[PATCH 1/3] Documentation: Move Oxford Semiconductor PCIe (Tornado) 950 to misc-devices

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Documentation/tty has been moved to driver-api, which is not suitable 
for user documentation, so move the Oxford Semiconductor PCIe (Tornado) 
950 description to misc-devices instead.

Signed-off-by: Maciej W. Rozycki <macro@xxxxxxxxxxx>
---
 Documentation/misc-devices/oxsemi-tornado.rst       |  129 ++++++++++++++++++++
 Documentation/tty/device_drivers/oxsemi-tornado.rst |  129 --------------------
 2 files changed, 129 insertions(+), 129 deletions(-)

linux-doc-oxsemi-tornado-move.diff
Index: linux-macro/Documentation/misc-devices/oxsemi-tornado.rst
===================================================================
--- /dev/null
+++ linux-macro/Documentation/misc-devices/oxsemi-tornado.rst
@@ -0,0 +1,129 @@
+.. SPDX-License-Identifier: GPL-2.0
+
+====================================================================
+Notes on Oxford Semiconductor PCIe (Tornado) 950 serial port devices
+====================================================================
+
+Oxford Semiconductor PCIe (Tornado) 950 serial port devices are driven
+by a fixed 62.5MHz clock input derived from the 100MHz PCI Express clock.
+
+The baud rate produced by the baud generator is obtained from this input
+frequency by dividing it by the clock prescaler, which can be set to any
+value from 1 to 63.875 in increments of 0.125, and then the usual 16-bit
+divisor is used as with the original 8250, to divide the frequency by a
+value from 1 to 65535.  Finally a programmable oversampling rate is used
+that can take any value from 4 to 16 to divide the frequency further and
+determine the actual baud rate used.  Baud rates from 15625000bps down
+to 0.933bps can be obtained this way.
+
+By default the oversampling rate is set to 16 and the clock prescaler is
+set to 33.875, meaning that the frequency to be used as the reference
+for the usual 16-bit divisor is 115313.653, which is close enough to the
+frequency of 115200 used by the original 8250 for the same values to be
+used for the divisor to obtain the requested baud rates by software that
+is unaware of the extra clock controls available.
+
+The oversampling rate is programmed with the TCR register and the clock
+prescaler is programmed with the CPR/CPR2 register pair[1][2][3][4].
+To switch away from the default value of 33.875 for the prescaler the
+the enhanced mode has to be explicitly enabled though, by setting bit 4
+of the EFR.  In that mode setting bit 7 in the MCR enables the prescaler
+or otherwise it is bypassed as if the value of 1 was used.  Additionally
+writing any value to CPR clears CPR2 for compatibility with old software
+written for older conventional PCI Oxford Semiconductor devices that do
+not have the extra prescaler's 9th bit in CPR2, so the CPR/CPR2 register
+pair has to be programmed in the right order.
+
+By using these parameters rates from 15625000bps down to 1bps can be
+obtained, with either exact or highly-accurate actual bit rates for
+standard and many non-standard rates.
