On Thu, May 29, 2014 at 02:07:59PM +0530, Satish Patel wrote:
>
>
> On 5/29/2014 12:14 AM, Greg KH wrote:
> >On Wed, May 28, 2014 at 02:27:14PM +0530, Satish Patel wrote:
> >>TDA8026 is a SmartCard PHY from NXP.
> >>
> >>The PHY interfaces with the main processor over the
> >>I2C interface and acts as a slave device.
> >>
> >>The driver also exposes the phy interface
> >>(defined@include/linux/sc_phy.h) for SmartCard controller.
> >>Controller uses this interface to communicate with smart card
> >>inserted to the phy's slot.
> >>
> >>Note: gpio irq is not validated as I do not have device with that.
> >>I have validated interrupt with dedicated interrupt line on my device.
> >>
> >>Signed-off-by: Satish Patel <satish.patel@xxxxxx>
> >>---
> >> Documentation/devicetree/bindings/misc/tda8026.txt | 19 +
> >> drivers/misc/Kconfig | 7 +
> >> drivers/misc/Makefile | 1 +
> >> drivers/misc/tda8026.c | 1258 ++++++++++++++++++++
> >> 4 files changed, 1285 insertions(+)
> >> create mode 100644 Documentation/devicetree/bindings/misc/tda8026.txt
> >> create mode 100644 drivers/misc/tda8026.c
> >>
> >>diff --git a/Documentation/devicetree/bindings/misc/tda8026.txt b/Documentation/devicetree/bindings/misc/tda8026.txt
> >>new file mode 100644
> >>index 0000000..f115c9c
> >>--- /dev/null
> >>+++ b/Documentation/devicetree/bindings/misc/tda8026.txt
> >>@@ -0,0 +1,19 @@
> >>+TDA8026 smart card slot interface
> >>+
> >>+This is an i2c based smart card interface device forming the electrical
> >>+interface between a microcontroller and smart cards. This device supports
> >>+asynchronous cards (micro controller-based IC cards) as well as synchronous
> >>+cards (mainly memory cards)
> >>+
> >>+Required properties:
> >>+- compatible: "nxp,tda8026"
> >>+- shutdown-gpio = GPIO pin mapping for SDWNN pin
> >>+- reg = i2c interface address
> >>+
> >>+
> >>+Example:
> >>+tda8026: tda8026@48 {
> >>+ compatible = "nxp,tda8026";
> >>+ reg = <0x48>;
> >>+ shutdown-gpio = <&gpio5 19 GPIO_ACTIVE_HIGH>;/* Bank5, pin19 */
> >>+ };
> >>diff --git a/drivers/misc/Kconfig b/drivers/misc/Kconfig
> >>index 8baff0e..80b21d7 100644
> >>--- a/drivers/misc/Kconfig
> >>+++ b/drivers/misc/Kconfig
> >>@@ -515,6 +515,13 @@ config SRAM
> >> the genalloc API. It is supposed to be used for small on-chip SRAM
> >> areas found on many SoCs.
> >>
> >>+config NXP_TDA8026_PHY
> >>+ tristate "NXP PHY Driver for Smart Card PHY"
> >>+ depends on I2C=y
> >>+ help
> >>+ If you say yes here you get support for the TDA8026 Smart card PHY
> >>+ with I2C interface.
> >>+
> >> source "drivers/misc/c2port/Kconfig"
> >> source "drivers/misc/eeprom/Kconfig"
> >> source "drivers/misc/cb710/Kconfig"
> >>diff --git a/drivers/misc/Makefile b/drivers/misc/Makefile
> >>index 7eb4b69..f262c0b 100644
> >>--- a/drivers/misc/Makefile
> >>+++ b/drivers/misc/Makefile
> >>@@ -55,3 +55,4 @@ obj-$(CONFIG_SRAM) += sram.o
> >> obj-y += mic/
> >> obj-$(CONFIG_GENWQE) += genwqe/
> >> obj-$(CONFIG_ECHO) += echo/
> >>+obj-$(CONFIG_NXP_TDA8026_PHY) += tda8026.o
> >>diff --git a/drivers/misc/tda8026.c b/drivers/misc/tda8026.c
> >>new file mode 100644
> >>index 0000000..38df33e
> >>--- /dev/null
> >>+++ b/drivers/misc/tda8026.c
> >>@@ -0,0 +1,1258 @@
> >>+/*
> >>+ * tda8026.c - TDA8026 PHY driver for NXP Smart card PHY
> >>+ *
> >>+ *
> >>+ * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com/
> >>+ *
> >>+ * This program is free software; you can redistribute it and/or
> >>+ * modify it under the terms of the GNU General Public License as
> >>+ * published by the Free Software Foundation version 2.
> >>+ *
> >>+ * This program is distributed "as is" WITHOUT ANY WARRANTY of any
> >>+ * kind, whether express or implied; without even the implied warranty
> >>+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> >>+ * GNU General Public License for more details.
> >>+ */
> >>+
> >>+#include <linux/module.h>
> >>+#include <linux/moduleparam.h>
> >>+#include <linux/interrupt.h>
> >>+#include <linux/init.h>
> >>+#include <linux/slab.h>
> >>+#include <linux/gpio.h>
> >>+#include <linux/i2c.h>
> >>+#include <linux/mfd/core.h>
> >>+#include <linux/notifier.h>
> >>+#include <linux/sc_phy.h>
> >>+#include <linux/of_gpio.h>
> >>+#include <linux/of_device.h>
> >>+#include <linux/delay.h>
> >
> >I think you just broke the build if this driver is enabled now right?
> >
> >Not good :(
> Before sending, I have applied these patches to "v3.15-rc7" and build with
> both the option ti-usim & tda8026 as module, as well as part of kernel. Any
> specific tree you would like me to rebase these patches against.
Did you try applying the patches one-by-one and building afterwards
between each one? In looking at this further, I think it will work, but
please test and make sure. You can not break the build with any
individual patch.
thanks,
greg k-h
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
