Hello list,
I am having some problems with the installation of 802.11b orinoco_pci
networking. I have an HP-Compaq nx9110 with a whole lot of cool stuff,
including built-in WiFi. After reading on linux-laptops.org about the nx9010
working great with linux, I thought that there would be no problem. But
there is.
lsmod shows that orinoco_pci and orinoco are loaded. /etc/modules.conf has
"alias eth1 orinoco_pci". /etc/sysconfig/networking-scripts/ifcfg-wireless
has the following:
DEVICE=eth1
BOOTPROTO=dhcp
BROADCAST=255
ONBOOT=yes
MII_NOT_SUPPORTED=yes
Now I cannot bring up eth1 no matter what I try. ifconfig doesn't work, and
I am trying the ifcfg-wireless script with Mandrake 1 and that doesn't work
either. I am having to use Windows to write this Email, so my memory is
slightly shaky on the keywords, but it gives an error message stating that
"off" and "auto" aren't recognised keywords, but they are, dammit. The
keywords refer to the KEY and ESSID options which I confired were right from
the manpage.
Does anyone have any ideas?
dmesg shows the following, posted last so you don't have to read to the end
if you're bored.
5
ACPI: FADT (v001 HP Chinook 0x06040000 ATI 0x000f4240) @ 0x1bf7ce7d
ACPI: SSDT (v001 PTLTD ACPIPST1 0x06040000 LTP 0x00000001) @ 0x1bf7cef1
ACPI: MADT (v001 PTLTD APIC 0x06040000 LTP 0x00000000) @
0x1bf7cfa6
ACPI: DSDT (v001 HP SB200 0x06040000 INTL 0x20030509) @ 0x00000000
ACPI: PM-Timer IO Port: 0x8008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 15:2 APIC version 20
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
Using ACPI for processor (LAPIC) configuration information
Intel MultiProcessor Specification v1.4
Virtual Wire compatibility mode.
OEM ID: Product ID: RS300 Board APIC at: 0xFEE00000
I/O APIC #1 Version 17 at 0xFEC00000.
Enabling APIC mode: Flat. Using 1 I/O APICs
Processors: 1
Built 1 zonelists
Kernel command line: auto BOOT_IMAGE=linux ro root=302 devfs=mount acpi=ht
resume=/dev/hda3 splash=silent
bootsplash: silent mode.
Initializing CPU#0
PID hash table entries: 2048 (order 11: 16384 bytes)
Detected 3067.783 MHz processor.
Using pmtmr for high-res timesource
Console: colour dummy device 80x25
Memory: 449448k/458176k available (1815k kernel code, 7956k reserved, 846k
data, 272k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay loop... 6094.84 BogoMIPS
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
checking if image is initramfs...it isn't (no cpio magic); looks like an
initrd
Freeing initrd memory: 131k freed
CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000
CPU: After vendor identify, caps: bfebfbff 00000000 00000000 00000000
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: After all inits, caps: bfebfbff 00000000 00000000 00000080
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU#0: Intel P4/Xeon Extended MCE MSRs (12) available
CPU#0: Thermal monitoring enabled
CPU: Intel Mobile Intel(R) Pentium(R) 4 CPU 3.06GHz stepping 09
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
ENABLING IO-APIC IRQs
Setting 1 in the phys_id_present_map
...changing IO-APIC physical APIC ID to 1 ... ok.
init IO_APIC IRQs
IO-APIC (apicid-pin) 1-0, 1-5, 1-10, 1-11, 1-20, 1-21, 1-22, 1-23 not
connected.
..TIMER: vector=0x31 pin1=2 pin2=0
number of MP IRQ sources: 24.
number of IO-APIC #1 registers: 24.
testing the IO APIC.......................
IO APIC #1......
