[PATCH v1 0/3] Integrate support for Self save, determine support and preference for self save or restore

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Currently the stop-api supports a mechanism called as self-restore
which allows us to restore the values of certain SPRs on wakeup from a
deep-stop state to a desired value. To use this, the Kernel makes an
OPAL call passing the PIR of the CPU, the SPR number and the value to
which the SPR should be restored when that CPU wakes up from a deep
stop state.

Recently, a new feature, named self-save has been enabled in the
stop-api, which is an alternative mechanism to do the same, except
that self-save will save the current content of the SPR before
entering a deep stop state and also restore the content back on
waking up from a deep stop state.

This patch series aims at introducing and leveraging the self-save feature in
the kernel.

Now, as the kernel has a choice to prefer one mode over the other and
there can be registers in both the save/restore SPR list which are sent
from the device tree, a new interface has been defined for the seamless
handing of the modes for each SPR.

A list of preferred SPRs are maintained in the kernel which contains two
properties:
1. supported_mode: Helps in identifying if it strictly supports self
                   save or restore or both.
2. preferred_mode: Calls out what mode is preferred for each SPR. It
                   could be strictly self save or restore, or it can also
                   determine the preference of  mode over the other if both
                   are present by encapsulating the other in bitmask from
                   LSB to MSB.
Below is a table to show the Scenario::Consequence when the self save and
self restore modes are available or disabled in different combinations as
perceived from the device tree.

SR = Self restore; SS = Self save

.-----------------------------------.----------------------------------------.
|             Scenario              |                Consequence             |
:-----------------------------------+----------------------------------------:
| Legacy Firmware. No SS or SR node | Self restore is called for all         |
|                                   | supported SPRs                         |
:-----------------------------------+----------------------------------------:
| SR: !active SS: !active           | Deep stop states disabled              |
:-----------------------------------+----------------------------------------:
| SR: active SS: !active            | Self restore is called for all         |
|                                   | supported SPRs                         |
:-----------------------------------+----------------------------------------:
| SR: active SS: active             | Goes through the preferences for each  |
|                                   | SPR and executes of the modes          |
|                                   | accordingly. Currently, Self restore is|
|                                   | called for all the SPRs except PSSCR   |
|                                   | which is self saved                    |
:-----------------------------------+----------------------------------------:
| SR: active(only HID0) SS: active  | Self save called for all supported     |
|                                   | registers expect HID0 (as HID0 cannot  |
|                                   | be self saved currently)               |
:-----------------------------------+----------------------------------------:
| SR: !active SS: active            | currently will disable deep states as  |
|                                   | HID0 is needed to be self restored and |
|                                   | cannot be self saved                   |
'-----------------------------------'----------------------------------------'

Pratik Rajesh Sampat (3):
  powerpc/powernv: Interface to define support and preference for a SPR
  powerpc/powernv: Introduce Self save support
  powerpc/powernv: Parse device tree, population of SPR support

 arch/powerpc/include/asm/opal-api.h        |   3 +-
 arch/powerpc/include/asm/opal.h            |   1 +
 arch/powerpc/platforms/powernv/idle.c      | 404 ++++++++++++++++++---
 arch/powerpc/platforms/powernv/opal-call.c |   1 +
 4 files changed, 357 insertions(+), 52 deletions(-)

-- 
2.21.0




[Index of Archives]     [Linux Kernel]     [Linux USB Development]     [Yosemite News]     [Linux SCSI]

  Powered by Linux