This patch adds OMAP EHCI glue layer and Menu config option
Incorporated Paul Walmsley review comments on usage of cm_{read,write}_mod_reg()
Signed-off-by: Vikram Pandita <vikram.pandita@xxxxxx>
Acked-by: Kamat, Nishant <nskamat@xxxxxx>
---
drivers/usb/Kconfig | 1
drivers/usb/host/Kconfig | 19 +
drivers/usb/host/ehci-hcd.c | 5
drivers/usb/host/ehci-omap.c | 560 +++++++++++++++++++++++++++++++++++++++++++
drivers/usb/host/ehci-omap.h | 116 ++++++++
5 files changed, 701 insertions(+)
Index: omap-submit/drivers/usb/host/ehci-omap.c
===================================================================
--- /dev/null 1970-01-01 00:00:00.000000000 +0000
+++ omap-submit/drivers/usb/host/ehci-omap.c 2008-02-04 17:07:14.000000000 +0530
@@ -0,0 +1,560 @@
+/*
+ * ehci-omap.c - driver for USBHOST on OMAP 34xx processor
+ *
+ * Bus Glue for OMAP34xx USBHOST 3 port EHCI controller
+ * Tested on OMAP3430 ES2.0 SDP
+ *
+ * Copyright (C) 2007-2008 Texas Instruments, Inc.
+ * Copyright (C) 2007-2008 Vikram Pandita <vikram.pandita@xxxxxx>
+ * Based on "ehci-fsl.c" by David Brownell and
+ * "ehci-au1xxx.c" by K.Boge <karsten.boge@xxxxxxx>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ *
+ */
+
+#include <linux/platform_device.h>
+#include <linux/clk.h>
+#include <asm/arch/gpio.h>
+
+#include "ehci-omap.h"
+
+
+#ifdef CONFIG_OMAP_EHCI_PHY_MODE
+/* EHCI connected to External PHY */
+
+/* External USB connectivity board: 750-2083-001
+ * Connected to OMAP3430 SDP
+ * The board has Port1 and Port2 connected to ISP1504 in 12-pin ULPI mode
+ */
+
+/* ISSUE1:
+ * ISP1504 for input clocking mode needs special reset handling
+ * Hold the PHY in reset by asserting RESET_N signal
+ * Then start the 60Mhz clock input to PHY
+ * Release the reset after a delay -
+ * to get the PHY state machine in working state
+ */
+#define EXTERNAL_PHY_RESET
+#define EXT_PHY_RESET_GPIO_PORT1 (57)
+#define EXT_PHY_RESET_GPIO_PORT2 (61)
+#define EXT_PHY_RESET_DELAY (10)
+
+/* ISSUE2:
+ * USBHOST supports External charge pump PHYs only
+ * Use the VBUS from Port1 to power VBUS of Port2 externally
+ * So use Port2 as the working ULPI port
+ */
+#define VBUS_INTERNAL_CHARGEPUMP_HACK
+
+#endif /* CONFIG_OMAP_EHCI_PHY_MODE */
+
+/*-------------------------------------------------------------------------*/
+
+/* Define USBHOST clocks for clock management */
+struct ehci_omap_clock_defs {
+ struct clk *usbhost_ick_clk;
+ struct clk *usbhost2_120m_fck_clk;
+ struct clk *usbhost1_48m_fck_clk;
+ struct clk *usbtll_fck_clk;
+ struct clk *usbtll_ick_clk;
+};
+
+/* Clock names as per clock framework: May change so keep as #defs */
+#define USBHOST_ICKL "usbhost_l4_ick"
+#define USBHOST_120M_FCLK "usbhost_120m_fck"
+#define USBHOST_48M_FCLK "usbhost_48m_fck"
+#define USBHOST_TLL_ICKL "usbtll_ick"
+#define USBHOST_TLL_FCLK "usbtll_fck"
+/*-------------------------------------------------------------------------*/
+
+/* omap_start_ehc
+ * - Start the TI USBHOST controller
+ */
+static int omap_start_ehc(struct platform_device *dev, struct usb_hcd *hcd)
+{
+ struct ehci_omap_clock_defs *ehci_clocks;
+
+ dev_dbg(hcd->self.controller, ": starting TI EHCI USB Controller\n");
+
