Hi 2.6.28-rc3-next-20081103 on sparc64 netconsole on e100 does not work pci 0000:02:01.0: supports D1 D2 pci 0000:02:01.0: PME# supported from D0 D1 D2 D3hot pci 0000:02:01.0: PME# disabled device: '0000:02:01.0': device_add bus: 'pci': add device 0000:02:01.0 pci 0000:02:01.0: calling quirk_e100_interrupt+0x0/0x1e4 pci 0000:02:01.0: calling quirk_cardbus_legacy+0x0/0x40 pci 0000:02:01.0: calling quirk_usb_early_handoff+0x0/0x42c <...> e100: Intel(R) PRO/100 Network Driver, 3.5.23-k4-NAPI e100: Copyright(c) 1999-2006 Intel Corporation bus: 'pci': add driver e100 bus: 'pci': driver_probe_device: matched device 0000:02:01.0 with driver e100 bus: 'pci': really_probe: probing driver e100 with device 0000:02:01.0 PCI: Enabling device: (0000:02:01.0), cmd 3 e100 0000:02:01.0: enabling bus mastering e100 0000:02:01.0: PME# disabled device: 'eth1': device_add e100: eth1: e100_probe: addr 0x1ff00002000, irq 15, MAC addr 00:d0:b7:e4:d6:f1 driver: '0000:02:01.0': driver_bound: bound to device 'e100' bus: 'pci': really_probe: bound device 0000:02:01.0 to driver e100 netconsole: local port 6665 netconsole: local IP 192.168.1.5 netconsole: interface eth1 netconsole: remote port 6667 netconsole: remote IP 192.168.1.3 netconsole: remote ethernet address 00:08:c7:da:88:fb netconsole: device eth1 not up yet, forcing it e100 0000:02:01.0: firmware: requesting e100/d101m_ucode.bin device: '0000:02:01.0': device_add device: '0000:02:01.0': device_unregister e100: eth1: e100_request_firmware: Failed to load firmware "e100/d101m_ucode.bin": -2 netconsole: failed to open eth1 netconsole: cleaning up <...> e100 0000:02:01.0: firmware: requesting e100/d101m_ucode.bin device: '0000:02:01.0': device_add device: '0000:02:01.0': device_unregister e100: eth1: e100_watchdog: link up, 100Mbps, full-duplex netconsole output (less verbose) from 2.6.28-rc3: e100: Intel(R) PRO/100 Network Driver, 3.5.23-k4-NAPI e100: Copyright(c) 1999-2006 Intel Corporation e100 0000:02:01.0: PME# disabled e100: eth1: e100_probe: addr 0x1ff00002000, irq 15, MAC addr 00:d0:b7:e4:d6:f1 netconsole: local port 6665 netconsole: local IP 192.168.1.5 netconsole: interface eth1 netconsole: remote port 6667 netconsole: remote IP 192.168.1.3 netconsole: remote ethernet address 00:08:c7:da:88:fb netconsole: device eth1 not up yet, forcing it e100: eth1: e100_watchdog: link up, 100Mbps, full-duplex netconsole: carrier detect appears untrustworthy, waiting 4 seconds console [netcon0] enabled netconsole: network logging started -- To unsubscribe from this list: send the line "unsubscribe linux-next" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
