Hello,
should I be worried by these messages? Both nfs & nfsd seems to
work, but on other side messages about nfsd4 being hung in D state for
more than 480 seconds look suspicious.
=============================================
[ INFO: possible recursive locking detected ]
2.6.28-64-06887-g85390a8-dirty #4
---------------------------------------------
nfsd4/4336 is trying to acquire lock:
(&type->i_mutex_dir_key#2){--..}, at: [<ffffffff8031ca24>]
vfs_fsync+0x84/0x100
but task is already holding lock:
(&type->i_mutex_dir_key#2){--..}, at: [<ffffffffa102a20d>]
nfsd4_sync_rec_dir+0x1d/0x50 [nfsd]
other info that might help us debug this:
4 locks held by nfsd4/4336:
#0: (nfsd4){--..}, at: [<ffffffff802628d3>] run_workqueue+0xb3/0x250
#1: ((laundromat_work).work){--..}, at: [<ffffffff802628d3>]
run_workqueue+0xb3/0x250
#2: (client_mutex){--..}, at: [<ffffffffa1024d6e>]
laundromat_main+0x2e/0x300 [nfsd]
#3: (&type->i_mutex_dir_key#2){--..}, at: [<ffffffffa102a20d>]
nfsd4_sync_rec_dir+0x1d/0x50 [nfsd]
...
INFO: lockdep is turned off.
INFO: task nfsd4:4336 blocked for more than 480 seconds.
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
Thanks,
Petr
Initializing cgroup subsys cpuset
Linux version 2.6.28-64-06887-g85390a8-dirty (root@petr-dev3) (gcc version 4.3.2 (Debian 4.3.2-1) ) #4 SMP PREEMPT Wed Jan 7 09:59:22 PST 2009
Command line: auto BOOT_IMAGE=Linux ro root=805 video=atyfb:1600x1200-16@60
KERNEL supported cpus:
Intel GenuineIntel
AMD AuthenticAMD
Centaur CentaurHauls
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e8000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 00000000cfff0000 (usable)
BIOS-e820: 00000000cfff0000 - 00000000cffff000 (ACPI data)
BIOS-e820: 00000000cffff000 - 00000000d0000000 (ACPI NVS)
BIOS-e820: 00000000ff780000 - 0000000100000000 (reserved)
BIOS-e820: 0000000100000000 - 0000000126000000 (usable)
DMI 2.3 present.
AMI BIOS detected: BIOS may corrupt low RAM, working it around.
last_pfn = 0x126000 max_arch_pfn = 0x100000000
x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
last_pfn = 0xcfff0 max_arch_pfn = 0x100000000
Scanning 0 areas for low memory corruption
modified physical RAM map:
modified: 0000000000000000 - 0000000000010000 (reserved)
modified: 0000000000010000 - 000000000009fc00 (usable)
modified: 000000000009fc00 - 00000000000a0000 (reserved)
modified: 00000000000e8000 - 0000000000100000 (reserved)
modified: 0000000000100000 - 00000000cfff0000 (usable)
modified: 00000000cfff0000 - 00000000cffff000 (ACPI data)
modified: 00000000cffff000 - 00000000d0000000 (ACPI NVS)
modified: 00000000ff780000 - 0000000100000000 (reserved)
modified: 0000000100000000 - 0000000126000000 (usable)
init_memory_mapping: 0000000000000000-00000000cfff0000
0000000000 - 00cfe00000 page 2M
00cfe00000 - 00cfff0000 page 4k
kernel direct mapping tables up to cfff0000 @ 10000-16000
last_map_addr: cfff0000 end: cfff0000
init_memory_mapping: 0000000100000000-0000000126000000
0100000000 - 0126000000 page 2M
kernel direct mapping tables up to 126000000 @ 14000-1a000
last_map_addr: 126000000 end: 126000000
ACPI: RSDP 000F9870, 0024 (r2 ACPIAM)
ACPI: XSDT CFFF0100, 0044 (r1 A M I OEMXSDT 5000622 MSFT 97)
ACPI: FACP CFFF0281, 00F4 (r3 A M I OEMFACP 5000622 MSFT 97)
ACPI: DSDT CFFF0460, 3470 (r1 H8DA8 H8DA8010 0 INTL 2002026)
ACPI: FACS CFFFF000, 0040
ACPI: APIC CFFF0380, 0084 (r1 A M I OEMAPIC 5000622 MSFT 97)
ACPI: OEMB CFFFF040, 0041 (r1 A M I OEMBIOS 5000622 MSFT 97)
ACPI: SRAT CFFF38D0, 0110 (r1 A M I OEMSRAT 5000622 MSFT 97)
ACPI: Local APIC address 0xfee00000
SRAT: PXM 0 -> APIC 0 -> Node 0
SRAT: PXM 0 -> APIC 1 -> Node 0
SRAT: PXM 1 -> APIC 2 -> Node 1
SRAT: PXM 1 -> APIC 3 -> Node 1
SRAT: Node 0 PXM 0 100000-80000000
SRAT: Node 1 PXM 1 80000000-d0000000
SRAT: Node 1 PXM 1 100000000-126000000
SRAT: Node 0 PXM 0 0-9fc00
NUMA: Allocated memnodemap from 15000 - 17500
NUMA: Using 20 for the hash shift.
Bootmem setup node 0 0000000000000000-0000000080000000
NODE_DATA [0000000000017500 - 000000000004b4ff]
bootmap [000000000004c000 - 000000000005bfff] pages 10
(7 early reservations) ==> bootmem [0000000000 - 0080000000]
#0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000]
#1 [0000006000 - 0000008000] TRAMPOLINE ==> [0000006000 - 0000008000]
#2 [0000200000 - 0001416b38] TEXT DATA BSS ==> [0000200000 - 0001416b38]
#3 [000009f800 - 0000100000] BIOS reserved ==> [000009f800 - 0000100000]
#4 [0000010000 - 0000014000] PGTABLE ==> [0000010000 - 0000014000]
#5 [0000014000 - 0000015000] PGTABLE ==> [0000014000 - 0000015000]
#6 [0000015000 - 0000017500] MEMNODEMAP ==> [0000015000 - 0000017500]
Bootmem setup node 1 0000000080000000-0000000126000000
NODE_DATA [0000000080000000 - 0000000080033fff]
bootmap [0000000080034000 - 0000000080048bff] pages 15
(7 early reservations) ==> bootmem [0080000000 - 0126000000]
#0 [0000000000 - 0000001000] BIOS data page
#1 [0000006000 - 0000008000] TRAMPOLINE
#2 [0000200000 - 0001416b38] TEXT DATA BSS
#3 [000009f800 - 0000100000] BIOS reserved
#4 [0000010000 - 0000014000] PGTABLE
#5 [0000014000 - 0000015000] PGTABLE
#6 [0000015000 - 0000017500] MEMNODEMAP
found SMP MP-table at [ffff8800000ff780] 000ff780
[ffffe20000000000-ffffe200033fffff] PMD -> [ffff880001600000-ffff8800049fffff] on node 0
[ffffe20003400000-ffffe200079fffff] PMD -> [ffff880080200000-ffff8800835fffff] on node 1
Zone PFN ranges:
DMA 0x00000010 -> 0x00001000
DMA32 0x00001000 -> 0x00100000
Normal 0x00100000 -> 0x00126000
Movable zone start PFN for each node
early_node_map[4] active PFN ranges
0: 0x00000010 -> 0x0000009f
0: 0x00000100 -> 0x00080000
1: 0x00080000 -> 0x000cfff0
1: 0x00100000 -> 0x00126000
On node 0 totalpages: 524175
DMA zone: 104 pages used for memmap
DMA zone: 108 pages reserved
DMA zone: 3771 pages, LIFO batch:0
DMA32 zone: 13208 pages used for memmap
DMA32 zone: 506984 pages, LIFO batch:31
On node 1 totalpages: 483312
DMA32 zone: 13312 pages used for memmap
DMA32 zone: 314352 pages, LIFO batch:31
Normal zone: 3952 pages used for memmap
Normal zone: 151696 pages, LIFO batch:31
ACPI: PM-Timer IO Port: 0x5008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
ACPI: LAPIC (acpi_id[0x03] lapic_id[0x02] enabled)
ACPI: LAPIC (acpi_id[0x04] lapic_id[0x03] enabled)
ACPI: IOAPIC (id[0x04] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 4, version 0, address 0xfec00000, GSI 0-23
ACPI: IOAPIC (id[0x05] address[0xfebfe000] gsi_base[24])
IOAPIC[1]: apic_id 5, version 0, address 0xfebfe000, GSI 24-27
ACPI: IOAPIC (id[0x06] address[0xfebff000] gsi_base[28])
IOAPIC[2]: apic_id 6, version 0, address 0xfebff000, GSI 28-31
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Using ACPI (MADT) for SMP configuration information
SMP: Allowing 4 CPUs, 0 hotplug CPUs
Allocating PCI resources starting at d4000000 (gap: d0000000:2f780000)
NR_CPUS:4096 nr_cpumask_bits:4 nr_cpu_ids:4 nr_node_ids:2
PERCPU: Allocating 1892352 bytes of per cpu data
Built 2 zonelists in Node order, mobility grouping on. Total pages: 976803
Policy zone: Normal
Kernel command line: auto BOOT_IMAGE=Linux ro root=805 video=atyfb:1600x1200-16@60
Initializing CPU#0
Preemptible RCU implementation.
PID hash table entries: 4096 (order: 12, 32768 bytes)
Extended CMOS year: 2000
Fast TSC calibration using PIT
Detected 1994.552 MHz processor.
Console: colour VGA+ 80x25
console [tty0] enabled
Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar
... MAX_LOCKDEP_SUBCLASSES: 8
... MAX_LOCK_DEPTH: 48
... MAX_LOCKDEP_KEYS: 8191
... CLASSHASH_SIZE: 4096
... MAX_LOCKDEP_ENTRIES: 8192
... MAX_LOCKDEP_CHAINS: 16384
... CHAINHASH_SIZE: 8192
memory used by lock dependency info: 4351 kB
per task-struct memory footprint: 2688 bytes
allocated 40632320 bytes of page_cgroup
please try cgroup_disable=memory option if you don't want
Checking aperture...