+
+Here are the figures for the standard and some non-standard baud rates
+(including those quoted in Oxford Semiconductor documentation), giving
+the requested rate (r), the actual rate yielded (a) and its deviation
+from the requested rate (d), and the values of the oversampling rate
+(tcr), the clock prescaler (cpr) and the divisor (div) produced by the
+new `get_divisor' handler:
+
+r: 15625000, a: 15625000.00, d:  0.0000%, tcr:  4, cpr:  1.000, div:     1
+r: 12500000, a: 12500000.00, d:  0.0000%, tcr:  5, cpr:  1.000, div:     1
+r: 10416666, a: 10416666.67, d:  0.0000%, tcr:  6, cpr:  1.000, div:     1
+r:  8928571, a:  8928571.43, d:  0.0000%, tcr:  7, cpr:  1.000, div:     1
+r:  7812500, a:  7812500.00, d:  0.0000%, tcr:  8, cpr:  1.000, div:     1
+r:  4000000, a:  4000000.00, d:  0.0000%, tcr:  5, cpr:  3.125, div:     1
+r:  3686400, a:  3676470.59, d: -0.2694%, tcr:  8, cpr:  2.125, div:     1
+r:  3500000, a:  3496503.50, d: -0.0999%, tcr: 13, cpr:  1.375, div:     1
+r:  3000000, a:  2976190.48, d: -0.7937%, tcr: 14, cpr:  1.500, div:     1
+r:  2500000, a:  2500000.00, d:  0.0000%, tcr: 10, cpr:  2.500, div:     1
+r:  2000000, a:  2000000.00, d:  0.0000%, tcr: 10, cpr:  3.125, div:     1
+r:  1843200, a:  1838235.29, d: -0.2694%, tcr: 16, cpr:  2.125, div:     1
+r:  1500000, a:  1492537.31, d: -0.4975%, tcr:  5, cpr:  8.375, div:     1
+r:  1152000, a:  1152073.73, d:  0.0064%, tcr: 14, cpr:  3.875, div:     1
+r:   921600, a:   919117.65, d: -0.2694%, tcr: 16, cpr:  2.125, div:     2
+r:   576000, a:   576036.87, d:  0.0064%, tcr: 14, cpr:  3.875, div:     2
+r:   460800, a:   460829.49, d:  0.0064%, tcr:  7, cpr:  3.875, div:     5
+r:   230400, a:   230414.75, d:  0.0064%, tcr: 14, cpr:  3.875, div:     5
+r:   115200, a:   115207.37, d:  0.0064%, tcr: 14, cpr:  1.250, div:    31
+r:    57600, a:    57603.69, d:  0.0064%, tcr:  8, cpr:  3.875, div:    35
+r:    38400, a:    38402.46, d:  0.0064%, tcr: 14, cpr:  3.875, div:    30
+r:    19200, a:    19201.23, d:  0.0064%, tcr:  8, cpr:  3.875, div:   105
+r:     9600, a:     9600.06, d:  0.0006%, tcr:  9, cpr:  1.125, div:   643
+r:     4800, a:     4799.98, d: -0.0004%, tcr:  7, cpr:  2.875, div:   647
+r:     2400, a:     2400.02, d:  0.0008%, tcr:  9, cpr:  2.250, div:  1286
+r:     1200, a:     1200.00, d:  0.0000%, tcr: 14, cpr:  2.875, div:  1294
+r:      300, a:      300.00, d:  0.0000%, tcr: 11, cpr:  2.625, div:  7215
+r:      200, a:      200.00, d:  0.0000%, tcr: 16, cpr:  1.250, div: 15625
+r:      150, a:      150.00, d:  0.0000%, tcr: 13, cpr:  2.250, div: 14245
+r:      134, a:      134.00, d:  0.0000%, tcr: 11, cpr:  2.625, div: 16153
+r:      110, a:      110.00, d:  0.0000%, tcr: 12, cpr:  1.000, div: 47348
+r:       75, a:       75.00, d:  0.0000%, tcr:  4, cpr:  5.875, div: 35461
+r:       50, a:       50.00, d:  0.0000%, tcr: 16, cpr:  1.250, div: 62500
+r:       25, a:       25.00, d:  0.0000%, tcr: 16, cpr:  2.500, div: 62500
+r:        4, a:        4.00, d:  0.0000%, tcr: 16, cpr: 20.000, div: 48828
+r:        2, a:        2.00, d:  0.0000%, tcr: 16, cpr: 40.000, div: 48828
+r:        1, a:        1.00, d:  0.0000%, tcr: 16, cpr: 63.875, div: 61154
+
+With the baud base set to 15625000 and the unsigned 16-bit UART_DIV_MAX
+limitation imposed by `serial8250_get_baud_rate' standard baud rates
+below 300bps become unavailable in the regular way, e.g. the rate of
+200bps requires the baud base to be divided by 78125 and that is beyond
+the unsigned 16-bit range.  The historic spd_cust feature can still be
+used by encoding the values for, the prescaler, the oversampling rate
+and the clock divisor (DLM/DLL) as follows to obtain such rates if so
+required:
+
+ 31 29 28             20 19   16 15                            0
++-----+-----------------+-------+-------------------------------+
+|0 0 0|    CPR2:CPR     |  TCR  |            DLM:DLL            |
++-----+-----------------+-------+-------------------------------+
+
+Use a value such encoded for the `custom_divisor' field along with the
+ASYNC_SPD_CUST flag set in the `flags' field in `struct serial_struct'
+passed with the TIOCSSERIAL ioctl(2), such as with the setserial(8)
+utility and its `divisor' and `spd_cust' parameters, and the select
+the baud rate of 38400bps.  Note that the value of 0 in TCR sets the
+oversampling rate to 16 and prescaler values below 1 in CPR2/CPR are
+clamped by the driver to 1.
