Thanks, Vaibhav Hiremath > -----Original Message----- > From: video4linux-list-bounces@xxxxxxxxxx [mailto:video4linux-list- > bounces@xxxxxxxxxx] On Behalf Of Curran, Dominic > Sent: Friday, January 30, 2009 6:24 AM > To: linux-omap; video4linux-list@xxxxxxxxxx > Cc: greg.hofer@xxxxxx > Subject: [OMAPZOOM][PATCH 4/6] Add support for Sony imx046 to > OMAP3430 SDP board. > > From: Dominic Curran <dcurran@xxxxxx> > Subject: [OMAPZOOM][PATCH 4/6] Add support for Sony imx046 to > OMAP3430 SDP board. > > Support for the Sony IMX046 sensor on the OMAP3430 SDP board. > > Signed-off-by: Greg Hofer <greg.hofer@xxxxxx> > Signed-off-by: Dominic Curran <dcurran@xxxxxx> > --- > arch/arm/mach-omap2/board-3430sdp.c | 197 > ++++++++++++++++++++++++++++++++++++ > 1 file changed, 197 insertions(+) > > Index: omapzoom04/arch/arm/mach-omap2/board-3430sdp.c > =================================================================== > --- omapzoom04.orig/arch/arm/mach-omap2/board-3430sdp.c > +++ omapzoom04/arch/arm/mach-omap2/board-3430sdp.c > @@ -45,6 +45,9 @@ > #include "ti-compat.h" > > #ifdef CONFIG_VIDEO_OMAP3 > +#ifndef CONFIG_TWL4030_CORE > +#error "no power companion board defined!" > +#endif [Hiremath, Vaibhav] Do we really required to do this? > #include <media/v4l2-int-device.h> > #include <../drivers/media/video/omap34xxcam.h> > #include <../drivers/media/video/isp/ispreg.h> > @@ -52,9 +55,11 @@ > #define FPGA_SPR_GPIO1_3v3 (0x1 << 14) > #define FPGA_GPIO6_DIR_CTRL (0x1 << 6) > static void __iomem *fpga_map_addr; > + > #if defined(CONFIG_VIDEO_MT9P012) || > defined(CONFIG_VIDEO_MT9P012_MODULE) > #include <../drivers/media/video/mt9p012.h> > #endif > + > #if defined(CONFIG_VIDEO_OV3640) || > defined(CONFIG_VIDEO_OV3640_MODULE) > #include <../drivers/media/video/ov3640.h> > #include <../drivers/media/video/isp/ispcsi2.h> > @@ -71,6 +76,22 @@ static struct omap34xxcam_hw_config *hwc > #define OV3640_CSI2_PHY_TCLK_MISS 1 > #define OV3640_CSI2_PHY_TCLK_SETTLE 14 > #endif > + > +#if defined(CONFIG_VIDEO_IMX046) || > defined(CONFIG_VIDEO_IMX046_MODULE) > +#include <../drivers/media/video/imx046.h> > +#include <../drivers/media/video/isp/ispcsi2.h> > +#define IMX046_CSI2_CLOCK_POLARITY 0 /* +/- pin order */ > +#define IMX046_CSI2_DATA0_POLARITY 0 /* +/- pin order */ > +#define IMX046_CSI2_DATA1_POLARITY 0 /* +/- pin order */ > +#define IMX046_CSI2_CLOCK_LANE 1 /* Clock lane > position: 1 */ > +#define IMX046_CSI2_DATA0_LANE 2 /* Data0 lane > position: 2 */ > +#define IMX046_CSI2_DATA1_LANE 3 /* Data1 lane > position: 3 */ > +#define IMX046_CSI2_PHY_THS_TERM 2 > +#define IMX046_CSI2_PHY_THS_SETTLE 23 > +#define IMX046_CSI2_PHY_TCLK_TERM 0 > +#define IMX046_CSI2_PHY_TCLK_MISS 1 > +#define IMX046_CSI2_PHY_TCLK_SETTLE 14 > +#endif > #endif > > #ifdef CONFIG_VIDEO_DW9710 > @@ -926,6 +947,176 @@ static struct ov3640_platform_data sdp34 > > #endif > > + > +#if defined(CONFIG_VIDEO_IMX046) || > defined(CONFIG_VIDEO_IMX046_MODULE) > + > +static struct omap34xxcam_sensor_config imx046_hwc = { > + .sensor_isp = 0, > + .xclk = OMAP34XXCAM_XCLK_B, > + .capture_mem = PAGE_ALIGN(3280 * 2464 * 2) * 2, > +}; > + [Hiremath, Vaibhav] You may want to align the structure, same comment