No AGP bridge found
Node 0: aperture @ da000000 size 32 MB
Aperture too small (32 MB) than (64 MB)
Your BIOS doesn't leave a aperture memory hole
Please enable the IOMMU option in the BIOS setup
This costs you 64 MB of RAM
Mapping aperture over 65536 KB of RAM @ 20000000
Memory: 3790436k/4816896k available (3843k kernel code, 786948k absent, 239512k reserved, 2813k data, 2428k init)
SLUB: Genslabs=13, HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=2
Calibrating delay loop (skipped), value calculated using timer frequency.. 3989.10 BogoMIPS (lpj=19945520)
Security Framework initialized
SELinux: Disabled at boot.
Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
Mount-cache hash table entries: 256
Initializing cgroup subsys debug
Initializing cgroup subsys ns
Initializing cgroup subsys cpuacct
Initializing cgroup subsys memory
Initializing cgroup subsys devices
Initializing cgroup subsys freezer
Initializing cgroup subsys net_cls
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 1024K (64 bytes/line)
CPU 0/0x0 -> Node 0
tseg: 0000000000
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
ACPI: Core revision 20080926
Setting APIC routing to flat
alloc irq_2_pin on cpu 0 node 0
alloc irq_2_pin on cpu 0 node 0
alloc irq_2_pin on cpu 0 node 0
alloc irq_2_pin on cpu 0 node 0
alloc irq_2_pin on cpu 0 node 0
alloc irq_2_pin on cpu 0 node 0
alloc irq_2_pin on cpu 0 node 0
alloc irq_2_pin on cpu 0 node 0
alloc irq_2_pin on cpu 0 node 0
alloc irq_2_pin on cpu 0 node 0
alloc irq_2_pin on cpu 0 node 0
alloc irq_2_pin on cpu 0 node 0
alloc irq_2_pin on cpu 0 node 0
alloc irq_2_pin on cpu 0 node 0
alloc irq_2_pin on cpu 0 node 0
..TIMER: vector=0x30 apic1=0 pin1=2 apic2=0 pin2=0
CPU0: Dual Core AMD Opteron(tm) Processor 270 stepping 02
lockdep: fixing up alternatives.
Booting processor 1 APIC 0x1 ip 0x6000
Initializing CPU#1
Calibrating delay using timer specific routine.. 3988.73 BogoMIPS (lpj=19943673)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 1024K (64 bytes/line)
CPU 1/0x1 -> Node 0
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
x86 PAT enabled: cpu 1, old 0x7040600070406, new 0x7010600070106
CPU1: Dual Core AMD Opteron(tm) Processor 270 stepping 02
lockdep: fixing up alternatives.
Booting processor 2 APIC 0x2 ip 0x6000
Initializing CPU#2
Calibrating delay using timer specific routine.. 3988.74 BogoMIPS (lpj=19943723)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 1024K (64 bytes/line)
CPU 2/0x2 -> Node 1
CPU: Physical Processor ID: 1
CPU: Processor Core ID: 0
x86 PAT enabled: cpu 2, old 0x7040600070406, new 0x7010600070106
CPU2: Dual Core AMD Opteron(tm) Processor 270 stepping 02
lockdep: fixing up alternatives.
Booting processor 3 APIC 0x3 ip 0x6000
Initializing CPU#3
Calibrating delay using timer specific routine.. 3988.74 BogoMIPS (lpj=19943735)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 1024K (64 bytes/line)
CPU 3/0x3 -> Node 1
CPU: Physical Processor ID: 1
CPU: Processor Core ID: 1
x86 PAT enabled: cpu 3, old 0x7040600070406, new 0x7010600070106
CPU3: Dual Core AMD Opteron(tm) Processor 270 stepping 02
Brought up 4 CPUs
Total of 4 processors activated (15955.33 BogoMIPS).
CPU0 attaching sched-domain:
domain 0: span 0-1 level CPU
groups: 0 1
domain 1: span 0-3 level NODE
groups: 0-1 2-3
CPU1 attaching sched-domain:
domain 0: span 0-1 level CPU
groups: 1 0
domain 1: span 0-3 level NODE
groups: 0-1 2-3
CPU2 attaching sched-domain:
domain 0: span 2-3 level CPU
groups: 2 3
domain 1: span 0-3 level NODE
groups: 2-3 0-1
CPU3 attaching sched-domain:
domain 0: span 2-3 level CPU
groups: 3 2
domain 1: span 0-3 level NODE
groups: 2-3 0-1
net_namespace: 2160 bytes
NET: Registered protocol family 16
node 0 link 2: io port [1000, ffffff]
TOM: 00000000d0000000 aka 3328M
node 0 link 2: mmio [a0000, bffff]
node 0 link 2: mmio [d0000000, ffffffff]
TOM2: 0000000126000000 aka 4704M
bus: [00,ff] on node 0 link 2
bus: 00 index 0 io port: [0, ffff]
bus: 00 index 1 mmio: [a0000, bffff]
bus: 00 index 2 mmio: [d0000000, ffffffff]
bus: 00 index 3 mmio: [126000000, fcffffffff]
ACPI: bus type pci registered
PCI: Using configuration type 1 for base access
bio: create slab <bio-0> at 0
ACPI: EC: Look up EC in DSDT
ACPI: Interpreter enabled
ACPI: (supports S0 S1 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: No dock devices found.
ACPI: PCI Root Bridge [PCI0] (0000:00)
pci 0000:00:07.1: reg 20 io port: [0xffa0-0xffaf]
pci 0000:00:07.2: reg 10 io port: [0xcc00-0xcc1f]
pci 0000:00:0a.1: reg 10 64bit mmio: [0xfebfe000-0xfebfefff]
pci 0000:00:0b.1: reg 10 64bit mmio: [0xfebff000-0xfebfffff]
pci 0000:03:00.0: reg 10 32bit mmio: [0xfeafe000-0xfeafefff]
pci 0000:03:00.1: reg 10 32bit mmio: [0xfeafd000-0xfeafdfff]
pci 0000:00:06.0: bridge 32bit mmio: [0xfea00000-0xfeafffff]
pci 0000:02:01.0: reg 10 64bit mmio: [0xfe8fbc00-0xfe8fbc7f]
pci 0000:02:01.0: reg 18 64bit mmio: [0xfe8f0000-0xfe8f7fff]
pci 0000:02:01.0: reg 20 io port: [0xbc00-0xbc0f]
pci 0000:02:01.0: reg 30 32bit mmio: [0xfe700000-0xfe77ffff]
pci 0000:02:01.0: supports D1 D2
pci 0000:02:03.0: reg 10 io port: [0xb800-0xb8ff]
pci 0000:02:03.0: reg 14 64bit mmio: [0xfe8fe000-0xfe8fffff]
pci 0000:02:03.0: reg 1c io port: [0xb400-0xb4ff]
pci 0000:02:03.0: reg 30 32bit mmio: [0xfe800000-0xfe87ffff]
pci 0000:02:03.1: reg 10 io port: [0xb000-0xb0ff]
pci 0000:02:03.1: reg 14 64bit mmio: [0xfe8fc000-0xfe8fdfff]
pci 0000:02:03.1: reg 1c io port: [0xa800-0xa8ff]
pci 0000:02:03.1: reg 30 32bit mmio: [0xfe780000-0xfe7fffff]
pci 0000:02:05.0: reg 10 64bit mmio: [0xfe8e0000-0xfe8effff]
pci 0000:02:05.0: PME# supported from D3hot D3cold
pci 0000:02:05.0: PME# disabled
pci 0000:02:05.1: reg 10 64bit mmio: [0xfe8d0000-0xfe8dffff]
pci 0000:02:05.1: PME# supported from D3hot D3cold
pci 0000:02:05.1: PME# disabled
pci 0000:00:0a.0: bridge io port: [0xa000-0xbfff]
pci 0000:00:0a.0: bridge 32bit mmio: [0xfe600000-0xfe9fffff]
pci 0000:00:0a.0: bridge 64bit mmio pref: [0xfc300000-0xfc3fffff]
pci 0000:01:01.0: reg 10 32bit mmio: [0xfd000000-0xfdffffff]
pci 0000:01:01.0: reg 14 32bit mmio: [0xe0000000-0xefffffff]
pci 0000:01:01.0: reg 30 32bit mmio: [0xfe5e0000-0xfe5fffff]
pci 0000:00:0b.0: bridge 32bit mmio: [0xfc500000-0xfe5fffff]
pci 0000:00:0b.0: bridge 64bit mmio pref: [0xdc300000-0xfc2fffff]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.GOLA._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.GOLB._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
ACPI: WMI: Mapper loaded
SCSI subsystem initialized
libata version 3.00 loaded.
PCI: Using ACPI for IRQ routing
NetLabel: Initializing
NetLabel: domain hash size = 128
NetLabel: protocols = UNLABELED CIPSOv4
NetLabel: unlabeled traffic allowed by default
PCI-DMA: Disabling AGP.
PCI-DMA: aperture base @ 20000000 size 65536 KB
PCI-DMA: using GART IOMMU.