+
+For example the value of 0x1f4004e2 will set CPR2/CPR, TCR and DLM/DLL
+respectively to 0x1f4, 0x0 and 0x04e2, choosing the prescaler value,
+the oversampling rate and the clock divisor of 62.500, 16 and 1250
+respectively.  These parameters will set the baud rate for the serial
+port to 62500000 / 62.500 / 1250 / 16 = 50bps.
+
+References:
+
+[1] "OXPCIe200 PCI Express Multi-Port Bridge", Oxford Semiconductor,
+    Inc., DS-0045, 10 Nov 2008, Section "950 Mode", pp. 64-65
+
+[2] "OXPCIe952 PCI Express Bridge to Dual Serial & Parallel Port",
+    Oxford Semiconductor, Inc., DS-0046, Mar 06 08, Section "950 Mode",
+    p. 20
+
+[3] "OXPCIe954 PCI Express Bridge to Quad Serial Port", Oxford
+    Semiconductor, Inc., DS-0047, Feb 08, Section "950 Mode", p. 20
+
+[4] "OXPCIe958 PCI Express Bridge to Octal Serial Port", Oxford
+    Semiconductor, Inc., DS-0048, Feb 08, Section "950 Mode", p. 20
+
+Maciej W. Rozycki  <macro@xxxxxxxxxxx>
Index: linux-macro/Documentation/tty/device_drivers/oxsemi-tornado.rst
===================================================================
--- linux-macro.orig/Documentation/tty/device_drivers/oxsemi-tornado.rst
+++ /dev/null
@@ -1,129 +0,0 @@
-.. SPDX-License-Identifier: GPL-2.0
-
-====================================================================
-Notes on Oxford Semiconductor PCIe (Tornado) 950 serial port devices
-====================================================================
-
-Oxford Semiconductor PCIe (Tornado) 950 serial port devices are driven
-by a fixed 62.5MHz clock input derived from the 100MHz PCI Express clock.
-
-The baud rate produced by the baud generator is obtained from this input
-frequency by dividing it by the clock prescaler, which can be set to any
-value from 1 to 63.875 in increments of 0.125, and then the usual 16-bit
-divisor is used as with the original 8250, to divide the frequency by a
-value from 1 to 65535.  Finally a programmable oversampling rate is used
-that can take any value from 4 to 16 to divide the frequency further and
-determine the actual baud rate used.  Baud rates from 15625000bps down
-to 0.933bps can be obtained this way.
-
-By default the oversampling rate is set to 16 and the clock prescaler is
-set to 33.875, meaning that the frequency to be used as the reference
-for the usual 16-bit divisor is 115313.653, which is close enough to the
-frequency of 115200 used by the original 8250 for the same values to be
-used for the divisor to obtain the requested baud rates by software that
-is unaware of the extra clock controls available.
-
-The oversampling rate is programmed with the TCR register and the clock
-prescaler is programmed with the CPR/CPR2 register pair[1][2][3][4].