+ ehci_clocks = (struct ehci_omap_clock_defs *)(
+ ((char *)hcd_to_ehci(hcd)) +
+ sizeof(struct ehci_hcd));
+
+ /* Start DPLL5 Programming:
+ * Clock Framework is not doing this now:
+ * This will be done in clock framework later
+ */
+ /* Enable DPLL 5 : Based on Input of 13Mhz*/
+ cm_write_mod_reg((12 << OMAP3430ES2_PERIPH2_DPLL_DIV_SHIFT)|
+ (120 << OMAP3430ES2_PERIPH2_DPLL_MULT_SHIFT),
+ PLL_MOD, OMAP3430ES2_CM_CLKSEL4);
+
+ cm_write_mod_reg(1 << OMAP3430ES2_DIV_120M_SHIFT,
+ PLL_MOD, OMAP3430ES2_CM_CLKSEL5);
+
+ cm_write_mod_reg((7 << OMAP3430ES2_PERIPH2_DPLL_FREQSEL_SHIFT) |
+ (7 << OMAP3430ES2_EN_PERIPH2_DPLL_SHIFT),
+ PLL_MOD, OMAP3430ES2_CM_CLKEN2);
+
+ while (!(cm_read_mod_reg(PLL_MOD, CM_IDLEST2) &
+ OMAP3430_ST_PERIPH2_CLK))
+ dev_dbg(hcd->self.controller,
+ "idlest2 = 0x%x\n",
+ cm_read_mod_reg(PLL_MOD, CM_IDLEST2));
+ /* End DPLL5 programming */
+
+
+ /* PRCM settings for USBHOST:
+ * Interface clk un-related to domain transition
+ */
+ cm_write_mod_reg(0 << OMAP3430ES2_AUTO_USBHOST_SHIFT,
+ OMAP3430ES2_USBHOST_MOD, CM_AUTOIDLE);
+
+ /* Disable sleep dependency with MPU and IVA */
+ cm_write_mod_reg((0 << OMAP3430ES2_EN_MPU_SHIFT) |
+ (0 << OMAP3430ES2_EN_IVA2_SHIFT),
+ OMAP3430ES2_USBHOST_MOD, OMAP3430_CM_SLEEPDEP);
+
+ /* Disable Automatic transition of clock */
+ cm_write_mod_reg(0 << OMAP3430ES2_CLKTRCTRL_USBHOST_SHIFT,
+ OMAP3430ES2_USBHOST_MOD, CM_CLKSTCTRL);
+
+ /* Enable Clocks for USBHOST */
+ ehci_clocks->usbhost_ick_clk = clk_get(&dev->dev,
+ USBHOST_ICKL);
+ if (IS_ERR(ehci_clocks->usbhost_ick_clk))
+ return PTR_ERR(ehci_clocks->usbhost_ick_clk);
+ clk_enable(ehci_clocks->usbhost_ick_clk);
+
+
+ ehci_clocks->usbhost2_120m_fck_clk = clk_get(&dev->dev,
+ USBHOST_120M_FCLK);
+ if (IS_ERR(ehci_clocks->usbhost2_120m_fck_clk))
+ return PTR_ERR(ehci_clocks->usbhost2_120m_fck_clk);
+ clk_enable(ehci_clocks->usbhost2_120m_fck_clk);
+
+ ehci_clocks->usbhost1_48m_fck_clk = clk_get(&dev->dev,
+ USBHOST_48M_FCLK);
+ if (IS_ERR(ehci_clocks->usbhost1_48m_fck_clk))
+ return PTR_ERR(ehci_clocks->usbhost1_48m_fck_clk);
+ clk_enable(ehci_clocks->usbhost1_48m_fck_clk);
+
+
+#ifdef EXTERNAL_PHY_RESET
+ /* Refer: ISSUE1 */
+ omap_request_gpio(EXT_PHY_RESET_GPIO_PORT1);
+ omap_set_gpio_direction(EXT_PHY_RESET_GPIO_PORT1, 0);
+ omap_request_gpio(EXT_PHY_RESET_GPIO_PORT2);
+ omap_set_gpio_direction(EXT_PHY_RESET_GPIO_PORT2, 0);
+ omap_set_gpio_dataout(EXT_PHY_RESET_GPIO_PORT1, 0);
+ omap_set_gpio_dataout(EXT_PHY_RESET_GPIO_PORT2, 0);
+ /* Hold the PHY in RESET for enough time till DIR is high */
+ udelay(EXT_PHY_RESET_DELAY);
+#endif
+
+ /* Configure TLL for 60Mhz clk for ULPI */
+ ehci_clocks->usbtll_fck_clk = clk_get(&dev->dev, USBHOST_TLL_FCLK);
+ if (IS_ERR(ehci_clocks->usbtll_fck_clk))
+ return PTR_ERR(ehci_clocks->usbtll_fck_clk);
+ clk_enable(ehci_clocks->usbtll_fck_clk);
+
+ ehci_clocks->usbtll_ick_clk = clk_get(&dev->dev, USBHOST_TLL_ICKL);
+ if (IS_ERR(ehci_clocks->usbtll_ick_clk))
+ return PTR_ERR(ehci_clocks->usbtll_ick_clk);
+ clk_enable(ehci_clocks->usbtll_ick_clk);
+
+ /* Disable Auto Idle of USBTLL */
+ cm_write_mod_reg((0 << OMAP3430_AUTO_USBTLL_SHIFT),
+ CORE_MOD, OMAP3430_CM_AUTOIDLE3_CORE);
+