PCI-DMA: Reserving 64MB of IOMMU area in the AGP aperture
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 16 devices
ACPI: ACPI bus type pnp unregistered
system 00:0b: ioport range 0x680-0x6ff has been reserved
system 00:0b: ioport range 0x295-0x296 has been reserved
system 00:0b: ioport range 0xb78-0xb7f has been reserved
system 00:0b: ioport range 0xf78-0xf7f has been reserved
system 00:0c: ioport range 0x4d0-0x4d1 has been reserved
system 00:0c: ioport range 0x5000-0x50bf has been reserved
system 00:0c: ioport range 0x50e0-0x50ff has been reserved
system 00:0c: ioport range 0x50c0-0x50df has been reserved
system 00:0c: ioport range 0xde00-0xde7f has been reserved
system 00:0c: ioport range 0xde80-0xdeff has been reserved
system 00:0e: ioport range 0xca2-0xca3 has been reserved
system 00:0e: iomem range 0xfec00000-0xfec00fff has been reserved
system 00:0e: iomem range 0xfee00000-0xfee00fff has been reserved
system 00:0e: iomem range 0xfff80000-0xffffffff has been reserved
system 00:0e: iomem range 0xff780000-0xff7fffff has been reserved
system 00:0f: iomem range 0x0-0x9ffff could not be reserved
system 00:0f: iomem range 0xc0000-0xdffff has been reserved
system 00:0f: iomem range 0xe0000-0xfffff could not be reserved
system 00:0f: iomem range 0x100000-0xcfffffff could not be reserved
pci 0000:00:06.0: PCI bridge, secondary bus 0000:03
pci 0000:00:06.0: IO window: disabled
pci 0000:00:06.0: MEM window: 0xfea00000-0xfeafffff
pci 0000:00:06.0: PREFETCH window: disabled
pci 0000:00:0a.0: PCI bridge, secondary bus 0000:02
pci 0000:00:0a.0: IO window: 0xa000-0xbfff
pci 0000:00:0a.0: MEM window: 0xfe600000-0xfe9fffff
pci 0000:00:0a.0: PREFETCH window: 0x000000fc300000-0x000000fc3fffff
pci 0000:00:0b.0: PCI bridge, secondary bus 0000:01
pci 0000:00:0b.0: IO window: disabled
pci 0000:00:0b.0: MEM window: 0xfc500000-0xfe5fffff
pci 0000:00:0b.0: PREFETCH window: 0x000000dc300000-0x000000fc2fffff
bus: 00 index 0 io port: [0x00-0xffff]
bus: 00 index 1 mmio: [0x000000-0xffffffffffffffff]
bus: 03 index 0 mmio: [0x0-0x0]
bus: 03 index 1 mmio: [0xfea00000-0xfeafffff]
bus: 03 index 2 mmio: [0x0-0x0]
bus: 03 index 3 mmio: [0x0-0x0]
bus: 02 index 0 io port: [0xa000-0xbfff]
bus: 02 index 1 mmio: [0xfe600000-0xfe9fffff]
bus: 02 index 2 mmio: [0xfc300000-0xfc3fffff]
bus: 02 index 3 mmio: [0x0-0x0]
bus: 01 index 0 mmio: [0x0-0x0]
bus: 01 index 1 mmio: [0xfc500000-0xfe5fffff]
bus: 01 index 2 mmio: [0xdc300000-0xfc2fffff]
bus: 01 index 3 mmio: [0x0-0x0]
NET: Registered protocol family 2
Switched to high resolution mode on CPU 0
Switched to high resolution mode on CPU 1
Switched to high resolution mode on CPU 3
Switched to high resolution mode on CPU 2
IP route cache hash table entries: 131072 (order: 8, 1048576 bytes)
TCP established hash table entries: 524288 (order: 11, 8388608 bytes)
TCP bind hash table entries: 65536 (order: 10, 4718592 bytes)
TCP: Hash tables configured (established 524288 bind 65536)
TCP reno registered
NET: Registered protocol family 1
microcode: CPU0: AMD CPU family 0xf not supported
microcode: CPU1: AMD CPU family 0xf not supported
microcode: CPU2: AMD CPU family 0xf not supported
microcode: CPU3: AMD CPU family 0xf not supported
Microcode Update Driver: v2.00 <tigran@xxxxxxxxxxxxxxxxxxxx>, Peter Oruba
Scanning for low memory corruption every 60 seconds
Initializing RT-Tester: OK
audit: initializing netlink socket (disabled)
type=2000 audit(1231352315.220:1): initialized
HugeTLB registered 2 MB page size, pre-allocated 0 pages
Created ptmx node in devpts ino 2
msgmni has been set to 7403
alg: No test for stdrng (krng)
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
boot interrupts on PCI device 0x1022:0x746b already disabled
pci 0000:00:0a.0: MSI quirk detected; subordinate MSI disabled
disabled boot interrupts on PCI device 0x1022:0x7450
pci 0000:00:0b.0: MSI quirk detected; subordinate MSI disabled
disabled boot interrupts on PCI device 0x1022:0x7450
pci 0000:01:01.0: nv_msi_ht_cap_quirk didn't locate host bridge
pci 0000:01:01.0: Boot video device
vendor=1022 device=7450
alloc irq_desc for 28 on cpu 0 node 0
alloc kstat_irqs on cpu 0 node 0
alloc irq_cfg on cpu 0 node 0
alloc irq_2_pin on cpu 0 node 0
nvidiafb 0000:01:01.0: PCI INT A -> GSI 28 (level, low) -> IRQ 28
nvidiafb: Device ID: 10de0322
nvidiafb: CRTC0 analog found
nvidiafb: CRTC1 analog found
nvidiafb: EDID found from BUS1
i2c-adapter i2c-1: unable to read EDID block.
i2c-adapter i2c-1: unable to read EDID block.
i2c-adapter i2c-1: unable to read EDID block.
nvidiafb: CRTC 0 appears to have a CRT attached
nvidiafb: Using CRT on CRTC 0
mtrr: type mismatch for e0000000,10000000 old: write-back new: write-combining
nvidiafb: unable to setup MTRR
Console: switching to colour frame buffer device 200x75
nvidiafb: PCI nVidia NV32 framebuffer (64MB @ 0xE0000000)
input: Power Button (FF) as /class/input/input0
ACPI: Power Button (FF) [PWRF]
input: Power Button (CM) as /class/input/input1
ACPI: Power Button (CM) [PWRB]
processor ACPI_CPU:00: registered as cooling_device0
ACPI: Processor [CPU1] (supports 8 throttling states)
processor ACPI_CPU:01: registered as cooling_device1
processor ACPI_CPU:02: registered as cooling_device2
processor ACPI_CPU:03: registered as cooling_device3
Real Time Clock Driver v1.12ac
hpet_acpi_add: no address or irqs in _CRS
Non-volatile memory driver v1.3
Linux agpgart interface v0.103
[drm] Initialized drm 1.1.0 20060810
console [netcon0] enabled
netconsole: network logging started
Driver 'sd' needs updating - please use bus_type methods
pata_amd 0000:00:07.1: version 0.3.10
scsi0 : pata_amd
scsi1 : pata_amd
ata1: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xffa0 irq 14
ata2: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0xffa8 irq 15
ata1.00: ATA-7: ST3120814A, 3.AAJ, max UDMA/100
ata1.00: 234441648 sectors, multi 16: LBA48
ata1.01: ATA-7: ST3500630A, 3.AAC, max UDMA/100
ata1.01: 976773168 sectors, multi 16: LBA48
ata1.00: configured for UDMA/100
ata1.01: configured for UDMA/100
ata2.00: ATAPI: SONY DVD RW DW-Q120A, PYS2, max UDMA/66
ata2.00: configured for UDMA/66
scsi 0:0:0:0: Direct-Access ATA ST3120814A 3.AA PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] 234441648 512-byte hardware sectors: (120 GB/111 GiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:0:0: [sda] 234441648 512-byte hardware sectors: (120 GB/111 GiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda: sda1 sda2 sda3 sda4 < sda5 >
sd 0:0:0:0: [sda] Attached SCSI disk
scsi 0:0:1:0: Direct-Access ATA ST3500630A 3.AA PQ: 0 ANSI: 5
sd 0:0:1:0: [sdb] 976773168 512-byte hardware sectors: (500 GB/465 GiB)
sd 0:0:1:0: [sdb] Write Protect is off
sd 0:0:1:0: [sdb] Mode Sense: 00 3a 00 00
sd 0:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:1:0: [sdb] 976773168 512-byte hardware sectors: (500 GB/465 GiB)
sd 0:0:1:0: [sdb] Write Protect is off
sd 0:0:1:0: [sdb] Mode Sense: 00 3a 00 00
sd 0:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdb: sdb2
sd 0:0:1:0: [sdb] Attached SCSI disk
scsi 1:0:0:0: CD-ROM SONY DVD RW DW-Q120A PYS2 PQ: 0 ANSI: 5
Fusion MPT base driver 3.04.07
Copyright (c) 1999-2008 LSI Corporation
Fusion MPT SPI Host driver 3.04.07
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
input: PC Speaker as /class/input/input2
input: AT Translated Set 2 keyboard as /class/input/input3
cpuidle: using governor ladder
oprofile: using NMI interrupt.
TCP cubic registered
powernow-k8: Found 2 Dual Core AMD Opteron(tm) Processor 270 processors (4 cpu cores) (version 2.20.00)
powernow-k8: 0 : fid 0xc (2000 MHz), vid 0x8
powernow-k8: 1 : fid 0xa (1800 MHz), vid 0xa
powernow-k8: 2 : fid 0x2 (1000 MHz), vid 0x12
powernow-k8: 0 : fid 0xc (2000 MHz), vid 0x8
powernow-k8: 1 : fid 0xa (1800 MHz), vid 0xa
powernow-k8: 2 : fid 0x2 (1000 MHz), vid 0x12
registered taskstats version 1
BIOS EDD facility v0.16 2004-Jun-25, 3 devices found
input: ImExPS/2 Generic Explorer Mouse as /class/input/input4
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly on device 8:5.
Freeing unused kernel memory: 2428k freed
Write protecting the kernel read-only data: 5600k
kjournald starting. Commit interval 5 seconds
input: ImExPS/2 Generic Explorer Mouse as /class/input/input5
Driver 'sr' needs updating - please use bus_type methods
sr0: scsi3-mmc drive: 48x/48x writer cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sr 1:0:0:0: Attached scsi CD-ROM sr0
sd 0:0:0:0: Attached scsi generic sg0 type 0
sd 0:0:1:0: Attached scsi generic sg1 type 0
sr 1:0:0:0: Attached scsi generic sg2 type 5
parport_pc 00:0a: reported by Plug and Play ACPI
parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP,TRISTATE,EPP]
Serial: 8250/16550 driver4 ports, IRQ sharing disabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
00:07: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:08: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp 0000:00:06.0: HPC vendor_id 1022 device_id 7460 ss_vid 0 ss_did 0
shpchp 0000:00:06.0: Cannot reserve MMIO region
shpchp 0000:00:0a.0: HPC vendor_id 1022 device_id 7450 ss_vid 0 ss_did 0
shpchp 0000:00:0a.0: Cannot reserve MMIO region
shpchp 0000:00:0b.0: HPC vendor_id 1022 device_id 7450 ss_vid 0 ss_did 0
shpchp 0000:00:0b.0: Cannot reserve MMIO region
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
ACPI: I/O resource amd756_smbus [0x50e0-0x50ef] conflicts with ACPI region PMIO [0x5000-0x50fe]
ACPI: Device needs an ACPI driver
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
vendor=1022 device=7460
alloc irq_desc for 19 on cpu 0 node 0
alloc kstat_irqs on cpu 0 node 0
alloc irq_cfg on cpu 0 node 0
alloc irq_2_pin on cpu 0 node 0
ohci_hcd 0000:03:00.0: PCI INT D -> GSI 19 (level, low) -> IRQ 19
ohci_hcd 0000:03:00.0: OHCI Host Controller
ohci_hcd 0000:03:00.0: new USB bus registered, assigned bus number 1
ohci_hcd 0000:03:00.0: irq 19, io mem 0xfeafe000
tg3.c:v3.97 (December 10, 2008)
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 3 ports detected
usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: OHCI Host Controller
vendor=1022 device=7450
alloc irq_desc for 26 on cpu 0 node 0
alloc kstat_irqs on cpu 0 node 0
alloc irq_cfg on cpu 0 node 0
alloc irq_2_pin on cpu 0 node 0
tg3 0000:02:05.0: PCI INT A -> GSI 26 (level, low) -> IRQ 26
usb usb1: Manufacturer: Linux 2.6.28-64-06887-g85390a8-dirty ohci_hcd
usb usb1: SerialNumber: 0000:03:00.0
vendor=1022 device=7460
ohci_hcd 0000:03:00.1: PCI INT D -> GSI 19 (level, low) -> IRQ 19
ohci_hcd 0000:03:00.1: OHCI Host Controller
ohci_hcd 0000:03:00.1: new USB bus registered, assigned bus number 2
tg3 0000:02:05.0: PME# disabled
ohci_hcd 0000:03:00.1: irq 19, io mem 0xfeafd000
eth0: Tigon3 [partno(BCM95704A6) rev 2100] (PCIX:66MHz:64-bit) MAC address 00:30:48:59:8f:be
eth0: attached PHY is 5704 (10/100/1000Base-T Ethernet) (WireSpeed[1])
eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[1] TSOcap[0]
eth0: dma_rwctrl[769f0000] dma_mask[64-bit]
sata_sil24 0000:02:01.0: version 1.1
vendor=1022 device=7450
alloc irq_desc for 24 on cpu 0 node 0
alloc kstat_irqs on cpu 0 node 0
alloc irq_cfg on cpu 0 node 0
alloc irq_2_pin on cpu 0 node 0
sata_sil24 0000:02:01.0: PCI INT A -> GSI 24 (level, low) -> IRQ 24
sata_sil24 0000:02:01.0: Applying completion IRQ loss on PCI-X errata fix
scsi2 : sata_sil24
scsi3 : sata_sil24
scsi4 : sata_sil24
scsi5 : sata_sil24
ata3: SATA max UDMA/100 host m128@0xfe8fbc00 port 0xfe8f0000 irq 24
ata4: SATA max UDMA/100 host m128@0xfe8fbc00 port 0xfe8f2000 irq 24
ata5: SATA max UDMA/100 host m128@0xfe8fbc00 port 0xfe8f4000 irq 24
ata6: SATA max UDMA/100 host m128@0xfe8fbc00 port 0xfe8f6000 irq 24
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 3 ports detected
usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: OHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.28-64-06887-g85390a8-dirty ohci_hcd
usb usb2: SerialNumber: 0000:03:00.1
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 0)
ata3.00: ATA-6: Sans Digital V.36.A0B, V.36.A0B, max UDMA/133
ata3.00: 5860554240 sectors, multi 1: LBA48
ata3.00: applying bridge limits
ata3.00: configured for UDMA/100
ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 0)
ata4.15: Port Multiplier 1.1, 0x1095:0x3726 r23, 6 ports, feat 0x1/0x9
ata4.00: hard resetting link
ata4.00: SATA link up 3.0 Gbps (SStatus 123 SControl 320)
ata4.01: hard resetting link
ata4.01: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata4.02: hard resetting link
ata4.02: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata4.03: hard resetting link
ata4.03: SATA link down (SStatus 0 SControl 320)
ata4.04: hard resetting link
ata4.04: SATA link down (SStatus 0 SControl 320)
ata4.05: hard resetting link
ata4.05: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
ata4.00: ATA-7: ST3750640AS, 3.AAE, max UDMA/133
ata4.00: 1465149168 sectors, multi 0: LBA48 NCQ (depth 31/32)
ata4.00: configured for UDMA/100
ata4.01: ATA-7: Hitachi HDS721010KLA330, GKAOA70F, max UDMA/133
ata4.01: 1953525168 sectors, multi 0: LBA48 NCQ (depth 31/32)
ata4.01: configured for UDMA/100
ata4.02: ATA-7: Hitachi HDS721010KLA330, GKAOA70F, max UDMA/133
ata4.02: 1953525168 sectors, multi 0: LBA48 NCQ (depth 31/32)
ata4.02: configured for UDMA/100
ata4: EH complete
ata5: SATA link down (SStatus 0 SControl 0)
ata6: SATA link down (SStatus 0 SControl 0)
scsi 2:0:0:0: Direct-Access ATA Sans Digital V.3 V.36 PQ: 0 ANSI: 5
sd 2:0:0:0: [sdc] Very big device. Trying to use READ CAPACITY(16).
sd 2:0:0:0: [sdc] 5860554240 512-byte hardware sectors: (3.00 TB/2.72 TiB)
sd 2:0:0:0: [sdc] Write Protect is off
sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sdc] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
sd 2:0:0:0: [sdc] Very big device. Trying to use READ CAPACITY(16).
sd 2:0:0:0: [sdc] 5860554240 512-byte hardware sectors: (3.00 TB/2.72 TiB)
sd 2:0:0:0: [sdc] Write Protect is off
sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sdc] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
sdc: sdc1 sdc2
sd 2:0:0:0: [sdc] Attached SCSI disk
sd 2:0:0:0: Attached scsi generic sg3 type 0
scsi 3:0:0:0: Direct-Access ATA ST3750640AS 3.AA PQ: 0 ANSI: 5
sd 3:0:0:0: [sdd] 1465149168 512-byte hardware sectors: (750 GB/698 GiB)
sd 3:0:0:0: [sdd] Write Protect is off
sd 3:0:0:0: [sdd] Mode Sense: 00 3a 00 00
sd 3:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 3:0:0:0: [sdd] 1465149168 512-byte hardware sectors: (750 GB/698 GiB)
sd 3:0:0:0: [sdd] Write Protect is off
sd 3:0:0:0: [sdd] Mode Sense: 00 3a 00 00
sd 3:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdd: sdd1
sd 3:0:0:0: [sdd] Attached SCSI disk
sd 3:0:0:0: Attached scsi generic sg4 type 0
scsi 3:1:0:0: Direct-Access ATA Hitachi HDS72101 GKAO PQ: 0 ANSI: 5
sd 3:1:0:0: [sde] 1953525168 512-byte hardware sectors: (1.00 TB/931 GiB)
sd 3:1:0:0: [sde] Write Protect is off
sd 3:1:0:0: [sde] Mode Sense: 00 3a 00 00
sd 3:1:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 3:1:0:0: [sde] 1953525168 512-byte hardware sectors: (1.00 TB/931 GiB)
sd 3:1:0:0: [sde] Write Protect is off
sd 3:1:0:0: [sde] Mode Sense: 00 3a 00 00
sd 3:1:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sde: sde1
sd 3:1:0:0: [sde] Attached SCSI disk
sd 3:1:0:0: Attached scsi generic sg5 type 0
scsi 3:2:0:0: Direct-Access ATA Hitachi HDS72101 GKAO PQ: 0 ANSI: 5
sd 3:2:0:0: [sdf] 1953525168 512-byte hardware sectors: (1.00 TB/931 GiB)
sd 3:2:0:0: [sdf] Write Protect is off
sd 3:2:0:0: [sdf] Mode Sense: 00 3a 00 00
sd 3:2:0:0: [sdf] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 3:2:0:0: [sdf] 1953525168 512-byte hardware sectors: (1.00 TB/931 GiB)
sd 3:2:0:0: [sdf] Write Protect is off
sd 3:2:0:0: [sdf] Mode Sense: 00 3a 00 00
sd 3:2:0:0: [sdf] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdf: sdf1
sd 3:2:0:0: [sdf] Attached SCSI disk
sd 3:2:0:0: Attached scsi generic sg6 type 0
vendor=1022 device=7450
alloc irq_desc for 27 on cpu 0 node 0
alloc kstat_irqs on cpu 0 node 0
alloc irq_cfg on cpu 0 node 0
alloc irq_2_pin on cpu 0 node 0
tg3 0000:02:05.1: PCI INT B -> GSI 27 (level, low) -> IRQ 27
tg3 0000:02:05.1: PME# disabled
tg3 0000:02:05.1: firmware: requesting tigon/tg3_tso.bin
eth1: Tigon3 [partno(BCM95704A6) rev 2100] (PCIX:66MHz:64-bit) MAC address 00:30:48:59:8f:bf
eth1: attached PHY is 5704 (10/100/1000Base-T Ethernet) (WireSpeed[1])
eth1: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] TSOcap[1]
eth1: dma_rwctrl[769f0000] dma_mask[64-bit]
vendor=1022 device=7450
aic79xx 0000:02:03.0: PCI INT A -> GSI 24 (level, low) -> IRQ 24
scsi6 : Adaptec AIC79XX PCI-X SCSI HBA DRIVER, Rev 3.0
<Adaptec AIC7902 Ultra320 SCSI adapter>
aic7902: Ultra320 Wide Channel A, SCSI Id=7, PCI-X 50-66MHz, 512 SCBs
vendor=1022 device=7450
alloc irq_desc for 25 on cpu 0 node 0
alloc kstat_irqs on cpu 0 node 0
alloc irq_cfg on cpu 0 node 0
alloc irq_2_pin on cpu 0 node 0
aic79xx 0000:02:03.1: PCI INT B -> GSI 25 (level, low) -> IRQ 25
scsi 6:0:0:0: Direct-Access SEAGATE ST3146707LW 0005 PQ: 0 ANSI: 3
target6:0:0: asynchronous
scsi6:A:0:0: Tagged Queuing enabled. Depth 32
target6:0:0: Beginning Domain Validation
target6:0:0: wide asynchronous
target6:0:0: FAST-160 WIDE SCSI 320.0 MB/s DT IU QAS RDSTRM RTI WRFLOW PCOMP (6.25 ns, offset 63)
target6:0:0: Ending Domain Validation
sd 6:0:0:0: [sdg] 286749488 512-byte hardware sectors: (146 GB/136 GiB)
sd 6:0:0:0: [sdg] Write Protect is off
sd 6:0:0:0: [sdg] Mode Sense: ab 00 10 08
sd 6:0:0:0: [sdg] Write cache: enabled, read cache: enabled, supports DPO and FUA
sd 6:0:0:0: [sdg] 286749488 512-byte hardware sectors: (146 GB/136 GiB)
sd 6:0:0:0: [sdg] Write Protect is off
sd 6:0:0:0: [sdg] Mode Sense: ab 00 10 08
sd 6:0:0:0: [sdg] Write cache: enabled, read cache: enabled, supports DPO and FUA
sdg: sdg1
sd 6:0:0:0: [sdg] Attached SCSI disk
sd 6:0:0:0: Attached scsi generic sg7 type 0
scsi7 : Adaptec AIC79XX PCI-X SCSI HBA DRIVER, Rev 3.0
<Adaptec AIC7902 Ultra320 SCSI adapter>
aic7902: Ultra320 Wide Channel B, SCSI Id=7, PCI-X 50-66MHz, 512 SCBs
Adding 2040244k swap on /dev/sda2. Priority:-1 extents:1 across:2040244k
EXT3 FS on sda5, internal journal
i2c-adapter i2c-3: Unrecognized stepping 0x45. Defaulting to ADM1026.
Shortest wait: 0
Longest wait: 12
w83627hf: Found W83627HF chip at 0x290
WDT driver for the Winbond(TM) W83627HF/THF/HG Super I/O chip initialising.
w83627hf/thf/hg WDT: initialized. timeout=60 sec (nowayout=0)
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
fuse init (API version 7.11)
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on sdb2, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on sde1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on sdf1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
NET: Registered protocol family 15
alg: No test for cipher_null (cipher_null-generic)
alg: No test for digest_null (digest_null-generic)
alg: No test for compress_null (compress_null-generic)
tg3 0000:02:05.0: PME# disabled
ADDRCONF(NETDEV_UP): eth0: link is not ready
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
tg3: eth0: Link is up at 1000 Mbps, full duplex.
tg3: eth0: Flow control is on for TX and on for RX.
ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
Installing knfsd (copyright (C) 1996 okir@xxxxxxxxxxxx).
BUG: using smp_processor_id() in preemptible [00000000] code: cpufreq-set/4048
caller is powernowk8_target+0xc5/0x7a0
Pid: 4048, comm: cpufreq-set Not tainted 2.6.28-64-06887-g85390a8-dirty #4
Call Trace:
[<ffffffff803e8d3e>] debug_smp_processor_id+0xee/0xf0
[<ffffffff8021e7f5>] powernowk8_target+0xc5/0x7a0
[<ffffffff80278db0>] ? check_noncircular+0xa0/0x180
[<ffffffff804f2b7c>] __cpufreq_driver_target+0x3c/0x40
[<ffffffff804f5878>] cpufreq_governor_performance+0x28/0x30
[<ffffffff804f2cf1>] __cpufreq_governor+0xd1/0x150
[<ffffffff804f3090>] __cpufreq_set_policy+0x170/0x1a0
[<ffffffff804f3dd9>] store_scaling_governor+0xc9/0x270
[<ffffffff804f4db0>] ? handle_update+0x0/0x10
[<ffffffff805b81c2>] ? _spin_unlock_irqrestore+0x42/0x80
[<ffffffff804f4c60>] store+0x70/0xb0
[<ffffffff803544da>] sysfs_write_file+0xca/0x140
[<ffffffff802f9beb>] vfs_write+0xcb/0x190
[<ffffffff802f9da0>] sys_write+0x50/0x90
[<ffffffff8020c5db>] system_call_fastpath+0x16/0x1b
BUG: using smp_processor_id() in preemptible [00000000] code: cpufreq-set/4049
caller is powernowk8_target+0xc5/0x7a0
Pid: 4049, comm: cpufreq-set Not tainted 2.6.28-64-06887-g85390a8-dirty #4
Call Trace:
[<ffffffff803e8d3e>] debug_smp_processor_id+0xee/0xf0
[<ffffffff8021e7f5>] powernowk8_target+0xc5/0x7a0
[<ffffffff804f2b7c>] __cpufreq_driver_target+0x3c/0x40
[<ffffffff804f5878>] cpufreq_governor_performance+0x28/0x30
[<ffffffff804f2cf1>] __cpufreq_governor+0xd1/0x150
[<ffffffff804f3090>] __cpufreq_set_policy+0x170/0x1a0
[<ffffffff804f3dd9>] store_scaling_governor+0xc9/0x270
[<ffffffff805b81e5>] ? _spin_unlock_irqrestore+0x65/0x80
[<ffffffff804f4db0>] ? handle_update+0x0/0x10
[<ffffffff805b81c2>] ? _spin_unlock_irqrestore+0x42/0x80
[<ffffffff804f4c60>] store+0x70/0xb0
[<ffffffff803544da>] sysfs_write_file+0xca/0x140
[<ffffffff802f9beb>] vfs_write+0xcb/0x190
[<ffffffff802f9da0>] sys_write+0x50/0x90
[<ffffffff8020c5db>] system_call_fastpath+0x16/0x1b
BUG: using smp_processor_id() in preemptible [00000000] code: cpufreq-set/4050
caller is powernowk8_target+0xc5/0x7a0
Pid: 4050, comm: cpufreq-set Not tainted 2.6.28-64-06887-g85390a8-dirty #4
Call Trace:
[<ffffffff803e8d3e>] debug_smp_processor_id+0xee/0xf0
[<ffffffff8021e7f5>] powernowk8_target+0xc5/0x7a0
[<ffffffff804f2b7c>] __cpufreq_driver_target+0x3c/0x40
[<ffffffff804f5878>] cpufreq_governor_performance+0x28/0x30
[<ffffffff804f2cf1>] __cpufreq_governor+0xd1/0x150
[<ffffffff804f3090>] __cpufreq_set_policy+0x170/0x1a0
[<ffffffff804f3dd9>] store_scaling_governor+0xc9/0x270
[<ffffffff805b81e5>] ? _spin_unlock_irqrestore+0x65/0x80
[<ffffffff804f4db0>] ? handle_update+0x0/0x10
[<ffffffff805b81c2>] ? _spin_unlock_irqrestore+0x42/0x80
[<ffffffff804f4c60>] store+0x70/0xb0
[<ffffffff803544da>] sysfs_write_file+0xca/0x140
[<ffffffff802f9beb>] vfs_write+0xcb/0x190
[<ffffffff802f9da0>] sys_write+0x50/0x90
[<ffffffff8020c5db>] system_call_fastpath+0x16/0x1b
BUG: using smp_processor_id() in preemptible [00000000] code: cpufreq-set/4051
caller is powernowk8_target+0xc5/0x7a0
Pid: 4051, comm: cpufreq-set Not tainted 2.6.28-64-06887-g85390a8-dirty #4
Call Trace:
[<ffffffff803e8d3e>] debug_smp_processor_id+0xee/0xf0
[<ffffffff8021e7f5>] powernowk8_target+0xc5/0x7a0
[<ffffffff804f2b7c>] __cpufreq_driver_target+0x3c/0x40
[<ffffffff804f5878>] cpufreq_governor_performance+0x28/0x30
[<ffffffff804f2cf1>] __cpufreq_governor+0xd1/0x150
[<ffffffff804f3090>] __cpufreq_set_policy+0x170/0x1a0
[<ffffffff804f3dd9>] store_scaling_governor+0xc9/0x270
[<ffffffff805b81e5>] ? _spin_unlock_irqrestore+0x65/0x80
[<ffffffff804f4db0>] ? handle_update+0x0/0x10
[<ffffffff805b81c2>] ? _spin_unlock_irqrestore+0x42/0x80
[<ffffffff804f4c60>] store+0x70/0xb0
[<ffffffff803544da>] sysfs_write_file+0xca/0x140
[<ffffffff802f9beb>] vfs_write+0xcb/0x190
[<ffffffff802f9da0>] sys_write+0x50/0x90
[<ffffffff8020c5db>] system_call_fastpath+0x16/0x1b
lp0: using parport0 (interrupt-driven).
ppdev: user-space parallel port driver
NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory
NFSD: starting 90-second grace period
Loading iSCSI transport class v2.0-870.
