First my setup: x86_64 Linux 2.6.20 Asus M2N-E (same problem with an Asus A8N-VM too) chipset MCP55 (nvidia nforce 570 ultra) Realtek 8029 PCI The problem is: I use an old PCI Realtek 8029 card with the old BNC (coaxial) connector and it works perfectly except that after a while (a few hours using it) the system returns the message (some days it won't occur. I can't reproduce it): Mar 7 00:52:48 tux vmunix: NETDEV WATCHDOG: eth0: transmit timed out Mar 7 00:52:48 tux vmunix: eth0: Tx timed out, lost interrupt? TSR=0x3, ISR=0x3, t=1595. Mar 7 00:52:52 tux vmunix: NETDEV WATCHDOG: eth0: transmit timed out Mar 7 00:52:52 tux vmunix: eth0: Tx timed out, lost interrupt? TSR=0x3, ISR=0x3, t=2430. Mar 7 00:52:54 tux vmunix: NETDEV WATCHDOG: eth0: transmit timed out Mar 7 00:52:54 tux vmunix: eth0: Tx timed out, lost interrupt? TSR=0x3, ISR=0x3, t=1195. Mar 7 00:52:56 tux vmunix: NETDEV WATCHDOG: eth0: transmit timed out Mar 7 00:52:56 tux vmunix: eth0: Tx timed out, lost interrupt? TSR=0x3, ISR=0x3, t=1430. Mar 7 00:52:58 tux vmunix: NETDEV WATCHDOG: eth0: transmit timed out Mar 7 00:52:58 tux vmunix: eth0: Tx timed out, lost interrupt? TSR=0x3, ISR=0x3, t=1200. *********************************************************** POSSIBLE SOLUTION/HINT *********************************************************** Then I have to reboot the machine. But I found a ***possible solution*** with my old motherboard (Asus A8N-VM with Athlon64 3800+): I just changed the BIOS value from 800MHz to 400MHz: Hyper Transport MCP51 Configuration MCP51 (SB) to NVIDIA (NB) Frequency: 400MHz and the problem disappears. ************************************************************ Now I have this new motherboard, Asus M2N-E and the problem remains. I don't have this BIOS option (at least I didn't found) and as I don't agree that I have to use a lower frequency to "solve" this, I ask if there could be another solution. I suspect the problem is with the nvidia chipset. I read here: http://en.wikipedia.org/wiki/NForce#Performance_and_Issues Could the nvidia chipset affects the NIC board in some circunstances? Could it be a problem with interrupts? ACPI? A x86_64 issue? Some kernel options I use: [*] Support mmconfig PCI config space access [*] Plug and Play ACPI support (EXPERIMENTAL) Any hints how to debug this problem? Here's more info about my system: fraga@tux ~/src$ cat /proc/interrupts CPU0 CPU1 0: 8823 2062328 IO-APIC-edge timer 1: 26 6544 IO-APIC-edge i8042 8: 0 0 IO-APIC-edge rtc 9: 0 0 IO-APIC-fasteoi acpi 14: 0 19 IO-APIC-edge libata 15: 0 0 IO-APIC-edge libata 16: 650 155281 IO-APIC-fasteoi nvidia 17: 127 40580 IO-APIC-fasteoi eth0 20: 103 39077 IO-APIC-fasteoi ohci_hcd:usb1 21: 0 0 IO-APIC-fasteoi libata 22: 282 77128 IO-APIC-fasteoi libata, HDA Intel 23: 106 19731 IO-APIC-fasteoi libata, ehci_hcd:usb2 NMI: 217 178 LOC: 2071224 2071107 ERR: 0 lspci -vvv 00:00.0 RAM memory: nVidia Corporation MCP55 Memory Controller (rev a1) Subsystem: ASUSTeK Computer Inc. Unknown device 8239 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Capabilities: [44] HyperTransport: Slave or Primary Interface Command: BaseUnitID=0 UnitCnt=15 MastHost- DefDir- DUL- Link Control 0: CFlE+ CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0 IsocEn- LSEn+ ExtCTL- 64b- Link Config 0: MLWI=16bit DwFcIn- MLWO=16bit DwFcOut- LWI=16bit DwFcInEn- LWO=16bit DwFcOutEn- Link Control 1: CFlE- CST- CFE- <LkFail+ Init- EOC+ TXO+ <CRCErr=0 IsocEn- LSEn- ExtCTL- 64b- Link Config 1: MLWI=8bit DwFcIn- MLWO=8bit DwFcOut- LWI=8bit DwFcInEn- LWO=8bit DwFcOutEn- Revision ID: 1.03 Link Frequency 0: 1.0GHz Link Error 0: <Prot- <Ovfl- <EOC- CTLTm- Link Frequency Capability 0: 200MHz+ 300MHz+ 400MHz+ 500MHz+ 600MHz+ 800MHz+ 1.0GHz+ 1.2GHz- 1.4GHz- 1.6GHz- Vend- Feature Capability: IsocFC+ LDTSTOP+ CRCTM- ECTLT- 64bA- UIDRD- Link Frequency 1: 200MHz Link Error 1: <Prot- <Ovfl- <EOC- CTLTm- Link Frequency Capability 1: 200MHz- 300MHz- 400MHz- 500MHz- 600MHz- 800MHz- 1.0GHz- 1.2GHz- 1.4GHz- 1.6GHz- Vend- Error Handling: PFlE+ OFlE+ PFE- OFE- EOCFE- RFE- CRCFE- SERRFE- CF- RE- PNFE- ONFE- EOCNFE- RNFE- CRCNFE- SERRNFE- Prefetchable memory behind bridge Upper: 00-00 Bus Number: 00 Capabilities: [e0] #00 [fee0] 00:01.0 ISA bridge: nVidia Corporation MCP55 LPC Bridge (rev a2) Subsystem: ASUSTeK Computer Inc. Unknown device 8239 Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 00:01.1 SMBus: nVidia Corporation MCP55 SMBus (rev a2) Subsystem: ASUSTeK Computer Inc. Unknown device 8239 Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Interrupt: pin A routed to IRQ 255 Region 0: I/O ports at fc00 [size=64] Region 4: I/O ports at 1c00 [size=64] Region 5: I/O ports at 1c40 [size=64] Capabilities: [44] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00:01.2 RAM memory: nVidia Corporation MCP55 Memory Controller (rev a2) Subsystem: ASUSTeK Computer Inc. Unknown device 8239 Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- 00:02.0 USB Controller: nVidia Corporation MCP55 USB Controller (rev a1) (prog-if 10 [OHCI]) Subsystem: ASUSTeK Computer Inc. Unknown device 8239 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 (750ns min, 250ns max) Interrupt: pin A routed to IRQ 20 Region 0: Memory at fe02f000 (32-bit, non-prefetchable) [size=4K] Capabilities: [44] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00:02.1 USB Controller: nVidia Corporation MCP55 USB Controller (rev a2) (prog-if 20 [EHCI]) Subsystem: ASUSTeK Computer Inc. Unknown device 8239 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 (750ns min, 250ns max) Interrupt: pin B routed to IRQ 23 Region 0: Memory at fe02e000 (32-bit, non-prefetchable) [size=256] Capabilities: [44] Debug port Capabilities: [80] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00:04.0 IDE interface: nVidia Corporation MCP55 IDE (rev a1) (prog-if 8a [Master SecP PriP]) Subsystem: Unknown device f043:8239 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 (750ns min, 250ns max) Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable) [disabled] [size=8] Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable) [disabled] [size=1] Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable) [disabled] [size=8] Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable) [disabled] [size=1] Region 4: I/O ports at f000 [size=16] Capabilities: [44] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00:05.0 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a2) (prog-if 85 [Master SecO PriO]) Subsystem: ASUSTeK Computer Inc. Unknown device 8239 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 (750ns min, 250ns max) Interrupt: pin A routed to IRQ 23 Region 0: I/O ports at 09f0 [size=8] Region 1: I/O ports at 0bf0 [size=4] Region 2: I/O ports at 0970 [size=8] Region 3: I/O ports at 0b70 [size=4] Region 4: I/O ports at dc00 [size=16] Region 5: Memory at fe02d000 (32-bit, non-prefetchable) [size=4K] Capabilities: [44] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [b0] Message Signalled Interrupts: 64bit+ Queue=0/2 Enable- Address: 0000000000000000 Data: 0000 Capabilities: [cc] HyperTransport: MSI Mapping 00:05.1 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a2) (prog-if 85 [Master SecO PriO]) Subsystem: ASUSTeK Computer Inc. Unknown device 8239 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 (750ns min, 250ns max) Interrupt: pin B routed to IRQ 22 Region 0: I/O ports at 09e0 [size=8] Region 1: I/O ports at 0be0 [size=4] Region 2: I/O ports at 0960 [size=8] Region 3: I/O ports at 0b60 [size=4] Region 4: I/O ports at c800 [size=16] Region 5: Memory at fe02c000 (32-bit, non-prefetchable) [size=4K] Capabilities: [44] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [b0] Message Signalled Interrupts: 64bit+ Queue=0/2 Enable- Address: 0000000000000000 Data: 0000 Capabilities: [cc] HyperTransport: MSI Mapping 00:05.2 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a2) (prog-if 85 [Master SecO PriO]) Subsystem: ASUSTeK Computer Inc. Unknown device 8239 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 (750ns min, 250ns max) Interrupt: pin C routed to IRQ 21 Region 0: I/O ports at c400 [size=8] Region 1: I/O ports at c000 [size=4] Region 2: I/O ports at bc00 [size=8] Region 3: I/O ports at b800 [size=4] Region 4: I/O ports at b400 [size=16] Region 5: Memory at fe02b000 (32-bit, non-prefetchable) [size=4K] Capabilities: [44] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [b0] Message Signalled Interrupts: 64bit+ Queue=0/2 Enable- Address: 0000000000000000 Data: 0000 Capabilities: [cc] HyperTransport: MSI Mapping 00:06.0 PCI bridge: nVidia Corporation Unknown device 0370 (rev a2) (prog-if 01 [Subtractive decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Bus: primary=00, secondary=01, subordinate=01, sec-latency=32 I/O behind bridge: 0000a000-0000afff Memory behind bridge: fc000000-fcffffff Prefetchable memory behind bridge: fff00000-000fffff Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B- Capabilities: [b8] #0d [0000] Capabilities: [8c] HyperTransport: MSI Mapping 00:06.1 Audio device: nVidia Corporation MCP55 High Definition Audio (rev a2) Subsystem: ASUSTeK Computer Inc. Unknown device 81f6 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 (500ns min, 1250ns max) Interrupt: pin B routed to IRQ 22 Region 0: Memory at fe024000 (32-bit, non-prefetchable) [size=16K] Capabilities: [44] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [50] Message Signalled Interrupts: 64bit+ Queue=0/0 Enable- Address: 0000000000000000 Data: 0000 Capabilities: [6c] HyperTransport: MSI Mapping 00:0a.0 PCI bridge: nVidia Corporation Unknown device 0376 (rev a2) (prog-if 00 [Normal decode]) Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0, Cache Line Size: 32 bytes Bus: primary=00, secondary=02, subordinate=02, sec-latency=0 I/O behind bridge: 0000f000-00000fff Memory behind bridge: fff00000-000fffff Prefetchable memory behind bridge: 00000000fff00000-0000000000000000 Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B- Capabilities: [40] #0d [0000] Capabilities: [48] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [50] Message Signalled Interrupts: 64bit+ Queue=0/1 Enable- Address: 0000000000000000 Data: 0000 Capabilities: [60] HyperTransport: MSI Mapping Capabilities: [80] Express Root Port (Slot+) IRQ 0 Device: Supported: MaxPayload 256 bytes, PhantFunc 0, ExtTag- Device: Latency L0s <512ns, L1 <4us Device: Errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+ Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+ Device: MaxPayload 256 bytes, MaxReadReq 512 bytes Link: Supported Speed 2.5Gb/s, Width x8, ASPM L0s L1, Port 5 Link: Latency L0s <512ns, L1 <4us Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch- Link: Speed 2.5Gb/s, Width x8 Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug- Surpise- Slot: Number 0, PowerLimit 0.000000 Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- Slot: AttnInd Off, PwrInd On, Power- Root: Correctable- Non-Fatal- Fatal- PME- Capabilities: [100] Virtual Channel 00:0b.0 PCI bridge: nVidia Corporation Unknown device 0374 (rev a2) (prog-if 00 [Normal decode]) Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0, Cache Line Size: 32 bytes Bus: primary=00, secondary=03, subordinate=03, sec-latency=0 I/O behind bridge: 0000f000-00000fff Memory behind bridge: fff00000-000fffff Prefetchable memory behind bridge: 00000000fff00000-0000000000000000 Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B- Capabilities: [40] #0d [0000] Capabilities: [48] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [50] Message Signalled Interrupts: 64bit+ Queue=0/1 Enable- Address: 0000000000000000 Data: 0000 Capabilities: [60] HyperTransport: MSI Mapping Capabilities: [80] Express Root Port (Slot+) IRQ 0 Device: Supported: MaxPayload 256 bytes, PhantFunc 0, ExtTag- Device: Latency L0s <512ns, L1 <4us Device: Errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+ Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+ Device: MaxPayload 256 bytes, MaxReadReq 512 bytes Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 4 Link: Latency L0s <512ns, L1 <4us Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch- Link: Speed 2.5Gb/s, Width x4 Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug- Surpise- Slot: Number 0, PowerLimit 0.000000 Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- Slot: AttnInd Off, PwrInd On, Power- Root: Correctable- Non-Fatal- Fatal- PME- Capabilities: [100] Virtual Channel 00:0c.0 PCI bridge: nVidia Corporation Unknown device 0374 (rev a2) (prog-if 00 [Normal decode]) Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0, Cache