+ /* Wait for TLL to be Active */
+ while ((cm_read_mod_reg(CORE_MOD, OMAP3430_CM_IDLEST3_CORE) &
+ (1 << OMAP3430_ST_USBTLL_SHIFT)));
+
+ /* perform TLL soft reset, and wait until reset is complete */
+ /* (1<<3) = no idle mode only for initial debugging */
+ omap_writel((1 << OMAP_USBTLL_SYSCONFIG_SOFTRESET_SHIFT) |
+ (1 << OMAP_USBTLL_SYSCONFIG_ENAWAKEUP_SHIFT) |
+ (1 << OMAP_USBTLL_SYSCONFIG_SIDLEMODE_SHIFT) |
+ (1 << OMAP_USBTLL_SYSCONFIG_CACTIVITY_SHIFT),
+ OMAP_USBTLL_SYSCONFIG);
+ /* Wait for TLL reset to complete */
+ while (!(omap_readl(OMAP_USBTLL_SYSSTATUS) &
+ (1 << OMAP_USBTLL_SYSSTATUS_RESETDONE_SHIFT)));
+
+ dev_dbg(hcd->self.controller, "\n TLL RESET DONE");
+
+ /* Put UHH in NoIdle/NoStandby mode */
+ omap_writel((0 << OMAP_UHH_SYSCONFIG_AUTOIDLE_SHIFT) |
+ (1 << OMAP_UHH_SYSCONFIG_ENAWAKEUP_SHIFT) |
+ (1 << OMAP_UHH_SYSCONFIG_SIDLEMODE_SHIFT) |
+ (1 << OMAP_UHH_SYSCONFIG_CACTIVITY_SHIFT) |
+ (1 << OMAP_UHH_SYSCONFIG_MIDLEMODE_SHIFT),
+ OMAP_UHH_SYSCONFIG);
+
+#ifdef CONFIG_OMAP_EHCI_PHY_MODE
+ /* Bypass the TLL module for PHY mode operation */
+ omap_writel((0 << OMAP_UHH_HOSTCONFIG_ULPI_BYPASS_SHIFT),
+ OMAP_UHH_HOSTCONFIG);
+ /* Ensure that BYPASS is set */
+ while (omap_readl(OMAP_UHH_HOSTCONFIG) &
+ (1 << OMAP_UHH_HOSTCONFIG_ULPI_BYPASS_SHIFT));
+
+ dev_dbg(hcd->self.controller, "Entered ULPI PHY MODE: success");
+
+#else
+ /* Use UTMI Ports of TLL */
+ omap_writel((1 << OMAP_UHH_HOSTCONFIG_ULPI_BYPASS_SHIFT),
+ OMAP_UHH_HOSTCONFIG);
+ /* Enusre bit is set */
+ while (!(omap_readl(OMAP_UHH_HOSTCONFIG) &
+ (1 << OMAP_UHH_HOSTCONFIG_ULPI_BYPASS_SHIFT)));
+
+ dev_dbg(hcd->self.controller, "Entered UTMI MODE: success");
+
+ /* Program the 3 TLL channels upfront */
+
+ /* CHANNEL-1 */
+ /* Disable AutoIdle */
+ omap_writel(omap_readl(OMAP_TLL_CHANNEL_CONF(0)) &
+ ~(1<<OMAP_TLL_CHANNEL_CONF_UTMIAUTOIDLE_SHIFT),
+ OMAP_TLL_CHANNEL_CONF(0));
+ /* Disable BitStuffing */
+ omap_writel(omap_readl(OMAP_TLL_CHANNEL_CONF(0)) &
+ ~(1<<OMAP_TLL_CHANNEL_CONF_ULPINOBITSTUFF_SHIFT),
+ OMAP_TLL_CHANNEL_CONF(0));
+ /* SDR Mode */
+ omap_writel(omap_readl(OMAP_TLL_CHANNEL_CONF(0)) &
+ ~(1<<OMAP_TLL_CHANNEL_CONF_ULPIDDRMODE_SHIFT),
+ OMAP_TLL_CHANNEL_CONF(0));
+
+ /* CHANNEL-2 */
+ /* Disable AutoIdle */
+ omap_writel(omap_readl(OMAP_TLL_CHANNEL_CONF(1)) &
+ ~(1<<OMAP_TLL_CHANNEL_CONF_UTMIAUTOIDLE_SHIFT),
+ OMAP_TLL_CHANNEL_CONF(1));
+ /* Disable BitStuffing */
+ omap_writel(omap_readl(OMAP_TLL_CHANNEL_CONF(1)) &
+ ~(1<<OMAP_TLL_CHANNEL_CONF_ULPINOBITSTUFF_SHIFT),
+ OMAP_TLL_CHANNEL_CONF(1));
+ /* SDR Mode */
+ omap_writel(omap_readl(OMAP_TLL_CHANNEL_CONF(1)) &
+ ~(1<<OMAP_TLL_CHANNEL_CONF_ULPIDDRMODE_SHIFT),
+ OMAP_TLL_CHANNEL_CONF(1));
+
+ /* CHANNEL-3 */
+ /* Disable AutoIdle */
+ omap_writel(omap_readl(OMAP_TLL_CHANNEL_CONF(2)) &
+ ~(1<<OMAP_TLL_CHANNEL_CONF_UTMIAUTOIDLE_SHIFT),
+ OMAP_TLL_CHANNEL_CONF(2));
+ /* Disable BitStuffing */
+ omap_writel(omap_readl(OMAP_TLL_CHANNEL_CONF(2)) &
+ ~(1<<OMAP_TLL_CHANNEL_CONF_ULPINOBITSTUFF_SHIFT),
+ OMAP_TLL_CHANNEL_CONF(2));
+ /* SDR Mode */
+ omap_writel(omap_readl(OMAP_TLL_CHANNEL_CONF(2)) &
+ ~(1<<OMAP_TLL_CHANNEL_CONF_ULPIDDRMODE_SHIFT),
+ OMAP_TLL_CHANNEL_CONF(2));
+
+ /* Program Common TLL register */
