Hi,
Had an issue today with 2.6.4-rc2 and a pcmcia 3c59x card on my laptop.
Suddenly it stopped working, I tried rmmoding and reloading the driver,
but no success.
Rebooting the kernel made it work again.
If you need more information, just ask.
spurious 8259A interrupt: IRQ7.
eth0: command 0x5800 did not complete! Status=0xffff
eth0: command 0x2804 did not complete! Status=0xffff
eth0: command 0x3002 did not complete! Status=0xffff
eth0: command 0x3002 did not complete! Status=0xffff
eth0: command 0x3002 did not complete! Status=0xffff
eth0: command 0x3002 did not complete! Status=0xffff
eth0: command 0x3002 did not complete! Status=0xffff
eth0: command 0x3002 did not complete! Status=0xffff
eth0: command 0x3002 did not complete! Status=0xffff
eth0: command 0x3002 did not complete! Status=0xffff
eth0: command 0x3002 did not complete! Status=0xffff
eth0: command 0x3002 did not complete! Status=0xffff
eth0: command 0x3002 did not complete! Status=0xffff
eth0: command 0x3002 did not complete! Status=0xffff
eth0: command 0x3002 did not complete! Status=0xffff
eth0: command 0x5800 did not complete! Status=0xffff
eth0: command 0x2804 did not complete! Status=0xffff
eth0: command 0x3002 did not complete! