This patch contains some fixes for the 1.8V MMC2 interface on the OMAP
2430/3430 that I had submitted for comment in a previous patch, this time
leaving out the device configuration in deference to the other patch submitted
for this purpose (once it has been resubmitted). These fixes were necessary
for me to use MMC2 with an OMAP2430. I don't know about applicability to the
3430 however, thus I am sending again for comment.
Cheers,
Seth
diff --git a/drivers/mmc/host/omap_hsmmc.c b/drivers/mmc/host/omap_hsmmc.c
index 248257f..d5d82a8 100644
--- a/drivers/mmc/host/omap_hsmmc.c
+++ b/drivers/mmc/host/omap_hsmmc.c
@@ -388,8 +388,12 @@ static int omap_mmc_switch_opcond(struct mmc_omap_host *host, int vdd)
* If a MMC dual voltage card is detected, the set_ios fn calls
* this fn with VDD bit set for 1.8V. Upon card removal from the
* slot, mmc_omap_detect fn sets the VDD back to 3V.
+ *
+ * Only MMC1 supports 3.0V. MMC2 will not function if SDVS30 is
+ * set in HCTL.
*/
- if (((1 << vdd) == MMC_VDD_32_33) || ((1 << vdd) == MMC_VDD_33_34))
+ if (host->id == OMAP_MMC1_DEVID && (((1 << vdd) == MMC_VDD_32_33) ||
+ ((1 << vdd) == MMC_VDD_33_34)))
reg_val |= SDVS30;
if ((1 << vdd) == MMC_VDD_165_195)
reg_val |= SDVS18;
@@ -517,10 +521,16 @@ mmc_omap_start_dma_transfer(struct mmc_omap_host *host, struct mmc_request *req)
if (!(data->flags & MMC_DATA_WRITE)) {
host->dma_dir = DMA_FROM_DEVICE;
- sync_dev = OMAP24XX_DMA_MMC1_RX;
+ if (host->id == OMAP_MMC1_DEVID)
+ sync_dev = OMAP24XX_DMA_MMC1_RX;
+ else
+ sync_dev = OMAP24XX_DMA_MMC2_RX;
} else {
host->dma_dir = DMA_TO_DEVICE;
- sync_dev = OMAP24XX_DMA_MMC1_TX;
+ if (host->id == OMAP_MMC1_DEVID)
+ sync_dev = OMAP24XX_DMA_MMC1_TX;
+ else
+ sync_dev = OMAP24XX_DMA_MMC2_TX;
}
ret = omap_request_dma(sync_dev, "MMC/SD", mmc_omap_dma_cb,
@@ -692,6 +702,7 @@ static int __init omap_mmc_probe(struct platform_device *pdev)
struct mmc_omap_host *host = NULL;
struct resource *res;
int ret = 0, irq;
+ u32 hctl, capa;
if (pdata == NULL) {
dev_err(&pdev->dev, "Platform Data is missing\n");
@@ -778,11 +789,20 @@ static int __init omap_mmc_probe(struct platform_device *pdev)
if (pdata->conf.wire4)
mmc->caps |= MMC_CAP_4_BIT_DATA;
+ /* Only MMC1 supports 3.0V */
+ if (host->id == OMAP_MMC1_DEVID) {
+ hctl = SDVS30;
+ capa = VS30 | VS18;
+ } else {
+ hctl = SDVS18;
+ capa = VS18;
+ }
+
OMAP_HSMMC_WRITE(host->base, HCTL,
- OMAP_HSMMC_READ(host->base, HCTL) | SDVS30);
+ OMAP_HSMMC_READ(host->base, HCTL) | hctl);
- OMAP_HSMMC_WRITE(host->base, CAPA, OMAP_HSMMC_READ(host->base,
- CAPA) | VS30 | VS18);
+ OMAP_HSMMC_WRITE(host->base, CAPA,
+ OMAP_HSMMC_READ(host->base, CAPA) | capa);
/* Set the controller to AUTO IDLE mode */
OMAP_HSMMC_WRITE(host->base, SYSCONFIG,
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