+ omap_writel((1 << OMAP_TLL_SHARED_CONF_FCLK_IS_ON_SHIFT) |
+ (1 << OMAP_TLL_SHARED_CONF_USB_DIVRATION_SHIFT) |
+ (1 << OMAP_TLL_SHARED_CONF_USB_180D_SDR_EN_SHIFT) |
+ (1 << OMAP_TLL_SHARED_CONF_USB_90D_DDR_EN_SHFT),
+ OMAP_TLL_SHARED_CONF);
+
+ /* Enable All 3 channels now */
+ omap_writel(omap_readl(OMAP_TLL_CHANNEL_CONF(0)) |
+ (1<<OMAP_TLL_CHANNEL_CONF_CHANEN_SHIFT),
+ OMAP_TLL_CHANNEL_CONF(0));
+
+ omap_writel(omap_readl(OMAP_TLL_CHANNEL_CONF(1)) |
+ (1<<OMAP_TLL_CHANNEL_CONF_CHANEN_SHIFT),
+ OMAP_TLL_CHANNEL_CONF(1));
+
+ omap_writel(omap_readl(OMAP_TLL_CHANNEL_CONF(2)) |
+ (1<<OMAP_TLL_CHANNEL_CONF_CHANEN_SHIFT),
+ OMAP_TLL_CHANNEL_CONF(2));
+
+ /* test writing to ulpi scratch register */
+ omap_writeb(0xBE, OMAP_TLL_ULPI_SCRATCH_REGISTER);
+ dev_dbg(hcd->self.controller, "\nULPI_SCRATCH_REG 0x%02x\n",
+ omap_readb(OMAP_TLL_ULPI_SCRATCH_REGISTER));
+
+#endif
+
+#ifdef EXTERNAL_PHY_RESET
+ /* Refer ISSUE1:
+ * Hold the PHY in RESET for enough time till PHY is settled and ready
+ */
+ udelay(EXT_PHY_RESET_DELAY);
+ omap_set_gpio_dataout(EXT_PHY_RESET_GPIO_PORT1, 1);
+ omap_set_gpio_dataout(EXT_PHY_RESET_GPIO_PORT2, 1);
+#endif
+
+#ifdef VBUS_INTERNAL_CHARGEPUMP_HACK
+ /* Refer ISSUE2: LINK assumes external charge pump */
+
+ /* use Port1 VBUS to charge externally Port2:
+ * So for PHY mode operation use Port2 only
+ */
+ omap_writel((0xA << EHCI_INSNREG05_ULPI_REGADD_SHIFT) |/* OTG ctrl reg*/
+ (2 << EHCI_INSNREG05_ULPI_OPSEL_SHIFT) |/* Write */
+ (1 << EHCI_INSNREG05_ULPI_PORTSEL_SHIFT) |/* Port1 */
+ (1 << EHCI_INSNREG05_ULPI_CONTROL_SHIFT) |/* Start */
+ (0x26),
+ EHCI_INSNREG05_ULPI);
+
+ while (!(omap_readl(EHCI_INSNREG05_ULPI) &
+ (1<<EHCI_INSNREG05_ULPI_CONTROL_SHIFT)));
+
+#endif
+
+ return 0;
+}
+
+/*-------------------------------------------------------------------------*/
+
+static void omap_stop_ehc(struct platform_device *dev, struct usb_hcd *hcd)
+{
+ struct ehci_omap_clock_defs *ehci_clocks;
+
+ ehci_clocks = (struct ehci_omap_clock_defs *)
+ (((char *)hcd_to_ehci(hcd)) + sizeof(struct ehci_hcd));
+
+ dev_dbg(hcd->self.controller, ": stopping TI EHCI USB Controller\n");
+
+ /* Reset OMAP modules for insmod/rmmod to work */
+ omap_writel((1<<1), OMAP_UHH_SYSCONFIG);
+ while (!(omap_readl(OMAP_UHH_SYSSTATUS) & (1<<0)));
+ while (!(omap_readl(OMAP_UHH_SYSSTATUS) & (1<<1)));
+ while (!(omap_readl(OMAP_UHH_SYSSTATUS) & (1<<2)));
+ dev_dbg(hcd->self.controller,
+ "UHH RESET DONE OMAP_UHH_SYSSTATUS %x !!\n",
+ omap_readl(OMAP_UHH_SYSSTATUS));
+
+ omap_writel((1<<1), OMAP_USBTLL_SYSCONFIG);
+ while (!(omap_readl(OMAP_USBTLL_SYSSTATUS) & (1<<0)));
+ dev_dbg(hcd->self.controller, ":TLL RESEET DONE");
+
+ if (ehci_clocks->usbtll_fck_clk != NULL) {
+ clk_disable(ehci_clocks->usbtll_fck_clk);
+ clk_put(ehci_clocks->usbtll_fck_clk);
+ ehci_clocks->usbtll_fck_clk = NULL;
+ }
+
+ if (ehci_clocks->usbhost_ick_clk != NULL) {
+ clk_disable(ehci_clocks->usbhost_ick_clk);
+ clk_put(ehci_clocks->usbhost_ick_clk);
+ ehci_clocks->usbhost_ick_clk = NULL;
+ }
+
+ if (ehci_clocks->usbhost1_48m_fck_clk != NULL) {
+ clk_disable(ehci_clocks->usbhost1_48m_fck_clk);
+ clk_put(ehci_clocks->usbhost1_48m_fck_clk);