.... register #00: 01000000
....... : physical APIC id: 01
....... : Delivery Type: 0
....... : LTS : 0
.... register #01: 00170011
....... : max redirection entries: 0017
....... : PRQ implemented: 0
....... : IO APIC version: 0011
.... register #02: 01000000
....... : arbitration: 01
.... IRQ redirection table:
NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
00 000 00 1 0 0 0 0 0 0 00
01 001 01 0 0 0 0 0 1 1 39
02 001 01 0 0 0 0 0 1 1 31
03 001 01 0 0 0 0 0 1 1 41
04 001 01 0 0 0 0 0 1 1 49
05 000 00 1 0 0 0 0 0 0 00
06 001 01 0 0 0 0 0 1 1 51
07 001 01 0 0 0 0 0 1 1 59
08 001 01 0 0 0 0 0 1 1 61
09 001 01 0 0 0 0 0 1 1 69
0a 000 00 1 0 0 0 0 0 0 00
0b 000 00 1 0 0 0 0 0 0 00
0c 001 01 0 0 0 0 0 1 1 71
0d 001 01 0 0 0 0 0 1 1 79
0e 001 01 0 0 0 0 0 1 1 81
0f 001 01 0 0 0 0 0 1 1 89
10 001 01 1 1 0 1 0 1 1 91
11 001 01 1 1 0 1 0 1 1 99
12 001 01 1 1 0 1 0 1 1 A1
13 001 01 1 1 0 1 0 1 1 A9
14 000 00 1 0 0 0 0 0 0 00
15 000 00 1 0 0 0 0 0 0 00
16 000 00 1 0 0 0 0 0 0 00
17 000 00 1 0 0 0 0 0 0 00
IRQ to pin mappings:
IRQ0 -> 0:2
IRQ1 -> 0:1
IRQ3 -> 0:3
IRQ4 -> 0:4
IRQ6 -> 0:6
IRQ7 -> 0:7
IRQ8 -> 0:8
IRQ9 -> 0:9
IRQ12 -> 0:12
IRQ13 -> 0:13
IRQ14 -> 0:14
IRQ15 -> 0:15
IRQ16 -> 0:16
IRQ17 -> 0:17
IRQ18 -> 0:18
IRQ19 -> 0:19
.................................... done.
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 3066.0222 MHz.
..... host bus clock speed is 133.0313 MHz.
NET: Registered protocol family 16
EISA bus registered
PCI: PCI BIOS revision 2.10 entry at 0xfd968, last bus=2
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20040211
ACPI: Interpreter disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
PnPBIOS: Disabled
PCI: Probing PCI hardware
PCI: Probing PCI hardware (bus 00)
PCI: Ignoring BAR0-3 of IDE controller 0000:00:14.1
Transparent bridge - 0000:00:14.4
PCI: Using IRQ router default [1002/434c] at 0000:00:14.3
PCI->APIC IRQ transform: (B0,I19,P0) -> 19
PCI->APIC IRQ transform: (B0,I19,P0) -> 19
PCI->APIC IRQ transform: (B0,I20,P0) -> 17
PCI->APIC IRQ transform: (B0,I20,P1) -> 17
PCI->APIC IRQ transform: (B0,I20,P1) -> 17
PCI->APIC IRQ transform: (B1,I5,P0) -> 16
PCI->APIC IRQ transform: (B2,I0,P0) -> 16
PCI->APIC IRQ transform: (B2,I2,P0) -> 18
PCI->APIC IRQ transform: (B2,I3,P0) -> 19
PCI: using PPB(B0,I20,P0) to get irq 17
PCI->APIC IRQ transform: (B2,I4,P0) -> 17
PCI: using PPB(B0,I20,P1) to get irq 17
PCI->APIC IRQ transform: (B2,I4,P1) -> 17
PCI->APIC IRQ transform: (B2,I7,P0) -> 16
PCI->APIC IRQ transform: (B2,I7,P1) -> 18
PCI->APIC IRQ transform: (B2,I7,P2) -> 19
vesafb: framebuffer at 0xf0000000, mapped to 0xdc800000, size 16384k
vesafb: mode is 800x600x16, linelength=1600, pages=67
vesafb: protected mode interface info at c000:5259
vesafb: scrolling: redraw
vesafb: directcolor: size=0:5:6:5, shift=0:11:5:0
fb0: VESA VGA frame buffer device
apm: BIOS not found.
ikconfig 0.7 with /proc/config*
VFS: Disk quotas dquot_6.5.1
devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
Initializing Cryptographic API
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
bootsplash 3.1.3-2003/11/14: looking for picture.... silentjpeg size 14856
bytes, found (800x600, 14808 bytes, v3).
Console: switching to colour frame buffer device 92x32
pty: 1024 Unix98 ptys configured
Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing enabled
RAMDISK driver initialized: 16 RAM disks of 32000K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ATIIXP: IDE controller at PCI slot 0000:00:14.1
ATIIXP: chipset revision 0
ATIIXP: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0x8060-0x8067, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0x8068-0x806f, BIOS settings: hdc:DMA, hdd:pio
hda: HITACHI_DK23FA-40, ATA DISK drive
Using anticipatory io scheduler
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hdc: SD-R2512, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 128KiB
hda: 78140160 sectors (40007 MB) w/2048KiB Cache, CHS=65535/16/63, UDMA(100)
/dev/ide/host0/bus0/target0/lun0: p1 p2 p3 p4
Console: switching to colour frame buffer device 92x32
mice: PS/2 mouse device common for all mice
i8042.c: Detected active multiplexing controller, rev 1.9.
serio: i8042 AUX0 port at 0x60,0x64 irq 12
serio: i8042 AUX1 port at 0x60,0x64 irq 12
serio: i8042 AUX2 port at 0x60,0x64 irq 12
serio: i8042 AUX3 port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
input: AT Translated Set 2 keyboard on isa0060/serio0
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
EISA: Probing bus 0 at eisa0
NET: Registered protocol family 2
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 65536)
NET: Registered protocol family 1
BIOS EDD facility v0.12 2004-Jan-26, 1 devices found
Please report your BIOS at http://linux.dell.com/edd/results.html
Resume Machine: resuming from /dev/hda3
Resuming from device hda3
Resume Machine: This is normal swap space
PM: Reading pmdisk image.
PM: Resume from disk failed.
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
RAMDISK: Compressed image found at block 0
VFS: Mounted root (ext2 filesystem).
Mounted devfs on /dev
EXT3-fs: INFO: recovery required on readonly filesystem.
EXT3-fs: write access will be enabled during recovery.
kjournald starting. Commit interval 5 seconds
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
Mounted devfs on /dev
Freeing unused kernel memory: 272k freed
Real Time Clock Driver v1.12
drivers/usb/core/usb.c: registered new driver usbfs
drivers/usb/core/usb.c: registered new driver hub
ohci_hcd: 2004 Feb 02 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ohci_hcd: block sizes: ed 64 td 64
ohci_hcd 0000:00:13.0: OHCI Host Controller
ohci_hcd 0000:00:13.0: irq 19, pci mem dd92b000
ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 1
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 3 ports detected
ohci_hcd 0000:00:13.1: OHCI Host Controller
ohci_hcd 0000:00:13.1: irq 19, pci mem dd92d000
ohci_hcd 0000:00:13.1: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 3 ports detected
ohci_hcd 0000:02:07.0: OHCI Host Controller
ohci_hcd 0000:02:07.0: irq 16, pci mem dd934000
ohci_hcd 0000:02:07.0: new USB bus registered, assigned bus number 3
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 3 ports detected
ohci_hcd 0000:02:07.1: OHCI Host Controller
ohci_hcd 0000:02:07.1: irq 18, pci mem dd936000
ohci_hcd 0000:02:07.1: new USB bus registered, assigned bus number 4
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
usb 3-2: new low speed USB device using address 2
ehci_hcd 0000:02:07.2: EHCI Host Controller
ehci_hcd 0000:02:07.2: irq 19, pci mem dd938c00
ehci_hcd 0000:02:07.2: new USB bus registered, assigned bus number 5
ehci_hcd 0000:02:07.2: USB 2.0 enabled, EHCI 1.00, driver 2003-Dec-29
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 5 ports detected
bootsplash: status on console 0 changed to on
usb 3-2: device not accepting address 2, error -110
usb 4-1: new low speed USB device using address 2
drivers/usb/core/usb.c: registered new driver hiddev
drivers/usb/input/hid-ff.c: hid_ff_init could not find initializer
input: USB HID v1.00 Keyboard [USBPS2] on usb-0000:02:07.1-1
drivers/usb/input/hid-ff.c: hid_ff_init could not find initializer
input: USB HID v1.00 Mouse [USBPS2] on usb-0000:02:07.1-1
drivers/usb/core/usb.c: registered new driver hid
drivers/usb/input/hid-core.c: v2.0:USB HID core driver
drivers/usb/core/usb.c: registered new driver usbkbd
drivers/usb/input/usbkbd.c: :USB HID Boot Protocol keyboard driver
drivers/usb/core/usb.c: registered new driver usbmouse
drivers/usb/input/usbmouse.c: v1.6:USB HID Boot Protocol mouse driver
usb 4-2: new full speed USB device using address 3
Bluetooth: Core ver 2.3
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: HCI USB driver ver 2.4
drivers/usb/core/usb.c: registered new driver hci_usb
usb 3-2: new low speed USB device using address 3
drivers/usb/input/hid-ff.c: hid_ff_init could not find initializer
input: USB HID v1.00 Mouse [Microsoft Microsoft IntelliMouseR Optical] on
usb-0000:02:07.0-2
ts: Compaq touchscreen protocol output
EXT3 FS on hda2, internal journal
Adding 818992k swap on /dev/hda3. Priority:-1 extents:1
SCSI subsystem initialized
imm: Version 2.05 (for Linux 2.4.0)
parport0: PC-style at 0x378 [PCSPP,EPP]
parport0: cpp_daisy: aa5500ff(38)
parport0: assign_addrs: aa5500ff(38)
parport0: cpp_daisy: aa5500ff(38)
parport0: assign_addrs: aa5500ff(38)
ppa: Version 2.07 (for Linux 2.4.x)
Linux agpgart interface v0.100 (c) Dave Jones
agpgart: Detected Ati IGP9100/M chipset
agpgart: Maximum main memory to use for agp memory: 380M
agpgart: AGP aperture is 32M @ 0xea000000
Supermount version 2.0.4 for kernel 2.6
NTFS driver 2.1.6 [Flags: R/O MODULE].
