On 2/8/2024 7:32 PM, Heiner Kallweit wrote:
On 08.02.2024 12:05, Aithal, Srikanth wrote:
On 2/8/2024 4:16 PM, Heiner Kallweit wrote:
On 08.02.2024 09:30, Aithal, Srikanth wrote:
Hi,
On 6.8.0-rc3-next-20240208, the network interfaces are not getting configured.
Thanks for the report. Could you please elaborate on what "not getting
configured" means in detail?
- Any error in any log?
- Any other error message?
- Interface doesn't come up or which specific configuration are you missing?
I am not seeing any errors in the dmesg,
[ 4.019383] tg3 0000:c1:00.0 eth0: Tigon3 [partno(BCM95720) rev 5720000] (PCI Express) MAC address d0:8e:79:bb:95:90
[ 4.019391] tg3 0000:c1:00.0 eth0: attached PHY is 5720C (10/100/1000Base-T Ethernet) (WireSpeed[1], EEE[1])
[ 4.019394] tg3 0000:c1:00.0 eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[1] TSOcap[1]
[ 4.019397] tg3 0000:c1:00.0 eth0: dma_rwctrl[00000001] dma_mask[64-bit]
[ 4.041082] tg3 0000:c1:00.1 eth1: Tigon3 [partno(BCM95720) rev 5720000] (PCI Express) MAC address d0:8e:79:bb:95:91
[ 4.041087] tg3 0000:c1:00.1 eth1: attached PHY is 5720C (10/100/1000Base-T Ethernet) (WireSpeed[1], EEE[1])
[ 4.041090] tg3 0000:c1:00.1 eth1: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[1] TSOcap[1]
[ 4.041092] tg3 0000:c1:00.1 eth1: dma_rwctrl[00000001] dma_mask[64-bit]
[ 4.077483] tg3 0000:c1:00.1 eno8403: renamed from eth1
[ 4.124657] tg3 0000:c1:00.0 eno8303: renamed from eth0
nmcli says interfaces are disconnected:
[root@localhost ~]# nmcli
eno8303: disconnected
"Broadcom and subsidiaries NetXtreme BCM5720"
ethernet (tg3), D0:8E:79:BB:95:90, hw, mtu 1500
eno8403: disconnected
"Broadcom and subsidiaries NetXtreme BCM5720"
ethernet (tg3), D0:8E:79:BB:95:91, hw, mtu 1500
I am attaching host dmesg.
Thanks. dmesg lists no error. Please send output from the following commands.
ip link
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN mode
DEFAULT group default qlen 1000
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
2: eno8303: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc mq state
DOWN mode DEFAULT group default qlen 1000
link/ether d0:8e:79:bb:95:90 brd ff:ff:ff:ff:ff:ff
altname enp193s0f0
3: eno8403: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc mq state
DOWN mode DEFAULT group default qlen 1000
link/ether d0:8e:79:bb:95:91 brd ff:ff:ff:ff:ff:ff
altname enp193s0f1
ethtool <if>
Settings for eno8303:
Supported ports: [ TP ]
Supported link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Half 1000baseT/Full
Supported pause frame use: No
Supports auto-negotiation: Yes
Supported FEC modes: Not reported
Advertised link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Half 1000baseT/Full
Advertised pause frame use: No
Advertised auto-negotiation: Yes
Advertised FEC modes: Not reported
Speed: Unknown!
Duplex: Unknown! (255)
Auto-negotiation: on
Port: Twisted Pair
PHYAD: 1
Transceiver: internal
MDI-X: Unknown
Supports Wake-on: g
Wake-on: d
Current message level: 0x000000ff (255)
drv probe link timer ifdown ifup rx_err
tx_err
Link detected: no
Settings for eno8403:
Supported ports: [ TP ]
Supported link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Half 1000baseT/Full
Supported pause frame use: No
Supports auto-negotiation: Yes
Supported FEC modes: Not reported
Advertised link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Half 1000baseT/Full
Advertised pause frame use: No
Advertised auto-negotiation: Yes
Advertised FEC modes: Not reported
Speed: Unknown!
Duplex: Unknown! (255)
Auto-negotiation: on
Port: Twisted Pair
PHYAD: 2
Transceiver: internal
MDI-X: Unknown
Supports Wake-on: g
Wake-on: d
Current message level: 0x000000ff (255)
drv probe link timer ifdown ifup rx_err
tx_err
Link detected: no
ethtool --show-eee <if>
EEE settings for eno8403:
EEE status: enabled - inactive
Tx LPI: 2047 (us)
Supported EEE link modes: 100baseT/Full
1000baseT/Full
Advertised EEE link modes: 100baseT/Full
1000baseT/Full
Link partner advertised EEE link modes: Not reported
EEE settings for eno8303:
EEE status: enabled - inactive
Tx LPI: 2047 (us)
Supported EEE link modes: 100baseT/Full
1000baseT/Full
Advertised EEE link modes: 100baseT/Full
1000baseT/Full
Link partner advertised EEE link modes: Not reported
If the interfaces aren't up, please try to bring them up manually and see what happens.
ip link set <if> up
Nothing happens.
[root@localhost ~]# ip link set eno8303 up
[root@localhost ~]# ip link set eno8403 up
[root@localhost ~]# ip link
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN mode
DEFAULT group default qlen 1000
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
2: eno8303: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc mq state
DOWN mode DEFAULT group default qlen 1000
link/ether d0:8e:79:bb:95:90 brd ff:ff:ff:ff:ff:ff
altname enp193s0f0
3: eno8403: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc mq state
DOWN mode DEFAULT group default qlen 1000
link/ether d0:8e:79:bb:95:91 brd ff:ff:ff:ff:ff:ff
altname enp193s0f1
I have 'NetXtreme BCM5720 Gigabit Ethernet PCIe'
configuration: autonegotiation=on broadcast=yes driver=tg3
If I revert below commit I am able to get back the interfaces mentioned.
commit 9bc791341bc9a5c22b94889aa37993bb69faa317
Author: Heiner Kallweit <hkallweit1@xxxxxxxxx>
Date: Sat Feb 3 22:12:50 2024 +0100
tg3: convert EEE handling to use linkmode bitmaps
Convert EEE handling to use linkmode bitmaps. This prepares for
removing the legacy bitmaps from struct ethtool_keee.
No functional change intended.
Note: The change to mii_eee_cap1_mod_linkmode_t(tp->eee.advertised, val)
in tg3_phy_autoneg_cfg() isn't completely obvious, but it doesn't change
the current functionality.
Signed-off-by: Heiner Kallweit <hkallweit1@xxxxxxxxx>
Reviewed-by: Andrew Lunn <andrew@xxxxxxx>
Link: https://lore.kernel.org/r/0652b910-6bcc-421f-8769-38f7dae5037e@xxxxxxxxx
Signed-off-by: Jakub Kicinski <kuba@xxxxxxxxxx>
The same works fine on 6.8.0-rc3-next-20240207.
Thanks,
Srikanth Aithal
sraithal@xxxxxxx
Heiner