iscsi: registered transport (tcp)
warning: `ntpd' uses 32-bit capabilities (legacy support in use)
Bluetooth: Core ver 2.14
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP ver 2.11
Bluetooth: L2CAP socket layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM ver 1.10
ip_tables: (C) 2000-2006 Netfilter Core Team
nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use
nf_conntrack.acct=1 kernel paramater, acct=1 nf_conntrack module option or
sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
=============================================
[ INFO: possible recursive locking detected ]
2.6.28-64-06887-g85390a8-dirty #4
---------------------------------------------
nfsd4/4336 is trying to acquire lock:
(&type->i_mutex_dir_key#2){--..}, at: [<ffffffff8031ca24>] vfs_fsync+0x84/0x100
but task is already holding lock:
(&type->i_mutex_dir_key#2){--..}, at: [<ffffffffa102a20d>] nfsd4_sync_rec_dir+0x1d/0x50 [nfsd]
other info that might help us debug this:
4 locks held by nfsd4/4336:
#0: (nfsd4){--..}, at: [<ffffffff802628d3>] run_workqueue+0xb3/0x250
#1: ((laundromat_work).work){--..}, at: [<ffffffff802628d3>] run_workqueue+0xb3/0x250
#2: (client_mutex){--..}, at: [<ffffffffa1024d6e>] laundromat_main+0x2e/0x300 [nfsd]
#3: (&type->i_mutex_dir_key#2){--..}, at: [<ffffffffa102a20d>] nfsd4_sync_rec_dir+0x1d/0x50 [nfsd]
stack backtrace:
Pid: 4336, comm: nfsd4 Not tainted 2.6.28-64-06887-g85390a8-dirty #4
Call Trace:
[<ffffffff8027a4b4>] __lock_acquire+0x10c4/0x1dc0
[<ffffffff80212c09>] ? native_sched_clock+0x39/0xa0
[<ffffffff80275d54>] ? get_lock_stats+0x34/0x80
[<ffffffff8027b4ab>] ? lock_acquired+0x15b/0x330
[<ffffffff8027b206>] lock_acquire+0x56/0x80
[<ffffffff8031ca24>] ? vfs_fsync+0x84/0x100
[<ffffffff805b5fcc>] mutex_lock_nested+0xec/0x390
[<ffffffff8031ca24>] ? vfs_fsync+0x84/0x100
[<ffffffff8031ca24>] ? vfs_fsync+0x84/0x100
[<ffffffff8031ca24>] vfs_fsync+0x84/0x100
[<ffffffffa1024d40>] ? laundromat_main+0x0/0x300 [nfsd]
[<ffffffffa100ca70>] nfsd_sync_dir+0x10/0x20 [nfsd]
[<ffffffffa102a219>] nfsd4_sync_rec_dir+0x29/0x50 [nfsd]
[<ffffffffa102a2c5>] nfsd4_recdir_purge_old+0x85/0x90 [nfsd]
[<ffffffffa1024d40>] ? laundromat_main+0x0/0x300 [nfsd]
[<ffffffffa1024d99>] laundromat_main+0x59/0x300 [nfsd]
[<ffffffffa1024d40>] ? laundromat_main+0x0/0x300 [nfsd]
[<ffffffffa1024d40>] ? laundromat_main+0x0/0x300 [nfsd]
[<ffffffff80262925>] run_workqueue+0x105/0x250
[<ffffffff802628d3>] ? run_workqueue+0xb3/0x250
[<ffffffff805bbf78>] ? sub_preempt_count+0xd8/0x140
[<ffffffff80262b17>] worker_thread+0xa7/0x120
[<ffffffff802673d0>] ? autoremove_wake_function+0x0/0x40
[<ffffffff80262a70>] ? worker_thread+0x0/0x120
[<ffffffff80266f09>] kthread+0x49/0x80
[<ffffffff8020d6fa>] child_rip+0xa/0x20
[<ffffffff80247358>] ? finish_task_switch+0x68/0xe0
[<ffffffff805b8156>] ? _spin_unlock_irq+0x36/0x60
[<ffffffff8020d0c0>] ? restore_args+0x0/0x30
[<ffffffff80266ec0>] ? kthread+0x0/0x80
[<ffffffff8020d6f0>] ? child_rip+0x0/0x20
INFO: task nfsd4:4336 blocked for more than 480 seconds.
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
nfsd4 D ffff880083a38c00 0 4336 2
ffff88011e4ddcd0 0000000000000046 ffff88011e474960 ffffffff80212c09
ffffffff809e2000 ffffffff80baac00 0000000000000003 ffff88011e474960
ffff88007f16a4b0 ffff88011e474ed8 000000038027b8dc 00000000ffffd283
Call Trace:
[<ffffffff80212c09>] ? native_sched_clock+0x39/0xa0
[<ffffffff805bbf78>] ? sub_preempt_count+0xd8/0x140
[<ffffffff805b6115>] ? mutex_lock_nested+0x235/0x390
[<ffffffff805b6071>] mutex_lock_nested+0x191/0x390
[<ffffffff8031ca24>] ? vfs_fsync+0x84/0x100
[<ffffffff8031ca24>] ? vfs_fsync+0x84/0x100
[<ffffffff8031ca24>] vfs_fsync+0x84/0x100
[<ffffffffa1024d40>] ? laundromat_main+0x0/0x300 [nfsd]
[<ffffffffa100ca70>] nfsd_sync_dir+0x10/0x20 [nfsd]
[<ffffffffa102a219>] nfsd4_sync_rec_dir+0x29/0x50 [nfsd]
[<ffffffffa102a2c5>] nfsd4_recdir_purge_old+0x85/0x90 [nfsd]
[<ffffffffa1024d40>] ? laundromat_main+0x0/0x300 [nfsd]
[<ffffffffa1024d99>] laundromat_main+0x59/0x300 [nfsd]
[<ffffffffa1024d40>] ? laundromat_main+0x0/0x300 [nfsd]
[<ffffffffa1024d40>] ? laundromat_main+0x0/0x300 [nfsd]
[<ffffffff80262925>] run_workqueue+0x105/0x250
[<ffffffff802628d3>] ? run_workqueue+0xb3/0x250
[<ffffffff805bbf78>] ? sub_preempt_count+0xd8/0x140
[<ffffffff80262b17>] worker_thread+0xa7/0x120
[<ffffffff802673d0>] ? autoremove_wake_function+0x0/0x40
[<ffffffff80262a70>] ? worker_thread+0x0/0x120
[<ffffffff80266f09>] kthread+0x49/0x80
[<ffffffff8020d6fa>] child_rip+0xa/0x20
[<ffffffff80247358>] ? finish_task_switch+0x68/0xe0
[<ffffffff805b8156>] ? _spin_unlock_irq+0x36/0x60
[<ffffffff8020d0c0>] ? restore_args+0x0/0x30
[<ffffffff80266ec0>] ? kthread+0x0/0x80
[<ffffffff8020d6f0>] ? child_rip+0x0/0x20
INFO: lockdep is turned off.
INFO: task nfsd4:4336 blocked for more than 480 seconds.
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
nfsd4 D ffff880083a38c00 0 4336 2
ffff88011e4ddcd0 0000000000000046 ffff88011e474960 ffffffff80212c09
ffffffff809e2000 ffffffff80baac00 0000000000000003 ffff88011e474960
ffff88007f16a4b0 ffff88011e474ed8 000000038027b8dc 00000000ffffd283
Call Trace:
[<ffffffff80212c09>] ? native_sched_clock+0x39/0xa0
[<ffffffff805bbf78>] ? sub_preempt_count+0xd8/0x140
[<ffffffff805b6115>] ? mutex_lock_nested+0x235/0x390
[<ffffffff805b6071>] mutex_lock_nested+0x191/0x390
[<ffffffff8031ca24>] ? vfs_fsync+0x84/0x100
[<ffffffff8031ca24>] ? vfs_fsync+0x84/0x100
[<ffffffff8031ca24>] vfs_fsync+0x84/0x100
[<ffffffffa1024d40>] ? laundromat_main+0x0/0x300 [nfsd]
[<ffffffffa100ca70>] nfsd_sync_dir+0x10/0x20 [nfsd]
[<ffffffffa102a219>] nfsd4_sync_rec_dir+0x29/0x50 [nfsd]
[<ffffffffa102a2c5>] nfsd4_recdir_purge_old+0x85/0x90 [nfsd]
[<ffffffffa1024d40>] ? laundromat_main+0x0/0x300 [nfsd]
[<ffffffffa1024d99>] laundromat_main+0x59/0x300 [nfsd]
[<ffffffffa1024d40>] ? laundromat_main+0x0/0x300 [nfsd]
[<ffffffffa1024d40>] ? laundromat_main+0x0/0x300 [nfsd]
[<ffffffff80262925>] run_workqueue+0x105/0x250
[<ffffffff802628d3>] ? run_workqueue+0xb3/0x250
[<ffffffff805bbf78>] ? sub_preempt_count+0xd8/0x140
[<ffffffff80262b17>] worker_thread+0xa7/0x120
[<ffffffff802673d0>] ? autoremove_wake_function+0x0/0x40
[<ffffffff80262a70>] ? worker_thread+0x0/0x120
[<ffffffff80266f09>] kthread+0x49/0x80
[<ffffffff8020d6fa>] child_rip+0xa/0x20
[<ffffffff80247358>] ? finish_task_switch+0x68/0xe0
[<ffffffff805b8156>] ? _spin_unlock_irq+0x36/0x60
[<ffffffff8020d0c0>] ? restore_args+0x0/0x30
[<ffffffff80266ec0>] ? kthread+0x0/0x80
[<ffffffff8020d6f0>] ? child_rip+0x0/0x20
INFO: lockdep is turned off.
INFO: task nfsd4:4336 blocked for more than 480 seconds.
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
nfsd4 D ffff880083a38c00 0 4336 2
ffff88011e4ddcd0 0000000000000046 ffff88011e474960 ffffffff80212c09
ffffffff809e2000 ffffffff80baac00 0000000000000003 ffff88011e474960
ffff88007f16a4b0 ffff88011e474ed8 000000038027b8dc 00000000ffffd283
Call Trace:
[<ffffffff80212c09>] ? native_sched_clock+0x39/0xa0
[<ffffffff805bbf78>] ? sub_preempt_count+0xd8/0x140
[<ffffffff805b6115>] ? mutex_lock_nested+0x235/0x390
[<ffffffff805b6071>] mutex_lock_nested+0x191/0x390
[<ffffffff8031ca24>] ? vfs_fsync+0x84/0x100
[<ffffffff8031ca24>] ? vfs_fsync+0x84/0x100
[<ffffffff8031ca24>] vfs_fsync+0x84/0x100
[<ffffffffa1024d40>] ? laundromat_main+0x0/0x300 [nfsd]
[<ffffffffa100ca70>] nfsd_sync_dir+0x10/0x20 [nfsd]
[<ffffffffa102a219>] nfsd4_sync_rec_dir+0x29/0x50 [nfsd]
[<ffffffffa102a2c5>] nfsd4_recdir_purge_old+0x85/0x90 [nfsd]
[<ffffffffa1024d40>] ? laundromat_main+0x0/0x300 [nfsd]
[<ffffffffa1024d99>] laundromat_main+0x59/0x300 [nfsd]
[<ffffffffa1024d40>] ? laundromat_main+0x0/0x300 [nfsd]
[<ffffffffa1024d40>] ? laundromat_main+0x0/0x300 [nfsd]
[<ffffffff80262925>] run_workqueue+0x105/0x250
[<ffffffff802628d3>] ? run_workqueue+0xb3/0x250
[<ffffffff805bbf78>] ? sub_preempt_count+0xd8/0x140
[<ffffffff80262b17>] worker_thread+0xa7/0x120
[<ffffffff802673d0>] ? autoremove_wake_function+0x0/0x40
[<ffffffff80262a70>] ? worker_thread+0x0/0x120
[<ffffffff80266f09>] kthread+0x49/0x80
[<ffffffff8020d6fa>] child_rip+0xa/0x20
[<ffffffff80247358>] ? finish_task_switch+0x68/0xe0
[<ffffffff805b8156>] ? _spin_unlock_irq+0x36/0x60
[<ffffffff8020d0c0>] ? restore_args+0x0/0x30
[<ffffffff80266ec0>] ? kthread+0x0/0x80
[<ffffffff8020d6f0>] ? child_rip+0x0/0x20
INFO: lockdep is turned off.