-To switch away from the default value of 33.875 for the prescaler the
-the enhanced mode has to be explicitly enabled though, by setting bit 4
-of the EFR.  In that mode setting bit 7 in the MCR enables the prescaler
-or otherwise it is bypassed as if the value of 1 was used.  Additionally
-writing any value to CPR clears CPR2 for compatibility with old software
-written for older conventional PCI Oxford Semiconductor devices that do
-not have the extra prescaler's 9th bit in CPR2, so the CPR/CPR2 register
-pair has to be programmed in the right order.
-
-By using these parameters rates from 15625000bps down to 1bps can be
-obtained, with either exact or highly-accurate actual bit rates for
-standard and many non-standard rates.
-
-Here are the figures for the standard and some non-standard baud rates
-(including those quoted in Oxford Semiconductor documentation), giving
-the requested rate (r), the actual rate yielded (a) and its deviation
-from the requested rate (d), and the values of the oversampling rate
-(tcr), the clock prescaler (cpr) and the divisor (div) produced by the
-new `get_divisor' handler:
-
-r: 15625000, a: 15625000.00, d:  0.0000%, tcr:  4, cpr:  1.000, div:     1
-r: 12500000, a: 12500000.00, d:  0.0000%, tcr:  5, cpr:  1.000, div:     1
-r: 10416666, a: 10416666.67, d:  0.0000%, tcr:  6, cpr:  1.000, div:     1
-r:  8928571, a:  8928571.43, d:  0.0000%, tcr:  7, cpr:  1.000, div:     1
-r:  7812500, a:  7812500.00, d:  0.0000%, tcr:  8, cpr:  1.000, div:     1
-r:  4000000, a:  4000000.00, d:  0.0000%, tcr:  5, cpr:  3.125, div:     1
-r:  3686400, a:  3676470.59, d: -0.2694%, tcr:  8, cpr:  2.125, div:     1
-r:  3500000, a:  3496503.50, d: -0.0999%, tcr: 13, cpr:  1.375, div:     1
-r:  3000000, a:  2976190.48, d: -0.7937%, tcr: 14, cpr:  1.500, div:     1
-r:  2500000, a:  2500000.00, d:  0.0000%, tcr: 10, cpr:  2.500, div:     1
-r:  2000000, a:  2000000.00, d:  0.0000%, tcr: 10, cpr:  3.125, div:     1
-r:  1843200, a:  1838235.29, d: -0.2694%, tcr: 16, cpr:  2.125, div:     1
-r:  1500000, a:  1492537.31, d: -0.4975%, tcr:  5, cpr:  8.375, div:     1
-r:  1152000, a:  1152073.73, d:  0.0064%, tcr: 14, cpr:  3.875, div:     1
-r:   921600, a:   919117.65, d: -0.2694%, tcr: 16, cpr:  2.125, div:     2
-r:   576000, a:   576036.87, d:  0.0064%, tcr: 14, cpr:  3.875, div:     2
-r:   460800, a:   460829.49, d:  0.0064%, tcr:  7, cpr:  3.875, div:     5
-r:   230400, a:   230414.75, d:  0.0064%, tcr: 14, cpr:  3.875, div:     5
-r:   115200, a:   115207.37, d:  0.0064%, tcr: 14, cpr:  1.250, div:    31
-r:    57600, a:    57603.69, d:  0.0064%, tcr:  8, cpr:  3.875, div:    35
-r:    38400, a:    38402.46, d:  0.0064%, tcr: 14, cpr:  3.875, div:    30
-r:    19200, a:    19201.23, d:  0.0064%, tcr:  8, cpr:  3.875, div:   105
-r:     9600, a:     9600.06, d:  0.0006%, tcr:  9, cpr:  1.125, div:   643
-r:     4800, a:     4799.98, d: -0.0004%, tcr:  7, cpr:  2.875, div:   647
-r:     2400, a:     2400.02, d:  0.0008%, tcr:  9, cpr:  2.250, div:  1286
-r:     1200, a:     1200.00, d:  0.0000%, tcr: 14, cpr:  2.875, div:  1294
