "Right DAC Mux"},
>
> @@ -785,10 +844,8 @@ static const struct snd_soc_dapm_route intercon[] = {
> {"RLOUT", NULL, "Right Line Out"},
>
> /* Left HP Output */
> - {"Left HP Mixer", "Line2L Bypass Switch", "Left Line2L Mux"},
> {"Left HP Mixer", "PGAL Bypass Switch", "Left PGA Mixer"},
> {"Left HP Mixer", "DACL1 Switch", "Left DAC Mux"},
> - {"Left HP Mixer", "Line2R Bypass Switch", "Right Line2R Mux"},
> {"Left HP Mixer", "PGAR Bypass Switch", "Right PGA Mixer"},
> {"Left HP Mixer", "DACR1 Switch", "Right DAC Mux"},
>
> @@ -797,10 +854,8 @@ static const struct snd_soc_dapm_route intercon[] = {
> {"HPLOUT", NULL, "Left HP Out"},
>
> /* Right HP Output */
> - {"Right HP Mixer", "Line2L Bypass Switch", "Left Line2L Mux"},
> {"Right HP Mixer", "PGAL Bypass Switch", "Left PGA Mixer"},
> {"Right HP Mixer", "DACL1 Switch", "Left DAC Mux"},
> - {"Right HP Mixer", "Line2R Bypass Switch", "Right Line2R Mux"},
> {"Right HP Mixer", "PGAR Bypass Switch", "Right PGA Mixer"},
> {"Right HP Mixer", "DACR1 Switch", "Right DAC Mux"},
>
> @@ -809,10 +864,8 @@ static const struct snd_soc_dapm_route intercon[] = {
> {"HPROUT", NULL, "Right HP Out"},
>
> /* Left HPCOM Output */
> - {"Left HPCOM Mixer", "Line2L Bypass Switch", "Left Line2L Mux"},
> {"Left HPCOM Mixer", "PGAL Bypass Switch", "Left PGA Mixer"},
> {"Left HPCOM Mixer", "DACL1 Switch", "Left DAC Mux"},
> - {"Left HPCOM Mixer", "Line2R Bypass Switch", "Right Line2R Mux"},
> {"Left HPCOM Mixer", "PGAR Bypass Switch", "Right PGA Mixer"},
> {"Left HPCOM Mixer", "DACR1 Switch", "Right DAC Mux"},
>
> @@ -823,10 +876,8 @@ static const struct snd_soc_dapm_route intercon[] = {
> {"HPLCOM", NULL, "Left HP Com"},
>
> /* Right HPCOM Output */
> - {"Right HPCOM Mixer", "Line2L Bypass Switch", "Left Line2L Mux"},
> {"Right HPCOM Mixer", "PGAL Bypass Switch", "Left PGA Mixer"},
> {"Right HPCOM Mixer", "DACL1 Switch", "Left DAC Mux"},
> - {"Right HPCOM Mixer", "Line2R Bypass Switch", "Right Line2R Mux"},
> {"Right HPCOM Mixer", "PGAR Bypass Switch", "Right PGA Mixer"},
> {"Right HPCOM Mixer", "DACR1 Switch", "Right DAC Mux"},
>
> @@ -839,6 +890,72 @@ static const struct snd_soc_dapm_route intercon[] = {
> {"HPRCOM", NULL, "Right HP Com"},
> };
>
> +/* For other than tlv320aic3104 */
> +static const struct snd_soc_dapm_route intercon_extra[] = {
> + /* Left Input */
> + {"Left Line2L Mux", "single-ended", "LINE2L"},
> + {"Left Line2L Mux", "differential", "LINE2L"},
> +
> + {"Left PGA Mixer", "Line2L Switch", "Left Line2L Mux"},
> + {"Left PGA Mixer", "Mic3L Switch", "MIC3L"},
> + {"Left PGA Mixer", "Mic3R Switch", "MIC3R"},
> +
> + {"Left ADC", NULL, "GPIO1 dmic modclk"},
> +
> + /* Right Input */
> + {"Right Line2R Mux", "single-ended", "LINE2R"},
> + {"Right Line2R Mux", "differential", "LINE2R"},
> +
> + {"Right PGA Mixer", "Line2R Switch", "Right Line2R Mux"},
> + {"Right PGA Mixer", "Mic3L Switch", "MIC3L"},
> + {"Right PGA Mixer", "Mic3R Switch", "MIC3R"},
> +
> + {"Right ADC", NULL, "GPIO1 dmic modclk"},
> +
> + /*
> + * Logical path between digital mic enable and GPIO1 modulator clock
> + * output function
> + */
> + {"GPIO1 dmic modclk", NULL, "DMic Rate 128"},
> + {"GPIO1 dmic modclk", NULL, "DMic Rate 64"},
> + {"GPIO1 dmic modclk", NULL, "DMic Rate 32"},
> +
> + /* Left Line Output */
> + {"Left Line Mixer", "Line2L Bypass Switch", "Left Line2L Mux"},
> + {"Left Line Mixer", "Line2R Bypass Switch", "Right Line2R Mux"},
> +
> + /* Right Line Output */
> + {"Right Line Mixer", "Line2L Bypass Switch", "Left Line2L Mux"},
> + {"Right Line Mixer", "Line2R Bypass Switch", "Right Line2R Mux"},
> +
> + /* Left HP Output */
> + {"Left HP Mixer", "Line2L Bypass Switch", "Left Line2L Mux"},
> + {"Left HP Mixer", "Line2R Bypass Switch", "Right Line2R Mux"},
> +
> + /* Right HP Output */
