Hi Prabhakar,
On Mon, 26 Jan 2015, Lad, Prabhakar wrote:
> Hi Benoit,
>
> On Mon, Jan 26, 2015 at 3:50 PM, Benoit Parrot <bparrot@xxxxxx> wrote:
> > Lad, Prabhakar <prabhakar.csengg@xxxxxxxxx> wrote on Mon [2015-Jan-26 08:13:01 +0000]:
> >> Hi Paul,
> >>
> >> Thanks for the review.
> >>
> >> On Mon, Jan 26, 2015 at 2:15 AM, Paul Walmsley <paul@xxxxxxxxx> wrote:
> >> > Hi
> >> >
> >> > On Sun, 25 Jan 2015, Lad, Prabhakar wrote:
> >> >
> >> >> From: Benoit Parrot <bparrot@xxxxxx>
> >> >>
> >> >> this patch adds VPFE HWMOD data for AM43xx.
> >> >>
> >> >> Signed-off-by: Benoit Parrot <bparrot@xxxxxx>
> >> >> Signed-off-by: Darren Etheridge <detheridge@xxxxxx>
> >> >> Signed-off-by: Felipe Balbi <balbi@xxxxxx>
> >> >> Signed-off-by: Lad, Prabhakar <prabhakar.csengg@xxxxxxxxx>
> >> >> ---
> >> >> Hi Paul,
> >> >>
> >> >> You were right, the hardware team has confirmed that, the VPFE master port is
> >> >> connected to L3 and the VPFE slave port is connected to L4. The L3 port cannot
> >> >> serve as a register target because it is initiator only.
> >> >
> >> > OK makes sense to me.,
> >> >
> >> >>
> >> >> I have created links referring to dss l3/l4 hwmod and tested it, lemme know
> >> >> if I have missed something.
> >> >
> >> > A few minor comments below
> >> >
> >> >>
> >> [Snip]
> >> >> /* Interfaces */
> >> >> static struct omap_hwmod_ocp_if am43xx_l3_main__l4_hs = {
> >> >> .master = &am33xx_l3_main_hwmod,
> >> >> @@ -788,6 +826,36 @@ static struct omap_hwmod_ocp_if am43xx_l4_ls__dss_rfbi = {
> >> >> .user = OCP_USER_MPU | OCP_USER_SDMA,
> >> >> };
> >> >>
> >> >> +static struct omap_hwmod_ocp_if am43xx_l3__vpfe0 = {
> >> >> + .master = &am43xx_vpfe0_hwmod,
> >> >> + .slave = &am33xx_l3_main_hwmod,
> >> >> + .clk = "l3_gclk",
> >> >> + .flags = OCPIF_SWSUP_IDLE,
> >> >
> >> > OCPIF_SWSUP_IDLE probably isn't needed here. Could you please try without
> >> > it?
> >> >
> >> >> + .user = OCP_USER_MPU | OCP_USER_SDMA,
> >> >> +};
> >> >> +
> >> >> +static struct omap_hwmod_ocp_if am43xx_l3__vpfe1 = {
> >> >> + .master = &am43xx_vpfe1_hwmod,
> >> >> + .slave = &am33xx_l3_main_hwmod,
> >> >> + .clk = "l3_gclk",
> >> >> + .flags = OCPIF_SWSUP_IDLE,
> >> >
> >> > Same point as the above.
> >> >
> >> Dropped and tested works! posting a v3.
> >
> > When you tested it without the OCPIF_SWSUP_IDLE, did you go trhough a complete suspend/resume cycle?
> > This flag was added early on because otherwise the susbsytem would not go idle without it...
> >
> > Can you post the console output during a suspend/resume cycle?
> >
> Ah I didn’t test the suspend/resume will do and post the console log.
Could you also do a suspend/resume test on v2?
thanks
- Paul