+ ehci_clocks->usbhost1_48m_fck_clk = NULL;
+ }
+
+ if (ehci_clocks->usbhost2_120m_fck_clk != NULL) {
+ clk_disable(ehci_clocks->usbhost2_120m_fck_clk);
+ clk_put(ehci_clocks->usbhost2_120m_fck_clk);
+ ehci_clocks->usbhost2_120m_fck_clk = NULL;
+ }
+
+ if (ehci_clocks->usbtll_ick_clk != NULL) {
+ clk_disable(ehci_clocks->usbtll_ick_clk);
+ clk_put(ehci_clocks->usbtll_ick_clk);
+ ehci_clocks->usbtll_ick_clk = NULL;
+ }
+
+
+#ifdef EXTERNAL_PHY_RESET
+ omap_free_gpio(EXT_PHY_RESET_GPIO_PORT1);
+ omap_free_gpio(EXT_PHY_RESET_GPIO_PORT2);
+#endif
+
+ dev_dbg(hcd->self.controller,
+ ": Clock to USB host has been disabled\n");
+}
+
+/*-------------------------------------------------------------------------*/
+/* Forward declaration */
+extern const struct hc_driver ehci_omap_hc_driver;
+
+/*-------------------------------------------------------------------------*/
+/* configure so an HC device and id are always provided */
+/* always called with process context; sleeping is OK */
+
+/**
+ * ehci_hcd_omap_drv_probe - initialize TI-based HCDs
+ * Context: !in_interrupt()
+ *
+ * Allocates basic resources for this USB host controller, and
+ * then invokes the start() method for the HCD associated with it
+ * through the hotplug entry's driver_data.
+ *
+ */
+static int ehci_hcd_omap_drv_probe(struct platform_device *dev)
+{
+ int retval = 0;
+ struct usb_hcd *hcd;
+ struct ehci_hcd *ehci;
+
+ dev_dbg(&dev->dev, "ehci_hcd_omap_drv_probe()");
+
+ if (usb_disabled())
+ return -ENODEV;
+
+ if (dev->resource[1].flags != IORESOURCE_IRQ) {
+ dev_dbg(&dev->dev, "resource[1] is not IORESOURCE_IRQ");
+ retval = -ENOMEM;
+ }
+
+ hcd = usb_create_hcd(&ehci_omap_hc_driver, &dev->dev, dev->dev.bus_id);
+ if (!hcd)
+ return -ENOMEM;
+
+ retval = omap_start_ehc(dev, hcd);
+ if (retval)
+ return retval;
+
+ hcd->rsrc_start = 0;
+ hcd->rsrc_len = 0;
+ hcd->rsrc_start = dev->resource[0].start;
+ hcd->rsrc_len = dev->resource[0].end - dev->resource[0].start + 1;
+
+ hcd->regs = (void __iomem *) (int) IO_ADDRESS(hcd->rsrc_start);
+
+ ehci = hcd_to_ehci(hcd);
+ ehci->caps = hcd->regs;
+
+ ehci->regs = hcd->regs + HC_LENGTH(readl(&ehci->caps->hc_capbase));
+ /* cache this readonly data; minimize chip reads */
+ ehci->hcs_params = readl(&ehci->caps->hcs_params);
+
+ /* SET 1 micro-frame Interrupt interval */
+ writel(readl(&ehci->regs->command) | (1<<16), &ehci->regs->command);
+
+ retval = usb_add_hcd(hcd, dev->resource[1].start,
+ IRQF_DISABLED | IRQF_SHARED);
+ if (retval == 0)
+ return retval;
+
+ dev_dbg(hcd->self.controller, "ERR: add_hcd");
+ omap_stop_ehc(dev, hcd);
+
+ usb_put_hcd(hcd);
+ return retval;
+}
+
+/*-------------------------------------------------------------------------*/
+
+/* may be called without controller electrically present */
+/* may be called with controller, bus, and devices active */
+
+/**
+ * ehci_hcd_omap_drv_remove - shutdown processing for EHCI HCDs
+ * @dev: USB Host Controller being removed
+ * Context: !in_interrupt()
+ *
+ * Reverses the effect of usb_ehci_hcd_omap_probe(), first invoking
+ * the HCD's stop() method. It is always called from a thread
+ * context, normally "rmmod", "apmd", or something similar.