> + {"Right HP Mixer", "Line2L Bypass Switch", "Left Line2L Mux"},
> + {"Right HP Mixer", "Line2R Bypass Switch", "Right Line2R Mux"},
> +
> + /* Left HPCOM Output */
> + {"Left HPCOM Mixer", "Line2L Bypass Switch", "Left Line2L Mux"},
> + {"Left HPCOM Mixer", "Line2R Bypass Switch", "Right Line2R Mux"},
> +
> + /* Right HPCOM Output */
> + {"Right HPCOM Mixer", "Line2L Bypass Switch", "Left Line2L Mux"},
> + {"Right HPCOM Mixer", "Line2R Bypass Switch", "Right Line2R Mux"},
> +};
> +
> +/* For other than tlv320aic3104 */
> +static const struct snd_soc_dapm_route intercon_extra_3104[] = {
> + /* Left Input */
> + {"Left PGA Mixer", "Mic2L Switch", "MIC2L"},
> + {"Left PGA Mixer", "Mic2R Switch", "MIC2R"},
> +
> + /* Right Input */
> + {"Right PGA Mixer", "Mic2L Switch", "MIC2L"},
> + {"Right PGA Mixer", "Mic2R Switch", "MIC2R"},
> +};
> +
> static const struct snd_soc_dapm_route intercon_mono[] = {
> /* Mono Output */
> {"Mono Mixer", "Line2L Bypass Switch", "Left Line2L Mux"},
> @@ -867,17 +984,31 @@ static int aic3x_add_widgets(struct snd_soc_codec *codec)
> switch (aic3x->model) {
> case AIC3X_MODEL_3X:
> case AIC3X_MODEL_33:
> + snd_soc_dapm_new_controls(dapm, aic3x_extra_dapm_widgets,
> + ARRAY_SIZE(aic3x_extra_dapm_widgets));
> + snd_soc_dapm_add_routes(dapm, intercon_extra,
> + ARRAY_SIZE(intercon_extra));
> snd_soc_dapm_new_controls(dapm, aic3x_dapm_mono_widgets,
> ARRAY_SIZE(aic3x_dapm_mono_widgets));
> snd_soc_dapm_add_routes(dapm, intercon_mono,
> ARRAY_SIZE(intercon_mono));
> break;
> case AIC3X_MODEL_3007:
> + snd_soc_dapm_new_controls(dapm, aic3x_extra_dapm_widgets,
> + ARRAY_SIZE(aic3x_extra_dapm_widgets));
> + snd_soc_dapm_add_routes(dapm, intercon_extra,
> + ARRAY_SIZE(intercon_extra));
> snd_soc_dapm_new_controls(dapm, aic3007_dapm_widgets,
> ARRAY_SIZE(aic3007_dapm_widgets));
> snd_soc_dapm_add_routes(dapm, intercon_3007,
> ARRAY_SIZE(intercon_3007));
> break;
> + case AIC3X_MODEL_3104:
> + snd_soc_dapm_new_controls(dapm, aic3104_extra_dapm_widgets,
> + ARRAY_SIZE(aic3104_extra_dapm_widgets));
> + snd_soc_dapm_add_routes(dapm, intercon_extra_3104,
> + ARRAY_SIZE(intercon_extra_3104));
> + break;
> }
>
> return 0;
> @@ -1438,23 +1569,33 @@ static int aic3x_probe(struct snd_soc_codec *codec)
> aic3x_init(codec);
>
> if (aic3x->setup) {
> - /* setup GPIO functions */
> - snd_soc_write(codec, AIC3X_GPIO1_REG,
> - (aic3x->setup->gpio_func[0] & 0xf) << 4);
> - snd_soc_write(codec, AIC3X_GPIO2_REG,
> - (aic3x->setup->gpio_func[1] & 0xf) << 4);
> + if (aic3x->model != AIC3X_MODEL_3104) {
> + /* setup GPIO functions */
> + snd_soc_write(codec, AIC3X_GPIO1_REG,
> + (aic3x->setup->gpio_func[0] & 0xf) << 4);
> + snd_soc_write(codec, AIC3X_GPIO2_REG,
> + (aic3x->setup->gpio_func[1] & 0xf) << 4);
> + } else {
> + dev_warn(codec->dev, "GPIO functionality is not supported on tlv320aic3104\n");
> + }
> }
>
> switch (aic3x->model) {
> case AIC3X_MODEL_3X:
> case AIC3X_MODEL_33:
> + snd_soc_add_codec_controls(codec, aic3x_extra_snd_controls,
> + ARRAY_SIZE(aic3x_extra_snd_controls));
> snd_soc_add_codec_controls(codec, aic3x_mono_controls,
> ARRAY_SIZE(aic3x_mono_controls));
> break;
> case AIC3X_MODEL_3007:
> + snd_soc_add_codec_controls(codec, aic3x_extra_snd_controls,
> + ARRAY_SIZE(aic3x_extra_snd_controls));
> snd_soc_add_codec_controls(codec,
> &aic3x_classd_amp_gain_ctrl, 1);
> break;
> + case AIC3X_MODEL_3104:
> + break;
> }
>
> /* set mic bias voltage */
> @@ -1522,6 +1663,7 @@ static const struct i2c_device_id aic3x_i2c_id[] = {
> { "tlv320aic33", AIC3X_MODEL_33 },
> { "tlv320aic3007", AIC3X_MODEL_3007 },
> { "tlv320aic3106", AIC3X_MODEL_3X },
> + { "tlv320aic3104", AIC3X_MODEL_3104 },
> { }
> };
> MODULE_DEVICE_TABLE(i2c, aic3x_i2c_id);
>
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