Line Size: 32 bytes Bus: primary=00, secondary=04, subordinate=04, sec-latency=0 I/O behind bridge: 0000f000-00000fff Memory behind bridge: fff00000-000fffff Prefetchable memory behind bridge: 00000000fff00000-0000000000000000 Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B- Capabilities: [40] #0d [0000] Capabilities: [48] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [50] Message Signalled Interrupts: 64bit+ Queue=0/1 Enable- Address: 0000000000000000 Data: 0000 Capabilities: [60] HyperTransport: MSI Mapping Capabilities: [80] Express Root Port (Slot+) IRQ 0 Device: Supported: MaxPayload 256 bytes, PhantFunc 0, ExtTag- Device: Latency L0s <512ns, L1 <4us Device: Errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+ Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+ Device: MaxPayload 256 bytes, MaxReadReq 512 bytes Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 3 Link: Latency L0s <512ns, L1 <4us Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch- Link: Speed 2.5Gb/s, Width x4 Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug- Surpise- Slot: Number 0, PowerLimit 0.000000 Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- Slot: AttnInd Off, PwrInd On, Power- Root: Correctable- Non-Fatal- Fatal- PME- Capabilities: [100] Virtual Channel 00:0d.0 PCI bridge: nVidia Corporation Unknown device 0378 (rev a2) (prog-if 00 [Normal decode]) Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0, Cache Line Size: 32 bytes Bus: primary=00, secondary=05, subordinate=05, sec-latency=0 I/O behind bridge: 0000f000-00000fff Memory behind bridge: fff00000-000fffff Prefetchable memory behind bridge: 00000000fff00000-0000000000000000 Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B- Capabilities: [40] #0d [0000] Capabilities: [48] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [50] Message Signalled Interrupts: 64bit+ Queue=0/1 Enable- Address: 0000000000000000 Data: 0000 Capabilities: [60] HyperTransport: MSI Mapping Capabilities: [80] Express Root Port (Slot+) IRQ 0 Device: Supported: MaxPayload 256 bytes, PhantFunc 0, ExtTag- Device: Latency L0s <512ns, L1 <4us Device: Errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+ Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+ Device: MaxPayload 256 bytes, MaxReadReq 512 bytes Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 2 Link: Latency L0s <512ns, L1 <4us Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch- Link: Speed 2.5Gb/s, Width x4 Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug- Surpise- Slot: Number 0, PowerLimit 0.000000 Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- Slot: AttnInd Off, PwrInd On, Power- Root: Correctable- Non-Fatal- Fatal- PME- Capabilities: [100] Virtual Channel 00:0e.0 PCI bridge: nVidia Corporation Unknown device 0375 (rev a2) (prog-if 00 [Normal decode]) Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0, Cache Line Size: 32 bytes Bus: primary=00, secondary=06, subordinate=06, sec-latency=0 I/O behind bridge: 0000f000-00000fff Memory behind bridge: fff00000-000fffff Prefetchable memory behind bridge: 00000000fff00000-0000000000000000 Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B- Capabilities: [40] #0d [0000] Capabilities: [48] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [50] Message Signalled Interrupts: 64bit+ Queue=0/1 Enable- Address: 0000000000000000 Data: 0000 Capabilities: [60] HyperTransport: MSI Mapping Capabilities: [80] Express Root Port (Slot+) IRQ 0 Device: Supported: MaxPayload 256 bytes, PhantFunc 0, ExtTag- Device: Latency L0s <512ns, L1 <4us Device: Errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+ Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+ Device: MaxPayload 256 bytes, MaxReadReq 512 bytes Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 1 Link: Latency L0s <512ns, L1 <4us Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch- Link: Speed 2.5Gb/s, Width x8 Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug- Surpise- Slot: Number 0, PowerLimit 0.000000 Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- Slot: AttnInd Off, PwrInd On, Power- Root: Correctable- Non-Fatal- Fatal- PME- Capabilities: [100] Virtual