INFO: task nfsd4:4336 blocked for more than 480 seconds.
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
nfsd4 D ffff880083a38c00 0 4336 2
ffff88011e4ddcd0 0000000000000046 ffff88011e474960 ffffffff80212c09
ffffffff809e2000 ffffffff80baac00 0000000000000003 ffff88011e474960
ffff88007f16a4b0 ffff88011e474ed8 000000038027b8dc 00000000ffffd283
Call Trace:
[<ffffffff80212c09>] ? native_sched_clock+0x39/0xa0
[<ffffffff805bbf78>] ? sub_preempt_count+0xd8/0x140
[<ffffffff805b6115>] ? mutex_lock_nested+0x235/0x390
[<ffffffff805b6071>] mutex_lock_nested+0x191/0x390
[<ffffffff8031ca24>] ? vfs_fsync+0x84/0x100
[<ffffffff8031ca24>] ? vfs_fsync+0x84/0x100
[<ffffffff8031ca24>] vfs_fsync+0x84/0x100
[<ffffffffa1024d40>] ? laundromat_main+0x0/0x300 [nfsd]
[<ffffffffa100ca70>] nfsd_sync_dir+0x10/0x20 [nfsd]
[<ffffffffa102a219>] nfsd4_sync_rec_dir+0x29/0x50 [nfsd]
[<ffffffffa102a2c5>] nfsd4_recdir_purge_old+0x85/0x90 [nfsd]
[<ffffffffa1024d40>] ? laundromat_main+0x0/0x300 [nfsd]
[<ffffffffa1024d99>] laundromat_main+0x59/0x300 [nfsd]
[<ffffffffa1024d40>] ? laundromat_main+0x0/0x300 [nfsd]
[<ffffffffa1024d40>] ? laundromat_main+0x0/0x300 [nfsd]
[<ffffffff80262925>] run_workqueue+0x105/0x250
[<ffffffff802628d3>] ? run_workqueue+0xb3/0x250
[<ffffffff805bbf78>] ? sub_preempt_count+0xd8/0x140
[<ffffffff80262b17>] worker_thread+0xa7/0x120
[<ffffffff802673d0>] ? autoremove_wake_function+0x0/0x40
[<ffffffff80262a70>] ? worker_thread+0x0/0x120
[<ffffffff80266f09>] kthread+0x49/0x80
[<ffffffff8020d6fa>] child_rip+0xa/0x20
[<ffffffff80247358>] ? finish_task_switch+0x68/0xe0
[<ffffffff805b8156>] ? _spin_unlock_irq+0x36/0x60
[<ffffffff8020d0c0>] ? restore_args+0x0/0x30
[<ffffffff80266ec0>] ? kthread+0x0/0x80
[<ffffffff8020d6f0>] ? child_rip+0x0/0x20
INFO: lockdep is turned off.
INFO: task nfsd4:4336 blocked for more than 480 seconds.
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
nfsd4 D ffff880083a38c00 0 4336 2
ffff88011e4ddcd0 0000000000000046 ffff88011e474960 ffffffff80212c09
ffffffff809e2000 ffffffff80baac00 0000000000000003 ffff88011e474960
ffff88007f16a4b0 ffff88011e474ed8 000000038027b8dc 00000000ffffd283
Call Trace:
[<ffffffff80212c09>] ? native_sched_clock+0x39/0xa0
[<ffffffff805bbf78>] ? sub_preempt_count+0xd8/0x140
[<ffffffff805b6115>] ? mutex_lock_nested+0x235/0x390
[<ffffffff805b6071>] mutex_lock_nested+0x191/0x390
[<ffffffff8031ca24>] ? vfs_fsync+0x84/0x100
[<ffffffff8031ca24>] ? vfs_fsync+0x84/0x100
[<ffffffff8031ca24>] vfs_fsync+0x84/0x100
[<ffffffffa1024d40>] ? laundromat_main+0x0/0x300 [nfsd]
[<ffffffffa100ca70>] nfsd_sync_dir+0x10/0x20 [nfsd]
[<ffffffffa102a219>] nfsd4_sync_rec_dir+0x29/0x50 [nfsd]
[<ffffffffa102a2c5>] nfsd4_recdir_purge_old+0x85/0x90 [nfsd]
[<ffffffffa1024d40>] ? laundromat_main+0x0/0x300 [nfsd]
[<ffffffffa1024d99>] laundromat_main+0x59/0x300 [nfsd]
[<ffffffffa1024d40>] ? laundromat_main+0x0/0x300 [nfsd]
[<ffffffffa1024d40>] ? laundromat_main+0x0/0x300 [nfsd]
[<ffffffff80262925>] run_workqueue+0x105/0x250
[<ffffffff802628d3>] ? run_workqueue+0xb3/0x250
[<ffffffff805bbf78>] ? sub_preempt_count+0xd8/0x140
[<ffffffff80262b17>] worker_thread+0xa7/0x120
[<ffffffff802673d0>] ? autoremove_wake_function+0x0/0x40
[<ffffffff80262a70>] ? worker_thread+0x0/0x120
[<ffffffff80266f09>] kthread+0x49/0x80
[<ffffffff8020d6fa>] child_rip+0xa/0x20
[<ffffffff80247358>] ? finish_task_switch+0x68/0xe0
[<ffffffff805b8156>] ? _spin_unlock_irq+0x36/0x60
[<ffffffff8020d0c0>] ? restore_args+0x0/0x30
[<ffffffff80266ec0>] ? kthread+0x0/0x80
[<ffffffff8020d6f0>] ? child_rip+0x0/0x20
INFO: lockdep is turned off.
INFO: task nfsd4:4336 blocked for more than 480 seconds.
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
nfsd4 D ffff880083a38c00 0 4336 2
ffff88011e4ddcd0 0000000000000046 ffff88011e474960 ffffffff80212c09
ffffffff809e2000 ffffffff80baac00 0000000000000003 ffff88011e474960
ffff88007f16a4b0 ffff88011e474ed8 000000038027b8dc 00000000ffffd283
Call Trace:
[<ffffffff80212c09>] ? native_sched_clock+0x39/0xa0
[<ffffffff805bbf78>] ? sub_preempt_count+0xd8/0x140
[<ffffffff805b6115>] ? mutex_lock_nested+0x235/0x390
[<ffffffff805b6071>] mutex_lock_nested+0x191/0x390
[<ffffffff8031ca24>] ? vfs_fsync+0x84/0x100
[<ffffffff8031ca24>] ? vfs_fsync+0x84/0x100
[<ffffffff8031ca24>] vfs_fsync+0x84/0x100
[<ffffffffa1024d40>] ? laundromat_main+0x0/0x300 [nfsd]
[<ffffffffa100ca70>] nfsd_sync_dir+0x10/0x20 [nfsd]
[<ffffffffa102a219>] nfsd4_sync_rec_dir+0x29/0x50 [nfsd]
[<ffffffffa102a2c5>] nfsd4_recdir_purge_old+0x85/0x90 [nfsd]
[<ffffffffa1024d40>] ? laundromat_main+0x0/0x300 [nfsd]
[<ffffffffa1024d99>] laundromat_main+0x59/0x300 [nfsd]
[<ffffffffa1024d40>] ? laundromat_main+0x0/0x300 [nfsd]
[<ffffffffa1024d40>] ? laundromat_main+0x0/0x300 [nfsd]
[<ffffffff80262925>] run_workqueue+0x105/0x250
[<ffffffff802628d3>] ? run_workqueue+0xb3/0x250
[<ffffffff805bbf78>] ? sub_preempt_count+0xd8/0x140
[<ffffffff80262b17>] worker_thread+0xa7/0x120
[<ffffffff802673d0>] ? autoremove_wake_function+0x0/0x40
[<ffffffff80262a70>] ? worker_thread+0x0/0x120
[<ffffffff80266f09>] kthread+0x49/0x80
[<ffffffff8020d6fa>] child_rip+0xa/0x20
[<ffffffff80247358>] ? finish_task_switch+0x68/0xe0
[<ffffffff805b8156>] ? _spin_unlock_irq+0x36/0x60
[<ffffffff8020d0c0>] ? restore_args+0x0/0x30
[<ffffffff80266ec0>] ? kthread+0x0/0x80
[<ffffffff8020d6f0>] ? child_rip+0x0/0x20
INFO: lockdep is turned off.
INFO: task nfsd4:4336 blocked for more than 480 seconds.