+ *
+ */
+static int ehci_hcd_omap_drv_remove(struct platform_device *dev)
+{
+ struct usb_hcd *hcd = platform_get_drvdata(dev);
+
+ dev_dbg(&dev->dev, "ehci_hcd_omap_drv_remove()");
+
+ usb_remove_hcd(hcd);
+ usb_put_hcd(hcd);
+ omap_stop_ehc(dev, hcd);
+
+ return 0;
+}
+
+/*-------------------------------------------------------------------------*/
+#ifdef CONFIG_PM
+static int omap_ehci_bus_suspend(struct usb_hcd *hcd)
+{
+ return ehci_bus_suspend(hcd);
+}
+
+static int omap_ehci_bus_resume(struct usb_hcd *hcd)
+{
+ return ehci_bus_resume(hcd);
+}
+#endif
+/*-------------------------------------------------------------------------*/
+
+const struct hc_driver ehci_omap_hc_driver = {
+ .description = hcd_name,
+ .product_desc = "OMAP-EHCI Host Controller",
+ .hcd_priv_size = sizeof(struct ehci_hcd)
+ + sizeof(struct ehci_omap_clock_defs),
+
+ /*
+ * generic hardware linkage
+ */
+ .irq = ehci_irq,
+ .flags = HCD_MEMORY | HCD_USB2,
+
+ /*
+ * basic lifecycle operations
+ */
+ .reset = ehci_init,
+ .start = ehci_run,
+ .stop = ehci_stop,
+ .shutdown = ehci_shutdown,
+
+ /*
+ * managing i/o requests and associated device resources
+ */
+ .urb_enqueue = ehci_urb_enqueue,
+ .urb_dequeue = ehci_urb_dequeue,
+ .endpoint_disable = ehci_endpoint_disable,
+
+ /*
+ * scheduling support
+ */
+ .get_frame_number = ehci_get_frame,
+
+ /*
+ * root hub support
+ */
+ .hub_status_data = ehci_hub_status_data,
+ .hub_control = ehci_hub_control,
+#ifdef CONFIG_PM
+ .bus_suspend = omap_ehci_bus_suspend,
+ .bus_resume = omap_ehci_bus_resume,
+#endif
+};
+
+/*-------------------------------------------------------------------------*/
+MODULE_ALIAS("omap-ehci");
+static struct platform_driver ehci_hcd_omap_driver = {
+ .probe = ehci_hcd_omap_drv_probe,
+ .remove = ehci_hcd_omap_drv_remove,
+ .shutdown = usb_hcd_platform_shutdown,
+ /*.suspend = ehci_hcd_omap_drv_suspend, */
+ /*.resume = ehci_hcd_omap_drv_resume, */
+ .driver = {
+ .name = "ehci-omap",
+ .bus = &platform_bus_type
+ }
+};
Index: omap-submit/drivers/usb/host/ehci-hcd.c
===================================================================
--- omap-submit.orig/drivers/usb/host/ehci-hcd.c 2008-02-04 17:06:27.000000000 +0530
+++ omap-submit/drivers/usb/host/ehci-hcd.c 2008-02-04 17:07:14.000000000 +0530
@@ -954,6 +954,11 @@
#define PLATFORM_DRIVER ehci_hcd_au1xxx_driver
#endif
+#ifdef CONFIG_ARCH_OMAP34XX
+#include "ehci-omap.c"
+#define PLATFORM_DRIVER ehci_hcd_omap_driver
+#endif
+
#ifdef CONFIG_PPC_PS3
#include "ehci-ps3.c"
#define PS3_SYSTEM_BUS_DRIVER ps3_ehci_driver
Index: omap-submit/drivers/usb/host/ehci-omap.h
===================================================================
--- /dev/null 1970-01-01 00:00:00.000000000 +0000
+++ omap-submit/drivers/usb/host/ehci-omap.h 2008-02-04 17:07:14.000000000 +0530
@@ -0,0 +1,116 @@
+/*
+ * ehci-omap.h - register definitions for USBHOST in OMAP 34xx
+ *
+ * Copyright (C) 2007-2008 Texas Instruments, Inc.