NTFS volume version 3.1.
ohci1394: $Rev: 1097 $ Ben Collins <bcollins@debian.org>
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[16] MMIO=[e8208000-e82087ff]
Max Packet=[2048]
ieee1394: Host added: ID:BUS[0-00:1023] GUID[413f02001e2d013d]
8139too Fast Ethernet driver 0.9.27
eth0: RealTek RTL8139 at 0xdda47800, 00:02:3f:6c:b4:d5, IRQ 19
eth0: Identified 8139 chip type 'RTL-8101'
orinoco.c 0.13e (David Gibson <hermes@gibson.dropbear.id.au> and others)
orinoco_pci.c 0.13e (David Gibson <hermes@gibson.dropbear.id.au> & Jean
Tourrilhes <jt@hpl.hp.com>)
ip_tables: (C) 2000-2002 Netfilter core team
ip_conntrack version 2.1 (3579 buckets, 28632 max) - 300 bytes per conntrack
ip_tables: (C) 2000-2002 Netfilter core team
ip_conntrack version 2.1 (3579 buckets, 28632 max) - 300 bytes per conntrack
Linux Kernel Card Services
options: [pci] [cardbus] [pm]
Yenta: CardBus bridge found at 0000:02:04.0 [103c:006b]
Yenta: ISA IRQ mask 0x0298, PCI irq 17
Socket status: 30000006
Yenta: CardBus bridge found at 0000:02:04.1 [103c:006b]
Yenta: ISA IRQ mask 0x0298, PCI irq 17
Socket status: 30000006
cs: IO port probe 0x0c00-0x0cff: excluding 0xc00-0xc07 0xc10-0xc17
0xc50-0xc57 0xc68-0xc6f 0xcd0-0xcd7
cs: IO port probe 0x0100-0x04ff: excluding 0x200-0x20f 0x408-0x40f
0x4d0-0x4d7
cs: IO port probe 0x0a00-0x0aff: clean.
inserting floppy driver for 2.6.3-4mdk
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
hdc: ATAPI 24X DVD-ROM CD-R/RW drive, 2048kB Cache, DMA
Uniform CD-ROM driver Revision: 3.20
ide-floppy driver 0.99.newide
NET: Registered protocol family 17
eth0: link down
NET: Registered protocol family 10
Disabled Privacy Extensions on device c035fa20(lo)
IPv6 over IPv4 tunneling driver
mtrr: 0xf0000000,0x4000000 overlaps existing 0xf0000000,0x1000000
atkbd.c: Unknown key released (translated set 2, code 0x7a on
isa0060/serio0).
atkbd.c: This is an XFree86 bug. It shouldn't access hardware directly.
atkbd.c: Unknown key released (translated set 2, code 0x7a on
isa0060/serio0).
atkbd.c: This is an XFree86 bug. It shouldn't access hardware directly.
bootsplash 3.1.3-2003/11/14: looking for picture.... found (800x600, 11943
bytes, v3).
bootsplash: status on console 0 changed to on
bootsplash 3.1.3-2003/11/14: looking for picture.... found (800x600, 11943
bytes, v3).
bootsplash: status on console 1 changed to on
bootsplash 3.1.3-2003/11/14: looking for picture.... found (800x600, 11943
bytes, v3).
bootsplash: status on console 2 changed to on
bootsplash 3.1.3-2003/11/14: looking for picture.... found (800x600, 11943
bytes, v3).
bootsplash: status on console 3 changed to on
bootsplash 3.1.3-2003/11/14: looking for picture.... found (800x600, 11943
bytes, v3).
bootsplash: status on console 4 changed to on
bootsplash 3.1.3-2003/11/14: looking for picture.... found (800x600, 11943
bytes, v3).
bootsplash: status on console 5 changed to on
eth0: no IPv6 routers present
-
: send the line "unsubscribe linux-net" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