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
nfsd4 D ffff880083a38c00 0 4336 2
ffff88011e4ddcd0 0000000000000046 ffff88011e474960 ffffffff80212c09
ffffffff809e2000 ffffffff80baac00 0000000000000003 ffff88011e474960
ffff88007f16a4b0 ffff88011e474ed8 000000038027b8dc 00000000ffffd283
Call Trace:
[<ffffffff80212c09>] ? native_sched_clock+0x39/0xa0
[<ffffffff805bbf78>] ? sub_preempt_count+0xd8/0x140
[<ffffffff805b6115>] ? mutex_lock_nested+0x235/0x390
[<ffffffff805b6071>] mutex_lock_nested+0x191/0x390
[<ffffffff8031ca24>] ? vfs_fsync+0x84/0x100
[<ffffffff8031ca24>] ? vfs_fsync+0x84/0x100
[<ffffffff8031ca24>] vfs_fsync+0x84/0x100
[<ffffffffa1024d40>] ? laundromat_main+0x0/0x300 [nfsd]
[<ffffffffa100ca70>] nfsd_sync_dir+0x10/0x20 [nfsd]
[<ffffffffa102a219>] nfsd4_sync_rec_dir+0x29/0x50 [nfsd]
[<ffffffffa102a2c5>] nfsd4_recdir_purge_old+0x85/0x90 [nfsd]
[<ffffffffa1024d40>] ? laundromat_main+0x0/0x300 [nfsd]
[<ffffffffa1024d99>] laundromat_main+0x59/0x300 [nfsd]
[<ffffffffa1024d40>] ? laundromat_main+0x0/0x300 [nfsd]
[<ffffffffa1024d40>] ? laundromat_main+0x0/0x300 [nfsd]
[<ffffffff80262925>] run_workqueue+0x105/0x250
[<ffffffff802628d3>] ? run_workqueue+0xb3/0x250
[<ffffffff805bbf78>] ? sub_preempt_count+0xd8/0x140
[<ffffffff80262b17>] worker_thread+0xa7/0x120
[<ffffffff802673d0>] ? autoremove_wake_function+0x0/0x40
[<ffffffff80262a70>] ? worker_thread+0x0/0x120
[<ffffffff80266f09>] kthread+0x49/0x80
[<ffffffff8020d6fa>] child_rip+0xa/0x20
[<ffffffff80247358>] ? finish_task_switch+0x68/0xe0
[<ffffffff805b8156>] ? _spin_unlock_irq+0x36/0x60
[<ffffffff8020d0c0>] ? restore_args+0x0/0x30
[<ffffffff80266ec0>] ? kthread+0x0/0x80
[<ffffffff8020d6f0>] ? child_rip+0x0/0x20
INFO: lockdep is turned off.
INFO: task nfsd4:4336 blocked for more than 480 seconds.
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
nfsd4 D ffff880083a38c00 0 4336 2
ffff88011e4ddcd0 0000000000000046 ffff88011e474960 ffffffff80212c09
ffffffff809e2000 ffffffff80baac00 0000000000000003 ffff88011e474960
ffff88007f16a4b0 ffff88011e474ed8 000000038027b8dc 00000000ffffd283
Call Trace:
[<ffffffff80212c09>] ? native_sched_clock+0x39/0xa0
[<ffffffff805bbf78>] ? sub_preempt_count+0xd8/0x140
[<ffffffff805b6115>] ? mutex_lock_nested+0x235/0x390
[<ffffffff805b6071>] mutex_lock_nested+0x191/0x390
[<ffffffff8031ca24>] ? vfs_fsync+0x84/0x100
[<ffffffff8031ca24>] ? vfs_fsync+0x84/0x100
[<ffffffff8031ca24>] vfs_fsync+0x84/0x100
[<ffffffffa1024d40>] ? laundromat_main+0x0/0x300 [nfsd]
[<ffffffffa100ca70>] nfsd_sync_dir+0x10/0x20 [nfsd]
[<ffffffffa102a219>] nfsd4_sync_rec_dir+0x29/0x50 [nfsd]
[<ffffffffa102a2c5>] nfsd4_recdir_purge_old+0x85/0x90 [nfsd]
[<ffffffffa1024d40>] ? laundromat_main+0x0/0x300 [nfsd]
[<ffffffffa1024d99>] laundromat_main+0x59/0x300 [nfsd]
[<ffffffffa1024d40>] ? laundromat_main+0x0/0x300 [nfsd]
[<ffffffffa1024d40>] ? laundromat_main+0x0/0x300 [nfsd]
[<ffffffff80262925>] run_workqueue+0x105/0x250
[<ffffffff802628d3>] ? run_workqueue+0xb3/0x250
[<ffffffff805bbf78>] ? sub_preempt_count+0xd8/0x140
[<ffffffff80262b17>] worker_thread+0xa7/0x120
[<ffffffff802673d0>] ? autoremove_wake_function+0x0/0x40
[<ffffffff80262a70>] ? worker_thread+0x0/0x120
[<ffffffff80266f09>] kthread+0x49/0x80
[<ffffffff8020d6fa>] child_rip+0xa/0x20
[<ffffffff80247358>] ? finish_task_switch+0x68/0xe0
[<ffffffff805b8156>] ? _spin_unlock_irq+0x36/0x60
[<ffffffff8020d0c0>] ? restore_args+0x0/0x30
[<ffffffff80266ec0>] ? kthread+0x0/0x80
[<ffffffff8020d6f0>] ? child_rip+0x0/0x20
INFO: lockdep is turned off.
INFO: task nfsd4:4336 blocked for more than 480 seconds.
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
nfsd4 D ffff880083a38c00 0 4336 2
ffff88011e4ddcd0 0000000000000046 ffff88011e474960 ffffffff80212c09
ffffffff809e2000 ffffffff80baac00 0000000000000003 ffff88011e474960
ffff88007f16a4b0 ffff88011e474ed8 000000038027b8dc 00000000ffffd283
Call Trace:
[<ffffffff80212c09>] ? native_sched_clock+0x39/0xa0
[<ffffffff805bbf78>] ? sub_preempt_count+0xd8/0x140
[<ffffffff805b6115>] ? mutex_lock_nested+0x235/0x390
[<ffffffff805b6071>] mutex_lock_nested+0x191/0x390
[<ffffffff8031ca24>] ? vfs_fsync+0x84/0x100
[<ffffffff8031ca24>] ? vfs_fsync+0x84/0x100
[<ffffffff8031ca24>] vfs_fsync+0x84/0x100
[<ffffffffa1024d40>] ? laundromat_main+0x0/0x300 [nfsd]
[<ffffffffa100ca70>] nfsd_sync_dir+0x10/0x20 [nfsd]
[<ffffffffa102a219>] nfsd4_sync_rec_dir+0x29/0x50 [nfsd]
[<ffffffffa102a2c5>] nfsd4_recdir_purge_old+0x85/0x90 [nfsd]
[<ffffffffa1024d40>] ? laundromat_main+0x0/0x300 [nfsd]
[<ffffffffa1024d99>] laundromat_main+0x59/0x300 [nfsd]
[<ffffffffa1024d40>] ? laundromat_main+0x0/0x300 [nfsd]
[<ffffffffa1024d40>] ? laundromat_main+0x0/0x300 [nfsd]
[<ffffffff80262925>] run_workqueue+0x105/0x250
[<ffffffff802628d3>] ? run_workqueue+0xb3/0x250
[<ffffffff805bbf78>] ? sub_preempt_count+0xd8/0x140
[<ffffffff80262b17>] worker_thread+0xa7/0x120
[<ffffffff802673d0>] ? autoremove_wake_function+0x0/0x40
[<ffffffff80262a70>] ? worker_thread+0x0/0x120
[<ffffffff80266f09>] kthread+0x49/0x80
[<ffffffff8020d6fa>] child_rip+0xa/0x20
[<ffffffff80247358>] ? finish_task_switch+0x68/0xe0
[<ffffffff805b8156>] ? _spin_unlock_irq+0x36/0x60
[<ffffffff8020d0c0>] ? restore_args+0x0/0x30
[<ffffffff80266ec0>] ? kthread+0x0/0x80
[<ffffffff8020d6f0>] ? child_rip+0x0/0x20
INFO: lockdep is turned off.
INFO: task nfsd4:4336 blocked for more than 480 seconds.
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
nfsd4 D ffff880083a38c00 0 4336 2
ffff88011e4ddcd0 0000000000000046 ffff88011e474960 ffffffff80212c09
ffffffff809e2000 ffffffff80baac00 0000000000000003 ffff88011e474960
ffff88007f16a4b0 ffff88011e474ed8 000000038027b8dc 00000000ffffd283
Call Trace:
[<ffffffff80212c09>] ? native_sched_clock+0x39/0xa0
[<ffffffff805bbf78>] ? sub_preempt_count+0xd8/0x140
[<ffffffff805b6115>] ? mutex_lock_nested+0x235/0x390
[<ffffffff805b6071>] mutex_lock_nested+0x191/0x390
[<ffffffff8031ca24>] ? vfs_fsync+0x84/0x100
[<ffffffff8031ca24>] ? vfs_fsync+0x84/0x100
[<ffffffff8031ca24>] vfs_fsync+0x84/0x100
[<ffffffffa1024d40>] ? laundromat_main+0x0/0x300 [nfsd]
[<ffffffffa100ca70>] nfsd_sync_dir+0x10/0x20 [nfsd]
[<ffffffffa102a219>] nfsd4_sync_rec_dir+0x29/0x50 [nfsd]
[<ffffffffa102a2c5>] nfsd4_recdir_purge_old+0x85/0x90 [nfsd]
[<ffffffffa1024d40>] ? laundromat_main+0x0/0x300 [nfsd]
[<ffffffffa1024d99>] laundromat_main+0x59/0x300 [nfsd]
[<ffffffffa1024d40>] ? laundromat_main+0x0/0x300 [nfsd]
[<ffffffffa1024d40>] ? laundromat_main+0x0/0x300 [nfsd]
[<ffffffff80262925>] run_workqueue+0x105/0x250
[<ffffffff802628d3>] ? run_workqueue+0xb3/0x250
[<ffffffff805bbf78>] ? sub_preempt_count+0xd8/0x140
[<ffffffff80262b17>] worker_thread+0xa7/0x120
[<ffffffff802673d0>] ? autoremove_wake_function+0x0/0x40
[<ffffffff80262a70>] ? worker_thread+0x0/0x120
[<ffffffff80266f09>] kthread+0x49/0x80
[<ffffffff8020d6fa>] child_rip+0xa/0x20
[<ffffffff80247358>] ? finish_task_switch+0x68/0xe0
[<ffffffff805b8156>] ? _spin_unlock_irq+0x36/0x60
[<ffffffff8020d0c0>] ? restore_args+0x0/0x30
[<ffffffff80266ec0>] ? kthread+0x0/0x80
[<ffffffff8020d6f0>] ? child_rip+0x0/0x20
INFO: lockdep is turned off.
mtrr: type mismatch for e0000000,10000000 old: write-back new: write-combining