+ * Copyright (C) 2007-2008 Vikram Pandita <vikram.pandita@xxxxxx>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ *
+ */
+
+#ifndef __EHCI_OMAP_H
+#define __EHCI_OMAP_H
+
+#include <asm/hardware.h>
+#include "../../../arch/arm/mach-omap2/cm.h"
+#include "../../../arch/arm/mach-omap2/cm_regbits_34xx.h"
+
+/*
+ * OMAP USBHOST Register addresses: PHYSICAL ADDRESSES
+ * Use omap_readl()/omap_writel() functions
+ */
+
+/* USBHOST: TLL, UUH, OHCI, EHCI */
+#define OMAP_USBHOST_BASE (L4_34XX_BASE + 0x60000)
+
+/* TLL Register Set */
+#define OMAP_USBHOST_TLL_BASE (OMAP_USBHOST_BASE + 0x2000)
+#define OMAP_USBTLL_REVISION (OMAP_USBHOST_TLL_BASE + 0x00)
+#define OMAP_USBTLL_SYSCONFIG (OMAP_USBHOST_TLL_BASE + 0x10)
+ #define OMAP_USBTLL_SYSCONFIG_CACTIVITY_SHIFT 8
+ #define OMAP_USBTLL_SYSCONFIG_SIDLEMODE_SHIFT 3
+ #define OMAP_USBTLL_SYSCONFIG_ENAWAKEUP_SHIFT 2
+ #define OMAP_USBTLL_SYSCONFIG_SOFTRESET_SHIFT 1
+ #define OMAP_USBTLL_SYSCONFIG_AUTOIDLE_SHIFT 0
+#define OMAP_USBTLL_SYSSTATUS (OMAP_USBHOST_TLL_BASE + 0x14)
+ #define OMAP_USBTLL_SYSSTATUS_RESETDONE_SHIFT 0
+#define OMAP_USBTLL_IRQSTATUS (OMAP_USBHOST_TLL_BASE + 0x18)
+#define OMAP_USBTLL_IRQENABLE (OMAP_USBHOST_TLL_BASE + 0x1C)
+
+#define OMAP_TLL_SHARED_CONF (OMAP_USBHOST_TLL_BASE + 0x30)
+ #define OMAP_TLL_SHARED_CONF_USB_90D_DDR_EN_SHFT 6
+ #define OMAP_TLL_SHARED_CONF_USB_180D_SDR_EN_SHIFT 5
+ #define OMAP_TLL_SHARED_CONF_USB_DIVRATION_SHIFT 2
+ #define OMAP_TLL_SHARED_CONF_FCLK_REQ_SHIFT 1
+ #define OMAP_TLL_SHARED_CONF_FCLK_IS_ON_SHIFT 0
+
+#define OMAP_TLL_CHANNEL_CONF(num)\
+ (OMAP_USBHOST_TLL_BASE + (0x040 + 0x004 * num))
+ #define OMAP_TLL_CHANNEL_CONF_ULPINOBITSTUFF_SHIFT 11
+ #define OMAP_TLL_CHANNEL_CONF_ULPI_ULPIAUTOIDLE_SHIFT 10
+ #define OMAP_TLL_CHANNEL_CONF_UTMIAUTOIDLE_SHIFT 9
+ #define OMAP_TLL_CHANNEL_CONF_ULPIDDRMODE_SHIFT 8
+ #define OMAP_TLL_CHANNEL_CONF_CHANEN_SHIFT 0
+
+#define OMAP_TLL_ULPI_FUNCTION_CTRL(num)\
+ (OMAP_USBHOST_TLL_BASE + (0x804 + 0x100 * num))
+#define OMAP_TLL_ULPI_INTERFACE_CTRL(num)\
+ (OMAP_USBHOST_TLL_BASE + (0x807 + 0x100 * num))
+#define OMAP_TLL_ULPI_OTG_CTRL(num)\
+ (OMAP_USBHOST_TLL_BASE + (0x80A + 0x100 * num))
+#define OMAP_TLL_ULPI_INT_EN_RISE(num)\
+ (OMAP_USBHOST_TLL_BASE + (0x80D + 0x100 * num))
+#define OMAP_TLL_ULPI_INT_EN_FALL(num)\
+ (OMAP_USBHOST_TLL_BASE + (0x810 + 0x100 * num))
+#define OMAP_TLL_ULPI_INT_STATUS(num)\
+ (OMAP_USBHOST_TLL_BASE + (0x813 + 0x100 * num))
+#define OMAP_TLL_ULPI_INT_LATCH(num)\
+ (OMAP_USBHOST_TLL_BASE + (0x814 + 0x100 * num))
+#define OMAP_TLL_ULPI_DEBUG(num)\
+ (OMAP_USBHOST_TLL_BASE + (0x815 + 0x100 * num))
+#define OMAP_TLL_ULPI_SCRATCH_REGISTER(num)\
+ (OMAP_USBHOST_TLL_BASE + (0x8165 + 0x100 * num))
+
+/* UHH Register Set */
+#define OMAP_USBHOST_UHH_BASE (OMAP_USBHOST_BASE + 0x4000)
