On 09/24/2013 03:53 AM, Roger Quadros wrote: > Provide RESET GPIO and Power regulator for the USB PHY, > the USB Host port mode and the PHY device for the controller. > Also provide pin multiplexer information for USB host pins. > > We also relocate omap3_pmx_core pin definations so that they > are close to omap3_pmx_wkup pin definations. > > Signed-off-by: Roger Quadros <rogerq@xxxxxx> > --- just using this thread, but a question -> I am kernel * master dec8e46 Merge tag 'arc-v3.13-rc1-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc and I see that VAUX2 which supplies USB_1V8[1] is not enabled -> I did a quick patch and it did seem to work (Usb keyboard, networking, mouse etc on my ehci ports seems to come up good) - any suggestions how we'd like to handle this? --- a/arch/arm/boot/dts/omap3-beagle-xm.dts +++ b/arch/arm/boot/dts/omap3-beagle-xm.dts @@ -169,6 +169,14 @@ bus-width = <8>; }; +&vaux2 { + regulator-name = "HubPower"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; +}; + + [1] https://github.com/CircuitCo/BeagleBoard-xM-RevC/blob/master/BeagleBoard-xM_revC_SCH.pdf?raw=true > arch/arm/boot/dts/omap3-beagle-xm.dts | 65 ++++++++++++++++++++++++++++----- > 1 files changed, 56 insertions(+), 9 deletions(-) > > diff --git a/arch/arm/boot/dts/omap3-beagle-xm.dts b/arch/arm/boot/dts/omap3-beagle-xm.dts > index afdb164..b081f5a 100644 > --- a/arch/arm/boot/dts/omap3-beagle-xm.dts > +++ b/arch/arm/boot/dts/omap3-beagle-xm.dts > @@ -69,6 +69,23 @@ > }; > > }; > + > + /* HS USB Port 2 Power */ > + hsusb2_power: hsusb2_power_reg { > + compatible = "regulator-fixed"; > + regulator-name = "hsusb2_vbus"; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + gpio = <&twl_gpio 18 0>; /* GPIO LEDA */ > + startup-delay-us = <70000>; > + }; > + > + /* HS USB Host PHY on PORT 2 */ > + hsusb2_phy: hsusb2_phy { > + compatible = "usb-nop-xceiv"; > + reset-gpios = <&gpio5 19 GPIO_ACTIVE_LOW>; /* gpio_147 */ > + vcc-supply = <&hsusb2_power>; > + }; > }; > > &omap3_pmx_wkup { > @@ -79,6 +96,37 @@ > }; > }; > > +&omap3_pmx_core { > + pinctrl-names = "default"; > + pinctrl-0 = < > + &hsusbb2_pins > + >; > + > + uart3_pins: pinmux_uart3_pins { > + pinctrl-single,pins = < > + 0x16e (PIN_INPUT | PIN_OFF_WAKEUPENABLE | MUX_MODE0) /* uart3_rx_irrx.uart3_rx_irrx */ > + 0x170 (PIN_OUTPUT | MUX_MODE0) /* uart3_tx_irtx.uart3_tx_irtx OUTPUT | MODE0 */ > + >; > + }; > + > + hsusbb2_pins: pinmux_hsusbb2_pins { > + pinctrl-single,pins = < > + 0x5c0 (PIN_OUTPUT | MUX_MODE3) /* etk_d10.hsusb2_clk */ > + 0x5c2 (PIN_OUTPUT | MUX_MODE3) /* etk_d11.hsusb2_stp */ > + 0x5c4 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d12.hsusb2_dir */ > + 0x5c6 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d13.hsusb2_nxt */ > + 0x5c8 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d14.hsusb2_data0 */ > + 0x5cA (PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d15.hsusb2_data1 */ > + 0x1a4 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi1_cs3.hsusb2_data2 */ > + 0x1a6 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_clk.hsusb2_data7 */ > + 0x1a8 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_simo.hsusb2_data4 */ > + 0x1aa (PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_somi.hsusb2_data5 */ > + 0x1ac (PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_cs0.hsusb2_data6 */ > + 0x1ae (PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_cs1.hsusb2_data3 */ > + >; > + }; > +}; > + > &i2c1 { > clock-frequency = <2600000>; > > @@ -148,15 +196,6 @@ > power = <50>; > }; > > -&omap3_pmx_core { > - uart3_pins: pinmux_uart3_pins { > - pinctrl-single,pins = < > - 0x16e (PIN_INPUT | PIN_OFF_WAKEUPENABLE | MUX_MODE0) /* uart3_rx_irrx.uart3_rx_irrx */ > - 0x170 (PIN_OUTPUT | MUX_MODE0) /* uart3_tx_irtx.uart3_tx_irtx OUTPUT | MODE0 */ > - >; > - }; > -}; > - > &uart3 { > pinctrl-names = "default"; > pinctrl-0 = <&uart3_pins>; > @@ -166,3 +205,11 @@ > pinctrl-names = "default"; > pinctrl-0 = <&gpio1_pins>; > }; > + > +&usbhshost { > + port2-mode = "ehci-phy"; > +}; > + > +&usbhsehci { > + phys = <0 &hsusb2_phy>; > +}; > -- Regards, Nishanth Menon -- To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html