On 03/12/2014 05:49 AM, Pekon Gupta wrote: > Adds pinmux and DT node for Micron (MT29F4G08AB) x8 NAND device present on > am437x-gp-evm board. > (1) As NAND Flash data lines are muxed with eMMC, Thus at a given time either > eMMC or NAND can be enabled. Selection between eMMC and NAND is controlled: > (a) By dynamically driving following GPIO pin from software > SPI2_CS0(GPIO) == 0 NAND is selected (default) > SPI2_CS0(GPIO) == 1 eMMC is selected > (b) By statically using Jumper (J89) on the board > > (2) As NAND device connnected to this board has page-size=4K and oob-size=224, > So ROM code expects boot-loaders to be flashed in BCH16 ECC scheme for > NAND boot. > > Signed-off-by: Pekon Gupta <pekon@xxxxxx> > --- > arch/arm/boot/dts/am437x-gp-evm.dts | 107 ++++++++++++++++++++++++++++++++++++ > 1 file changed, 107 insertions(+) > > diff --git a/arch/arm/boot/dts/am437x-gp-evm.dts b/arch/arm/boot/dts/am437x-gp-evm.dts > index df8798e..0027ea7 100644 > --- a/arch/arm/boot/dts/am437x-gp-evm.dts > +++ b/arch/arm/boot/dts/am437x-gp-evm.dts which branch does this apply on? I assume you mean this for Tony's omap-for-v3.15/dt branch? it would be nice if you'd make that clear in cover letter. > @@ -81,6 +81,27 @@ > 0x164 MUX_MODE0 /* eCAP0_in_PWM0_out.eCAP0_in_PWM0_out MODE0 */ > >; > }; > + > + nand_flash_x8: nand_flash_x8 { > + pinctrl-single,pins = < > + 0x26C(PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* spi2_cs0.gpio/eMMCorNANDsel */ > + 0x0 (PIN_INPUT | MUX_MODE0) /* gpmc_ad0.gpmc_ad0 */ > + 0x4 (PIN_INPUT | MUX_MODE0) /* gpmc_ad1.gpmc_ad1 */ > + 0x8 (PIN_INPUT | MUX_MODE0) /* gpmc_ad2.gpmc_ad2 */ > + 0xc (PIN_INPUT | MUX_MODE0) /* gpmc_ad3.gpmc_ad3 */ > + 0x10 (PIN_INPUT | MUX_MODE0) /* gpmc_ad4.gpmc_ad4 */ > + 0x14 (PIN_INPUT | MUX_MODE0) /* gpmc_ad5.gpmc_ad5 */ > + 0x18 (PIN_INPUT | MUX_MODE0) /* gpmc_ad6.gpmc_ad6 */ > + 0x1c (PIN_INPUT | MUX_MODE0) /* gpmc_ad7.gpmc_ad7 */ > + 0x70 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_wait0.gpmc_wait0 */ > + 0x74 (PIN_OUTPUT_PULLUP | MUX_MODE7) /* gpmc_wpn.gpmc_wpn */ > + 0x7c (PIN_OUTPUT | MUX_MODE0) /* gpmc_csn0.gpmc_csn0 */ > + 0x90 (PIN_OUTPUT | MUX_MODE0) /* gpmc_advn_ale.gpmc_advn_ale */ > + 0x94 (PIN_OUTPUT | MUX_MODE0) /* gpmc_oen_ren.gpmc_oen_ren */ > + 0x98 (PIN_OUTPUT | MUX_MODE0) /* gpmc_wen.gpmc_wen */ > + 0x9c (PIN_OUTPUT | MUX_MODE0) /* gpmc_be0n_cle.gpmc_be0n_cle */ > + >; > + }; > }; > > &i2c0 { > @@ -125,3 +146,89 @@ > pinctrl-0 = <&mmc1_pins>; > cd-gpios = <&gpio0 6 GPIO_ACTIVE_HIGH>; > }; > + > +&elm { > + status = "okay"; > +}; > + > +&gpmc { > + status = "okay"; > + pinctrl-names = "default"; > + pinctrl-0 = <&nand_flash_x8>; > + ranges = <0 0 0x08000000 0x10000000>; /* CS0: NAND */ > + nand@0,0 { > + reg = <0 0 0>; /* CS0, offset 0 */ > + ti,nand-ecc-opt = "bch8"; > + ti,elm-id = <&elm>; > + nand-bus-width = <8>; > + gpmc,device-width = <1>; > + gpmc,sync-clk-ps = <0>; > + gpmc,cs-on-ns = <0>; > + gpmc,cs-rd-off-ns = <40>; > + gpmc,cs-wr-off-ns = <40>; > + gpmc,adv-on-ns = <0>; > + gpmc,adv-rd-off-ns = <25>; > + gpmc,adv-wr-off-ns = <25>; > + gpmc,we-on-ns = <0>; > + gpmc,we-off-ns = <20>; > + gpmc,oe-on-ns = <3>; > + gpmc,oe-off-ns = <30>; > + gpmc,access-ns = <30>; > + gpmc,rd-cycle-ns = <40>; > + gpmc,wr-cycle-ns = <40>; > + gpmc,wait-on-read = "true"; > + gpmc,wait-on-write = "true"; > + gpmc,bus-turnaround-ns = <0>; > + gpmc,cycle2cycle-delay-ns = <0>; > + gpmc,clk-activation-ns = <0>; > + gpmc,wait-monitoring-ns = <0>; > + gpmc,wr-access-ns = <40>; > + gpmc,wr-data-mux-bus-ns = <0>; > + /* MTD partition table */ > + /* All SPL-* partitions are sized to minimal length > + * which can be independently programmable. For > + * NAND flash this is equal to size of erase-block */ > + #address-cells = <1>; > + #size-cells = <1>; > + partition@0 { > + label = "NAND.SPL"; > + reg = <0x00000000 0x00040000>; > + }; > + partition@1 { > + label = "NAND.SPL.backup1"; > + reg = <0x00040000 0x00040000>; > + }; > + partition@2 { > + label = "NAND.SPL.backup2"; > + reg = <0x00080000 0x00040000>; > + }; > + partition@3 { > + label = "NAND.SPL.backup3"; > + reg = <0x000C0000 0x00040000>; > + }; > + partition@4 { > + label = "NAND.u-boot-spl-os"; > + reg = <0x00100000 0x00080000>; > + }; > + partition@5 { > + label = "NAND.u-boot"; > + reg = <0x00180000 0x00100000>; > + }; > + partition@6 { > + label = "NAND.u-boot-env"; > + reg = <0x00280000 0x00040000>; > + }; > + partition@7 { > + label = "NAND.u-boot-env.backup1"; > + reg = <0x002C0000 0x00040000>; > + }; > + partition@8 { > + label = "NAND.kernel"; > + reg = <0x00300000 0x00700000>; > + }; > + partition@9 { > + label = "NAND.file-system"; > + reg = <0x00A00000 0x1F600000>; > + }; > + }; > +}; > -- Regards, Nishanth Menon -- To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html