Channel 00:0f.0 PCI bridge: nVidia Corporation Unknown device 0377 (rev a2) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0, Cache Line Size: 32 bytes Bus: primary=00, secondary=07, subordinate=07, sec-latency=0 I/O behind bridge: 00009000-00009fff Memory behind bridge: f9000000-fbffffff Prefetchable memory behind bridge: 00000000e0000000-00000000eff00000 Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B- Capabilities: [40] #0d [0000] Capabilities: [48] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [50] Message Signalled Interrupts: 64bit+ Queue=0/1 Enable- Address: 0000000000000000 Data: 0000 Capabilities: [60] HyperTransport: MSI Mapping Capabilities: [80] Express Root Port (Slot+) IRQ 0 Device: Supported: MaxPayload 256 bytes, PhantFunc 0, ExtTag- Device: Latency L0s <512ns, L1 <4us Device: Errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+ Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+ Device: MaxPayload 128 bytes, MaxReadReq 512 bytes Link: Supported Speed 2.5Gb/s, Width x16, ASPM L0s L1, Port 0 Link: Latency L0s <512ns, L1 <4us Link: ASPM Disabled RCB 64 bytes CommClk+ ExtSynch- Link: Speed 2.5Gb/s, Width x16 Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug- Surpise- Slot: Number 0, PowerLimit 0.000000 Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- Slot: AttnInd Off, PwrInd On, Power- Root: Correctable- Non-Fatal- Fatal- PME- Capabilities: [100] Virtual Channel 00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Capabilities: [80] HyperTransport: Host or Secondary Interface !!! Possibly incomplete decoding Command: WarmRst+ DblEnd- Link Control: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0 Link Config: MLWI=16bit MLWO=16bit LWI=16bit LWO=16bit Revision ID: 1.02 00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- 00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- 00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Capabilities: [f0] #0f [0010] 01:07.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8029(AS) Subsystem: Realtek Semiconductor Co., Ltd. RTL-8029(AS) Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Interrupt: pin A routed to IRQ 17 Region 0: I/O ports at ac00 [size=32] 01:08.0 Multimedia video controller: Conexant CX23880/1/2/3 PCI Video and Audio Decoder (rev 05) Subsystem: Conexant Unknown device ea3d Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32 (5000ns min, 13750ns max), Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 255 Region 0: Memory at fc000000 (32-bit, non-prefetchable) [size=16M] Capabilities: [44] Vital Product Data Capabilities: [4c] Power Management version 2 Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 07:00.0 VGA compatible controller: nVidia Corporation G70 [GeForce 7600 GT] (rev a1) (prog-if 00 [VGA]) Subsystem: XFX Pine Group Inc. Unknown device 2220 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Interrupt: pin A routed to IRQ 16 Region 0: Memory at f9000000 (32-bit, non-prefetchable) [size=16M] Region 1: Memory at e0000000 (64-bit, prefetchable) [size=256M] Region 3: Memory at fa000000 (64-bit, non-prefetchable) [size=16M] Region 5: I/O ports at 9c00 [size=128] [virtual] Expansion ROM at fbfe0000 [disabled] [size=128K] Capabilities: [60] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [68] Message Signalled Interrupts: 64bit+ Queue=0/0 Enable- Address: 0000000000000000 Data: 0000 Capabilities: [78] Express Endpoint IRQ 0 Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag- Device: Latency L0s <256ns, L1 <4us Device: AtnBtn- AtnInd- PwrInd- Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported- Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+ Device: MaxPayload 128 bytes, MaxReadReq 512 bytes Link: Supported Speed 2.5Gb/s, Width x16, ASPM L0s L1, Port 0 Link: Latency L0s <256ns, L1 <4us Link: ASPM Disabled RCB 128 bytes CommClk+ ExtSynch- Link: Speed 2.5Gb/s, Width x16 Capabilities: [100] Virtual Channel Capabilities: [128] Power Budgeting If you need more info, just ask. Thanks. -- http://u-br.net Linux 2.6.20: Homicidal Dwarf Hamster gcc (GCC) 4.1.2 - To unsubscribe from this list: send the line "unsubscribe linux-net" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
