Re: [PATCH 2/4] ARM: dts: Add basic dm816x device tree configuration

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



* Tony Lindgren <tony@xxxxxxxxxxx> [150115 15:05]:
> 
> For reference, the devices I've confirmed to work so far are:
> 
> - intc
> - timers
> - gpmc
> - i2c
> - ethernet and mdio
> - mmc
> - edma
> - uart
> 
> Updated patch below with the mailbox fixed.

Got the spi working too. The it needs to be compatible with
ti,omap4-mcspi with four chip selects. Updated patch below.

Also added the pinctrl-single entry.

Regards,

Tony

8< ------------------
From: Tony Lindgren <tony@xxxxxxxxxxx>
Date: Wed, 14 Jan 2015 17:45:22 -0800
Subject: [PATCH] ARM: dts: Add basic dm816x device tree configuration

Similar to other omap variants, let's add dm816x support.

Note that this is based on generated data from the
TI81XX-LINUX-PSP-04.04.00.02 patches published at:

http://downloads.ti.com/dsps/dsps_public_sw/psp/LinuxPSP/TI81XX_04_04/04_04_00_02/index_FDS.html

I've verified the basic functionality, but have not been
able to test all the devices on dm8168-evm.

Cc: Brian Hutchinson <b.hutchman@xxxxxxxxx>
Signed-off-by: Tony Lindgren <tony@xxxxxxxxxxx>

