On 03/03/14 13:06, Roger Quadros wrote: > Hi Marc, > > On 03/03/2014 12:04 PM, Marc Murphy wrote: >> Hi, >> I am using the latest stable 3.4.80 kernel with some changes to get the EMAC Phy to initialise correctly after a suspend/resume. The platform is AM3517 with most of the system working nice and smoothly. I have 1 issue though and need some advice/help to get the system to use the USB hub I have connected to the EHCI controller after a suspend to memory and resume. >> >> At boot all is recognised; >> >> [ 1.486816] usbcore: registered new interface driver cdc_ether >> [ 1.493255] usbcore: registered new interface driver cdc_ncm >> [ 1.499450] usbcore: registered new interface driver qmi_wwan >> [ 1.506622] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver >> [ 1.513580] ehci-omap.0 supply hsusb0 not found, using dummy regulator >> [ 2.521881] ehci-omap ehci-omap.0: OMAP-EHCI Host Controller >> [ 2.528411] ehci-omap ehci-omap.0: new USB bus registered, assigned bus number 1 >> [ 2.536468] ehci-omap ehci-omap.0: irq 77, io mem 0x48064800 >> [ 2.553070] ehci-omap ehci-omap.0: USB 2.0 started, EHCI 1.00 >> [ 2.559295] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 >> [ 2.566436] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 >> [ 2.574035] usb usb1: Product: OMAP-EHCI Host Controller >> [ 2.579620] usb usb1: Manufacturer: Linux 3.4.80 ehci_hcd >> [ 2.585296] usb usb1: SerialNumber: ehci-omap.0 >> [ 2.591278] hub 1-0:1.0: USB hub found >> [ 2.595306] hub 1-0:1.0: 3 ports detected >> >> And I can see everything OK. >> >> # lsusb >> Bus 001 Device 002: ID 0424:2513 Standard Microsystems Corp. 2.0 Hub >> Bus 002 Device 002: ID 05e3:0718 Genesys Logic, Inc. IDE/SATA Adapter >> Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub >> Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub >> Bus 001 Device 003: ID 1199:68a2 Sierra Wireless, Inc. >> # >> # >> # echo mem > /sys/power/state >> [ 73.736572] PM: Syncing filesystems ... done. >> [ 73.743530] Freezing user space processes ... (elapsed 0.01 seconds) done. >> [ 73.766784] Freezing remaining freezable tasks ... (elapsed 0.02 seconds) done. >> [ 73.959289] davinci_mdio davinci_mdio.0: timed out waiting for idle >> [ 73.968872] PM: suspend of devices complete after 170.410 msecs >> [ 73.975433] PM: late suspend of devices complete after 0.305 msecs >> [ 73.982635] PM: noirq suspend of devices complete after 0.732 msecs >> [ 83.430450] Powerdomain (core_pwrdm) didn't enter target state 1 >> [ 83.436737] Could not enter target state in pm_suspend >> [ 83.443176] PM: noirq resume of devices complete after 0.915 msecs >> [ 83.450164] PM: early resume of devices complete after 0.274 msecs >> [ 83.457336] <6>Waiting for PHY clock good... >> [ 83.463287] davinci_mdio davinci_mdio.0: resetting idled controller >> [ 83.471343] net eth0: attached PHY driver [SMSC LAN8710/LAN8720] (mii_bus:phy_addr=davinci_mdio-0:00, id=7c0f1) >> [ 84.771881] PM: resume of devices complete after 1315.185 msecs >> [ 84.778472] Restarting tasks ... >> [ 84.782379] usb 1-1: USB disconnect, device number 2 >> [ 84.790557] done. >> [ 84.792938] mmc0: mmc_rescan_try_freq: trying to init card at 400000 Hz >> sh: write error:[ 84.800781] usb 1-1.1: USB disconnect, device number 3 >> Operation not p[ 84.808349] qmi_wwan 1-1.1:1.8: wwan0: unregister 'qmi_wwan' usb-ehci-omap.0-1.1, Sierra Wireless wwan/QMI device >> ermitted >> [ 84.859191] mmc1: mmc_rescan_try_freq: trying to init card at 400000 Hz >> [ 86.490356] PHY: davinci_mdio-0:00 - Link is Up - 100/Full >> # >> # >> # lsusb >> Bus 002 Device 002: ID 05e3:0718 Genesys Logic, Inc. IDE/SATA Adapter >> Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub >> Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub >> # >> >> Is there any relevant patch out there that would address the issue that I see ? > > Does this happen because of OFF mode? > Can you please try the tests with off mode disabled? > > e.g. > mount -t debugfs none /sys/kernel/debug > echo 0 > /sys/kernel/debug/pm_debug/enable_off_mode > suspend & resume AFAIK, AM3517 does not have OFF mode. We had something similar with runtime pm... It might be useful to know which hub is this and how is it connected... > > Also please send the output of /sys/kernel/debug/pm_debug/count > before suspend and after resume. Thanks. -- Regards, Igor. -- To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