-r:      300, a:      300.00, d:  0.0000%, tcr: 11, cpr:  2.625, div:  7215
-r:      200, a:      200.00, d:  0.0000%, tcr: 16, cpr:  1.250, div: 15625
-r:      150, a:      150.00, d:  0.0000%, tcr: 13, cpr:  2.250, div: 14245
-r:      134, a:      134.00, d:  0.0000%, tcr: 11, cpr:  2.625, div: 16153
-r:      110, a:      110.00, d:  0.0000%, tcr: 12, cpr:  1.000, div: 47348
-r:       75, a:       75.00, d:  0.0000%, tcr:  4, cpr:  5.875, div: 35461
-r:       50, a:       50.00, d:  0.0000%, tcr: 16, cpr:  1.250, div: 62500
-r:       25, a:       25.00, d:  0.0000%, tcr: 16, cpr:  2.500, div: 62500
-r:        4, a:        4.00, d:  0.0000%, tcr: 16, cpr: 20.000, div: 48828
-r:        2, a:        2.00, d:  0.0000%, tcr: 16, cpr: 40.000, div: 48828
-r:        1, a:        1.00, d:  0.0000%, tcr: 16, cpr: 63.875, div: 61154
-
-With the baud base set to 15625000 and the unsigned 16-bit UART_DIV_MAX
-limitation imposed by `serial8250_get_baud_rate' standard baud rates
-below 300bps become unavailable in the regular way, e.g. the rate of
-200bps requires the baud base to be divided by 78125 and that is beyond
-the unsigned 16-bit range.  The historic spd_cust feature can still be
-used by encoding the values for, the prescaler, the oversampling rate
-and the clock divisor (DLM/DLL) as follows to obtain such rates if so
-required:
-
- 31 29 28             20 19   16 15                            0
-+-----+-----------------+-------+-------------------------------+
-|0 0 0|    CPR2:CPR     |  TCR  |            DLM:DLL            |
-+-----+-----------------+-------+-------------------------------+
-
-Use a value such encoded for the `custom_divisor' field along with the
-ASYNC_SPD_CUST flag set in the `flags' field in `struct serial_struct'
-passed with the TIOCSSERIAL ioctl(2), such as with the setserial(8)
-utility and its `divisor' and `spd_cust' parameters, and the select
-the baud rate of 38400bps.  Note that the value of 0 in TCR sets the
-oversampling rate to 16 and prescaler values below 1 in CPR2/CPR are
-clamped by the driver to 1.
-
-For example the value of 0x1f4004e2 will set CPR2/CPR, TCR and DLM/DLL
-respectively to 0x1f4, 0x0 and 0x04e2, choosing the prescaler value,
-the oversampling rate and the clock divisor of 62.500, 16 and 1250
-respectively.  These parameters will set the baud rate for the serial
-port to 62500000 / 62.500 / 1250 / 16 = 50bps.
-
-References:
-
-[1] "OXPCIe200 PCI Express Multi-Port Bridge", Oxford Semiconductor,
-    Inc., DS-0045, 10 Nov 2008, Section "950 Mode", pp. 64-65
-
-[2] "OXPCIe952 PCI Express Bridge to Dual Serial & Parallel Port",
-    Oxford Semiconductor, Inc., DS-0046, Mar 06 08, Section "950 Mode",
-    p. 20
-
-[3] "OXPCIe954 PCI Express Bridge to Quad Serial Port", Oxford
-    Semiconductor, Inc., DS-0047, Feb 08, Section "950 Mode", p. 20
-
-[4] "OXPCIe958 PCI Express Bridge to Octal Serial Port", Oxford
-    Semiconductor, Inc., DS-0048, Feb 08, Section "950 Mode", p. 20
-
-Maciej W. Rozycki  <macro@xxxxxxxxxxx>



[Index of Archives]     [Linux Kernel]     [Linux USB Development]     [Yosemite News]     [Linux SCSI]

  Powered by Linux