I had also received from Tony on MMDC support patch. > +static int imx046_sensor_set_prv_data(void *priv) > +{ > + struct omap34xxcam_hw_config *hwc = priv; > + > + hwc->u.sensor.xclk = imx046_hwc.xclk; > + hwc->u.sensor.sensor_isp = imx046_hwc.sensor_isp; > + hwc->dev_index = 2; > + hwc->dev_minor = 5; > + hwc->dev_type = OMAP34XXCAM_SLAVE_SENSOR; > + hwc->interface_type = ISP_CSIA; > + > + hwc->csi2.hw_csi2.lanes.clock.polarity = > IMX046_CSI2_CLOCK_POLARITY; > + hwc->csi2.hw_csi2.lanes.clock.position = > IMX046_CSI2_CLOCK_LANE; > + hwc->csi2.hw_csi2.lanes.data[0].polarity = > IMX046_CSI2_DATA0_POLARITY; > + hwc->csi2.hw_csi2.lanes.data[0].position = > IMX046_CSI2_DATA0_LANE; > + hwc->csi2.hw_csi2.lanes.data[1].polarity = > IMX046_CSI2_DATA1_POLARITY; > + hwc->csi2.hw_csi2.lanes.data[1].position = > IMX046_CSI2_DATA1_LANE; > + hwc->csi2.hw_csi2.phy.ths_term = IMX046_CSI2_PHY_THS_TERM; > + hwc->csi2.hw_csi2.phy.ths_settle = IMX046_CSI2_PHY_THS_SETTLE; > + hwc->csi2.hw_csi2.phy.tclk_term = IMX046_CSI2_PHY_TCLK_TERM; > + hwc->csi2.hw_csi2.phy.tclk_miss = IMX046_CSI2_PHY_TCLK_MISS; > + hwc->csi2.hw_csi2.phy.tclk_settle = > IMX046_CSI2_PHY_TCLK_SETTLE; > + return 0; > +} > + > +static struct isp_interface_config imx046_if_config = { > + .ccdc_par_ser = ISP_CSIA, > + .dataline_shift = 0x0, > + .hsvs_syncdetect = ISPCTRL_SYNC_DETECT_VSRISE, > + .vdint0_timing = 0x0, > + .vdint1_timing = 0x0, > + .strobe = 0x0, > + .prestrobe = 0x0, > + .shutter = 0x0, > + .prev_sph = 2, > + .prev_slv = 0, > + .wenlog = ISPCCDC_CFG_WENLOG_OR, > + .dcsub = IMX046_BLACK_LEVEL_AVG, > + .u.csi.crc = 0x0, > + .u.csi.mode = 0x0, > + .u.csi.edge = 0x0, > + .u.csi.signalling = 0x0, > + .u.csi.strobe_clock_inv = 0x0, > + .u.csi.vs_edge = 0x0, > + .u.csi.channel = 0x0, > + .u.csi.vpclk = 0x2, > + .u.csi.data_start = 0x0, > + .u.csi.data_size = 0x0, > + .u.csi.format = V4L2_PIX_FMT_SGRBG10, > +}; > + [Hiremath, Vaibhav] Same here. > + > +static int imx046_sensor_power_set(enum v4l2_power power) > +{ > + struct isp_csi2_lanes_cfg lanecfg; > + struct isp_csi2_phy_cfg phyconfig; > + static enum v4l2_power previous_power = V4L2_POWER_OFF; > + int err = 0; > + > + switch (power) { > + case V4L2_POWER_ON: > + /* Power Up Sequence */ > + printk(KERN_DEBUG "imx046_sensor_power_set(ON)\n"); > + if (previous_power == V4L2_POWER_OFF) > + isp_csi2_reset(); > + > + lanecfg.clk.pol = IMX046_CSI2_CLOCK_POLARITY; > + lanecfg.clk.pos = IMX046_CSI2_CLOCK_LANE; > + lanecfg.data[0].pol = IMX046_CSI2_DATA0_POLARITY; > + lanecfg.data[0].pos = IMX046_CSI2_DATA0_LANE; > + lanecfg.data[1].pol = IMX046_CSI2_DATA1_POLARITY; > + lanecfg.data[1].pos = IMX046_CSI2_DATA1_LANE; > + lanecfg.data[2].pol = 0; > + lanecfg.data[2].pos = 0; > + lanecfg.data[3].pol = 0; > + lanecfg.data[3].pos = 0; > + isp_csi2_complexio_lanes_config(&lanecfg); > + isp_csi2_complexio_lanes_update(true); > + > + isp_csi2_ctrl_config_ecc_enable(true); > + > + phyconfig.ths_term = IMX046_CSI2_PHY_THS_TERM; > + phyconfig.ths_settle = IMX046_CSI2_PHY_THS_SETTLE; > + phyconfig.tclk_term = IMX046_CSI2_PHY_TCLK_TERM; > + phyconfig.tclk_miss = IMX046_CSI2_PHY_TCLK_MISS; > + phyconfig.tclk_settle = IMX046_CSI2_PHY_TCLK_SETTLE; > + isp_csi2_phy_config(&phyconfig); > + isp_csi2_phy_update(true); > + > + isp_configure_interface(&imx046_if_config); > + > + if (previous_power == V4L2_POWER_OFF) { > + /* Request and configure gpio pins */ > + if (omap_request_gpio(IMX046_RESET_GPIO) != 0) > + return -EIO; > + > + /* nRESET is active LOW. set HIGH to release reset > */ > + omap_set_gpio_dataout(IMX046_RESET_GPIO, 1); > + > + /* set to output mode */ > + omap_set_gpio_direction(IMX046_RESET_GPIO, > + GPIO_DIR_OUTPUT); > + > + /* turn on analog power */ > + twl4030_i2c_write_u8(TWL4030_MODULE_PM_RECEIVER, > + VAUX_2_8_V, TWL4030_VAUX2_DEDICATED); > + twl4030_i2c_write_u8(TWL4030_MODULE_PM_RECEIVER, > + VAUX_DEV_GRP_P1, > TWL4030_VAUX2_DEV_GRP); > + > + twl4030_i2c_write_u8(TWL4030_MODULE_PM_RECEIVER, > + VAUX_1_8_V, TWL4030_VAUX4_DEDICATED); > + twl4030_i2c_write_u8(TWL4030_MODULE_PM_RECEIVER, > + VAUX_DEV_GRP_P1, > TWL4030_VAUX4_DEV_GRP); > + udelay(100); > + > + /* have to put sensor to reset to guarantee > detection */ > + omap_set_gpio_dataout(IMX046_RESET_GPIO, 0); > + udelay(1500); > + > + /* nRESET is active LOW. set HIGH to release reset > */ > + omap_set_gpio_dataout(IMX046_RESET_GPIO, 1); > + udelay(300); > + } > + break; > + case V4L2_POWER_OFF: > + printk(KERN_DEBUG "imx046_sensor_power_set(OFF)\n"); > + /* Power Down Sequence */ > + isp_csi2_complexio_power(ISP_CSI2_POWER_OFF); > + > + twl4030_i2c_write_u8(TWL4030_MODULE_PM_RECEIVER, > + VAUX_DEV_GRP_NONE, TWL4030_VAUX4_DEV_GRP); > + twl4030_i2c_write_u8(TWL4030_MODULE_PM_RECEIVER, > + VAUX_DEV_GRP_NONE, TWL4030_VAUX2_DEV_GRP); > + omap_free_gpio(IMX046_RESET_GPIO); > + break; > + case V4L2_POWER_STANDBY: > + printk(KERN_DEBUG "imx046_sensor_power_set(STANDBY)\n"); > + /*TODO*/ > + break; > + } > + > + /* Save powerstate to know what was before calling POWER_ON. > */ > + previous_power = power; > + return err; > +} > + > +static struct imx046_platform_data sdp3430_imx046_platform_data = { > + .power_set = imx046_sensor_power_set, > + .priv_data_set = imx046_sensor_set_prv_data, > + .default_regs = NULL, > + .set_xclk = isp_set_xclk, > + .cfg_interface_bridge = isp_configure_interface_bridge, > + .csi2_lane_count = isp_csi2_complexio_lanes_count, > + .csi2_cfg_vp_out_ctrl = isp_csi2_ctrl_config_vp_out_ctrl, > + .csi2_ctrl_update = isp_csi2_ctrl_update, > + .csi2_cfg_virtual_id = isp_csi2_ctx_config_virtual_id, > + .csi2_ctx_update = isp_csi2_ctx_update, > + .csi2_calc_phy_cfg0 = isp_csi2_calc_phy_cfg0, > +}; > +#endif > + > static struct platform_device sdp3430_lcd_device = { > .name = "sdp2430_lcd", > .id = -1, > @@ -1063,6 +1254,12 @@ static struct i2c_board_info __initdata > .platform_data = &sdp3430_ov3640_platform_data, > }, > #endif > +#if defined(CONFIG_VIDEO_IMX046) || > defined(CONFIG_VIDEO_IMX046_MODULE) > + { > + I2C_BOARD_INFO("imx046", IMX046_I2C_ADDR), > + .platform_data = &sdp3430_imx046_platform_data, > + }, > +#endif > }; > > static int __init omap3430_i2c_init(void) > > -- > video4linux-list mailing list > Unsubscribe mailto:video4linux-list- > request@xxxxxxxxxx?subject=unsubscribe > https://www.redhat.com/mailman/listinfo/video4linux-list -- To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html