MMC2 is used by the on-board WiFi module populated on some boards
(based on Marvell Libertas 8688 SDIO). The Bluetooth is connected
to UART2.
Signed-off-by: Florian Vaussard <florian.vaussard@xxxxxxx>
---
arch/arm/boot/dts/omap3-overo-base.dtsi | 72 ++++++++++++++++++++++++++++++++
arch/arm/boot/dts/omap3-overo-storm.dtsi | 8 ++++
arch/arm/boot/dts/omap3-overo.dtsi | 8 ++++
3 files changed, 88 insertions(+)
diff --git a/arch/arm/boot/dts/omap3-overo-base.dtsi b/arch/arm/boot/dts/omap3-overo-base.dtsi
index aea64c0..edac70e 100644
--- a/arch/arm/boot/dts/omap3-overo-base.dtsi
+++ b/arch/arm/boot/dts/omap3-overo-base.dtsi
@@ -29,9 +29,50 @@
ti,mcbsp = <&mcbsp2>;
ti,codec = <&twl_audio>;
};
+
+ /* Regulator to trigger the nPoweron signal of the Wifi module */
+ w3cbw003c_npoweron: regulator-w3cbw003c-npoweron {
+ compatible = "regulator-fixed";
+ regulator-name = "regulator-w3cbw003c-npoweron";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&gpio2 22 GPIO_ACTIVE_HIGH>; /* gpio_54: nPoweron */
+ enable-active-high;
+ };
+
+ /* Regulator to trigger the nReset signal of the Wifi module */
+ w3cbw003c_wifi_nreset: regulator-w3cbw003c-wifi-nreset {
+ pinctrl-names = "default";
+ pinctrl-0 = <&w3cbw003c_pins &w3cbw003c_2_pins>;
+ compatible = "regulator-fixed";
+ regulator-name = "regulator-w3cbw003c-wifi-nreset";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&gpio1 16 GPIO_ACTIVE_HIGH>; /* gpio_16: WiFi nReset */
+ startup-delay-us = <10000>;
+ };
+
+ /* Regulator to trigger the nReset signal of the Bluetooth module */
+ w3cbw003c_bt_nreset: regulator-w3cbw003c-bt-nreset {
+ compatible = "regulator-fixed";
+ regulator-name = "regulator-w3cbw003c-bt-nreset";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&gpio6 4 GPIO_ACTIVE_HIGH>; /* gpio_164: BT nReset */
+ startup-delay-us = <10000>;
+ };
};
&omap3_pmx_core {
+ uart2_pins: pinmux_uart2_pins {
+ pinctrl-single,pins = <
+ OMAP3_CORE1_IOPAD(0x216c, PIN_INPUT | MUX_MODE1) /* mcbsp3_dx.uart2_cts */
+ OMAP3_CORE1_IOPAD(0x216e, PIN_OUTPUT | MUX_MODE1) /* mcbsp3_dr.uart2_rts */
+ OMAP3_CORE1_IOPAD(0x2170, PIN_OUTPUT | MUX_MODE1) /* mcbsp3_clk.uart2_tx */
+ OMAP3_CORE1_IOPAD(0x2172, PIN_INPUT | MUX_MODE1) /* mcbsp3_fsx.uart2_rx */
+ >;
+ };
+
uart3_pins: pinmux_uart3_pins {
pinctrl-single,pins = <
OMAP3_CORE1_IOPAD(0x219e, PIN_INPUT | PIN_OFF_WAKEUPENABLE | MUX_MODE0) /* uart3_rx_irrx.uart3_rx_irrx */
@@ -56,6 +97,25 @@
OMAP3_CORE1_IOPAD(0x214e, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat3.sdmmc1_dat3 */
>;
};
+
+ mmc2_pins: pinmux_mmc2_pins {
+ pinctrl-single,pins = <
+ OMAP3_CORE1_IOPAD(0x2158, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_clk.sdmmc2_clk */
+ OMAP3_CORE1_IOPAD(0x215a, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_cmd.sdmmc2_cmd */
+ OMAP3_CORE1_IOPAD(0x215c, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat0.sdmmc2_dat0 */
+ OMAP3_CORE1_IOPAD(0x215e, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat1.sdmmc2_dat1 */
+ OMAP3_CORE1_IOPAD(0x2160, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat2.sdmmc2_dat2 */
+ OMAP3_CORE1_IOPAD(0x2162, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat3.sdmmc2_dat3 */
+ >;
+ };
+
+ /* WiFi/BT combo */
+ w3cbw003c_pins: pinmux_w3cbw003c_pins {
+ pinctrl-single,pins = <
+ OMAP3_CORE1_IOPAD(0x20b4, PIN_OUTPUT | MUX_MODE4) /* gpmc_ncs3.gpio_54 */
+ OMAP3_CORE1_IOPAD(0x219c, PIN_OUTPUT | MUX_MODE4) /* uart3_rts_sd.gpio_164 */
+ >;
+ };
};
&i2c1 {
@@ -94,7 +154,14 @@
/* optional on board WiFi */
&mmc2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc2_pins>;
+ vmmc-supply = <&w3cbw003c_npoweron>;
+ vqmmc-supply = <&w3cbw003c_bt_nreset>;
+ vmmc_aux-supply = <&w3cbw003c_wifi_nreset>;
bus-width = <4>;
+ cap-sdio-irq;
+ non-removable;
};
&twl_gpio {
@@ -110,6 +177,11 @@
power = <50>;
};
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart2_pins>;
+};
+
&uart3 {
pinctrl-names = "default";
pinctrl-0 = <&uart3_pins>;
diff --git a/arch/arm/boot/dts/omap3-overo-storm.dtsi b/arch/arm/boot/dts/omap3-overo-storm.dtsi
index c30efb3..c235ae8 100644
--- a/arch/arm/boot/dts/omap3-overo-storm.dtsi
+++ b/arch/arm/boot/dts/omap3-overo-storm.dtsi
@@ -9,3 +9,11 @@
#include "omap36xx.dtsi"
#include "omap3-overo-base.dtsi"
+&omap3_pmx_core2 {
+ w3cbw003c_2_pins: pinmux_w3cbw003c_2_pins {
+ pinctrl-single,pins = <
+ OMAP3630_CORE2_IOPAD(0x25e0, PIN_OUTPUT | MUX_MODE4) /* etk_d2.gpio_16 */
+ >;
+ };
+};
+
diff --git a/arch/arm/boot/dts/omap3-overo.dtsi b/arch/arm/boot/dts/omap3-overo.dtsi
index 7bbda68..95c59b2 100644
--- a/arch/arm/boot/dts/omap3-overo.dtsi
+++ b/arch/arm/boot/dts/omap3-overo.dtsi
@@ -9,3 +9,11 @@
#include "omap34xx.dtsi"
#include "omap3-overo-base.dtsi"
+&omap3_pmx_core2 {
+ w3cbw003c_2_pins: pinmux_w3cbw003c_2_pins {
+ pinctrl-single,pins = <
+ OMAP3430_CORE2_IOPAD(0x25e0, PIN_OUTPUT | MUX_MODE4) /* etk_d2.gpio_16 */
+ >;
+ };
+};
+
--
1.8.3.2
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