--- /dev/null
+++ b/arch/arm/boot/dts/dm816x.dtsi
@@ -0,0 +1,386 @@
+/*
+ * This file is licensed under the terms of the GNU General Public License
+ * version 2.  This program is licensed "as is" without any warranty of any
+ * kind, whether express or implied.
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/omap.h>
+
+#include "skeleton.dtsi"
+
+/ {
+	compatible = "ti,dm816";
+	interrupt-parent = <&intc>;
+
+	aliases {
+		i2c0 = &i2c1;
+		i2c1 = &i2c2;
+		serial0 = &uart1;
+		serial1 = &uart2;
+		serial2 = &uart3;
+		ethernet0 = &eth0;
+		ethernet1 = &eth1;
+	};
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		cpu@0 {
+			compatible = "arm,cortex-a8";
+			device_type = "cpu";
+			reg = <0>;
+		};
+	};
+
+	pmu {
+		compatible = "arm,cortex-a8-pmu";
+		interrupts = <3>;
+	};
+
+	/*
+	 * The soc node represents the soc top level view. It is used for IPs
+	 * that are not memory mapped in the MPU view or for the MPU itself.
+	 */
+	soc {
+		compatible = "ti,omap-infra";
+		mpu {
+			compatible = "ti,omap3-mpu";
+			ti,hwmods = "mpu";
+		};
+	};
+
+	dm816x_pinmux: pinmux@44e10800 {
+		compatible = "pinctrl-single";
+		reg = <0x48140800 0x50a>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		pinctrl-single,register-width = <16>;
+		pinctrl-single,function-mask = <0xf>;
+	};
+
+	/*
+	 * XXX: Use a flat representation of the dm816x interconnect.
+	 * The real dm816x interconnect network is quite complex. Since
+	 * it will not bring real advantage to represent that in DT
+	 * for the moment, just use a fake OCP bus entry to represent
+	 * the whole bus hierarchy.
+	 */
+	ocp {
+		compatible = "ti,omap3-l3-smx", "simple-bus";
+		reg = <0x44000000 0x10000>;
+		interrupts = <9 10>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+		ti,hwmods = "l3_main";
+
+		prcm: prcm@48180000 {
+			compatible = "ti,dm816-prcm";
+			reg = <0x48180000 0x4000>;
+
+			prcm_clocks: clocks {
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+
+			prcm_clockdomains: clockdomains {
+			};
+		};
+
+		scrm: scrm@48140000 {
+			compatible = "ti,dm816-scrm";
+			reg = <0x48140000 0x21000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0x48140000 0x21000>;
+
+			scrm_clocks: clocks {
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+
+			scrm_clockdomains: clockdomains {
+			};
+		};
+
+		cm: syscon@44e10000 {
+			compatible = "ti,am33xx-controlmodule", "syscon";
+			reg = <0x44e10000 0x800>;
+		};
+
+		edma: edma@49000000 {
+			compatible = "ti,edma3";
+			ti,hwmods = "tpcc", "tptc0", "tptc1", "tptc2", "tptc3";
+			reg =   <0x49000000 0x10000>,
+			        <0x44e10f90 0x40>;
+			interrupts = <12 13 14>;
+			#dma-cells = <1>;
+		};
+
+		elm: elm@48080000 {
+			compatible = "ti,816-elm";
+			ti,hwmods = "elm";
+			reg = <0x48080000 0x2000>;
+			interrupts = <4>;
+		};
+
+		gpio1: gpio@48032000 {
+			compatible = "ti,omap3-gpio";
+			ti,hwmods = "gpio1";
+			reg = <0x48032000 0x1000>;
+			interrupts = <97>;
+		};
+
+		gpio2: gpio@4804c000 {
+			compatible = "ti,omap3-gpio";
+			ti,hwmods = "gpio2";
+			reg = <0x4804c000 0x1000>;
+			interrupts = <99>;
+		};
+
+		gpmc: gpmc@50000000 {
+			compatible = "ti,am3352-gpmc";
+			ti,hwmods = "gpmc";
+			reg = <0x50000000 0x2000>;
+			#address-cells = <2>;
+			#size-cells = <1>;
+			interrupts = <100>;
+			gpmc,num-cs = <6>;
+			gpmc,num-waitpins = <2>;
+		};
+
+		i2c1: i2c@48028000 {
+			compatible = "ti,omap4-i2c";
+			ti,hwmods = "i2c1";
+			reg = <0x48028000 0x1000>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			interrupts = <70>;
+			dmas = <&edma 58 &edma 59>;
+			dma-names = "tx", "rx";
+		};
+
+		i2c2: i2c@4802a000 {
+			compatible = "ti,omap4-i2c";
+			ti,hwmods = "i2c2";
+			reg = <0x4802a000 0x1000>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			interrupts = <71>;
+			dmas = <&edma 60 &edma 61>;
+			dma-names = "tx", "rx";
+		};
+
+		intc: interrupt-controller@48200000 {
+			compatible = "ti,dm816-intc";
+			interrupt-controller;
+			#interrupt-cells = <1>;
+			reg = <0x48200000 0x1000>;
+		};
+
+		mailbox: mailbox@480c8000 {
+			compatible = "ti,omap4-mailbox";
+			reg = <0x480c8000 0x2000>;
+			interrupts = <77>;
+			ti,hwmods = "mailbox";
+			ti,mbox-num-users = <4>;
+			ti,mbox-num-fifos = <12>;
+			mbox_dsp: mbox_dsp {
+				ti,mbox-tx = <3 0 0>;
+				ti,mbox-rx = <0 0 0>;
+			};
+		};
+
+		mdio: mdio@4a100800 {
+			compatible = "ti,davinci_mdio";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x4a100800 0x100>;
+			ti,hwmods = "davinci_mdio";
+			bus_freq = <1000000>;
+			phy0: ethernet-phy@0 {
+				reg = <1>;
+			};
+			phy1: ethernet-phy@1 {
+				reg = <2>;
+			};
+		};
+