+#define OMAP_UHH_REVISION (OMAP_USBHOST_UHH_BASE + 0x00)
+#define OMAP_UHH_SYSCONFIG (OMAP_USBHOST_UHH_BASE + 0x10)
+ #define OMAP_UHH_SYSCONFIG_MIDLEMODE_SHIFT 12
+ #define OMAP_UHH_SYSCONFIG_CACTIVITY_SHIFT 8
+ #define OMAP_UHH_SYSCONFIG_SIDLEMODE_SHIFT 3
+ #define OMAP_UHH_SYSCONFIG_ENAWAKEUP_SHIFT 2
+ #define OMAP_UHH_SYSCONFIG_SOFTRESET_SHIFT 1
+ #define OMAP_UHH_SYSCONFIG_AUTOIDLE_SHIFT 0
+
+#define OMAP_UHH_SYSSTATUS (OMAP_USBHOST_UHH_BASE + 0x14)
+#define OMAP_UHH_HOSTCONFIG (OMAP_USBHOST_UHH_BASE + 0x40)
+ #define OMAP_UHH_HOSTCONFIG_ULPI_BYPASS_SHIFT 0
+
+#define OMAP_UHH_DEBUG_CSR (OMAP_USBHOST_UHH_BASE + 0x44)
+
+/* EHCI Register Set */
+#define OMAP_USBHOST_EHCI_BASE (OMAP_USBHOST_BASE + 0x4800)
+#define EHCI_INSNREG05_ULPI (OMAP_USBHOST_EHCI_BASE + 0xA4)
+ #define EHCI_INSNREG05_ULPI_CONTROL_SHIFT 31
+ #define EHCI_INSNREG05_ULPI_PORTSEL_SHIFT 24
+ #define EHCI_INSNREG05_ULPI_OPSEL_SHIFT 22
+ #define EHCI_INSNREG05_ULPI_REGADD_SHIFT 16
+ #define EHCI_INSNREG05_ULPI_EXTREGADD_SHIFT 8
+ #define EHCI_INSNREG05_ULPI_WRDATA_SHIFT 0
+
+/* OHCI Register Set */
+#define OMAP_USBHOST_OHCI_BASE (OMAP_USBHOST_BASE + 0x4400)
+
+#endif/* __EHCI_OMAP_H*/
Index: omap-submit/drivers/usb/Kconfig
===================================================================
--- omap-submit.orig/drivers/usb/Kconfig 2008-02-04 17:06:27.000000000 +0530
+++ omap-submit/drivers/usb/Kconfig 2008-02-04 17:07:14.000000000 +0530
@@ -49,6 +49,7 @@
boolean
default y if PPC_83xx
default y if SOC_AU1200
+ default y if ARCH_OMAP34XX
default PCI
# ARM SA1111 chips have a non-PCI based "OHCI-compatible" USB host interface.
Index: omap-submit/drivers/usb/host/Kconfig
===================================================================
--- omap-submit.orig/drivers/usb/host/Kconfig 2008-02-04 17:06:27.000000000 +0530
+++ omap-submit/drivers/usb/host/Kconfig 2008-02-04 17:07:14.000000000 +0530
@@ -28,6 +28,25 @@
To compile this driver as a module, choose M here: the
module will be called ehci-hcd.
+choice
+ prompt "PHY/TLL mode"
+ depends on USB_EHCI_HCD && EXPERIMENTAL && ARCH_OMAP34XX
+ ---help---
+ Choose PHY or TLL mode of operation
+
+config OMAP_EHCI_PHY_MODE
+ bool "PHY mode: ISP1504 on Port1/2 (NEW 3430ES2.0)"
+ depends on USB_EHCI_HCD && EXPERIMENTAL && ARCH_OMAP34XX
+ ---help---
+ EHCI PHY mode. Port1 and Port2 are connected to ISP1504 transcievers
+
+config OMAP_EHCI_TLL_MODE
+ bool "TLL mode: (EXPERIMENTAL)"
+ depends on USB_EHCI_HCD && EXPERIMENTAL && ARCH_OMAP34XX
+ ---help---
+ OMAP EHCI controller has TLL mode of operation for all 3 ports.
+ Use this mode when no transciever is present
+endchoice
config USB_EHCI_SPLIT_ISO
bool "Full speed ISO transactions (EXPERIMENTAL)"
-
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