+		eth0: ethernet@4a100000 {
+			compatible = "ti,dm816-emac";
+			ti,hwmods = "emac0";
+			reg = <0x4a100000 0x800
+			       0x4a100900 0x3700>;
+			clocks = <&sysclk24_ck>;
+			ti,davinci-ctrl-reg-offset = <0>;
+			ti,davinci-ctrl-mod-reg-offset = <0x900>;
+			ti,davinci-ctrl-ram-offset = <0x2000>;
+			ti,davinci-ctrl-ram-size = <0x2000>;
+			interrupts = <40 41 42 43>;
+			phy-handle = <&phy0>;
+		};
+
+		eth1: ethernet@4a120000 {
+			compatible = "ti,dm816-emac";
+			ti,hwmods = "emac1";
+			reg = <0x4a120000 0x4000>;
+			clocks = <&sysclk24_ck>;
+			ti,davinci-ctrl-reg-offset = <0>;
+			ti,davinci-ctrl-mod-reg-offset = <0x900>;
+			ti,davinci-ctrl-ram-offset = <0x2000>;
+			ti,davinci-ctrl-ram-size = <0x2000>;
+			interrupts = <44 45 46 47>;
+			phy-handle = <&phy1>;
+		};
+
+		mcspi1: spi@48030000 {
+			compatible = "ti,omap4-mcspi";
+			reg = <0x48030000 0x1000>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			interrupts = <65>;
+			ti,spi-num-cs = <4>;
+			ti,hwmods = "mcspi1";
+			dmas = <&edma 16 &edma 17
+				&edma 18 &edma 19>;
+			dma-names = "tx0", "rx0", "tx1", "rx1";
+		};
+
+		mmc1: mmc@48060000 {
+			compatible = "ti,omap4-hsmmc";
+			reg = <0x48060000 0x11000>;
+			ti,hwmods = "mmc1";
+			interrupts = <64>;
+			dmas = <&edma 24 &edma 25>;
+			dma-names = "tx", "rx";
+		};
+
+		timer1: timer@4802e000 {
+			compatible = "ti,dm816-timer";
+			reg = <0x4802e000 0x2000>;
+			interrupts = <67>;
+			ti,hwmods = "timer1";
+			ti,timer-alwon;
+		};
+
+		timer2: timer@48040000 {
+			compatible = "ti,dm816-timer";
+			reg = <0x48040000 0x2000>;
+			interrupts = <68>;
+			ti,hwmods = "timer2";
+		};
+
+		timer3: timer@48042000 {
+			compatible = "ti,dm816-timer";
+			reg = <0x48042000 0x2000>;
+			interrupts = <69>;
+			ti,hwmods = "timer3";
+		};
+
+		timer4: timer@48044000 {
+			compatible = "ti,dm816-timer";
+			reg = <0x48044000 0x2000>;
+			interrupts = <92>;
+			ti,hwmods = "timer4";
+		};
+
+		timer5: timer@48046000 {
+			compatible = "ti,dm816-timer";
+			reg = <0x48046000 0x2000>;
+			interrupts = <93>;
+			ti,hwmods = "timer5";
+		};
+
+		timer6: timer@48048000 {
+			compatible = "ti,dm816-timer";
+			reg = <0x48048000 0x2000>;
+			interrupts = <94>;
+			ti,hwmods = "timer6";
+		};
+
+		timer7: timer@4804a000 {
+			compatible = "ti,dm816-timer";
+			reg = <0x4804a000 0x2000>;
+			interrupts = <95>;
+			ti,hwmods = "timer7";
+		};
+
+		uart1: uart@48020000 {
+			compatible = "ti,omap3-uart";
+			ti,hwmods = "uart1";
+			reg = <0x48020000 0x2000>;
+			clock-frequency = <48000000>;
+			interrupts = <72>;
+			dmas = <&edma 26 &edma 27>;
+			dma-names = "tx", "rx";
+		};
+
+		uart2: uart@48022000 {
+			compatible = "ti,omap3-uart";
+			ti,hwmods = "uart2";
+			reg = <0x48022000 0x2000>;
+			clock-frequency = <48000000>;
+			interrupts = <73>;
+			dmas = <&edma 28 &edma 29>;
+			dma-names = "tx", "rx";
+		};
+
+		uart3: uart@48024000 {
+			compatible = "ti,omap3-uart";
+			ti,hwmods = "uart3";
+			reg = <0x48024000 0x2000>;
+			clock-frequency = <48000000>;
+			interrupts = <74>;
+			dmas = <&edma 30 &edma 31>;
+			dma-names = "tx", "rx";
+		};
+
+		/* NOTE: USB needs a transceiver driver for phys to work */
+		usb: usb_otg_hs@47401000 {
+			compatible = "ti,am33xx-usb";
+			reg = <0x47401000 0x400000>;
+			ranges;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ti,hwmods = "usb_otg_hs";
+
+			usb0: usb@47401000 {
+				compatible = "ti,musb-am33xx";
+				reg = <0x47401400 0x400
+				       0x47401000 0x200>;
+				reg-names = "mc", "control";
+				interrupts = <18>;
+				interrupt-names = "mc";
+				dr_mode = "otg";
+				mentor,multipoint = <1>;
+				mentor,num-eps = <16>;
+				mentor,ram-bits = <12>;
+				mentor,power = <500>;
+			};
+
+			usb1: usb@47401800 {
+				compatible = "ti,musb-am33xx";
+				status = "disabled";
+				reg = <0x47401c00 0x400
+				       0x47401800 0x200>;
+				reg-names = "mc", "control";
+				interrupts = <19>;
+				interrupt-names = "mc";
+				dr_mode = "otg";
+				mentor,multipoint = <1>;
+				mentor,num-eps = <16>;
+				mentor,ram-bits = <12>;
+				mentor,power = <500>;
+			};
+		};
+
+		wd_timer2: wd_timer@480c2000 {
+			compatible = "ti,omap3-wdt";
+			ti,hwmods = "wd_timer";
+			reg = <0x480c2000 0x1000>;
+			interrupts = <0>;
+		};
+	};
+};
+
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html



[Index of Archives]     [Linux Arm (vger)]     [ARM Kernel]     [ARM MSM]     [Linux Tegra]     [Linux WPAN Networking]     [Linux Wireless Networking]     [Maemo Users]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Yosemite Trails]     [Linux Kernel]     [Linux SCSI]

  Powered by Linux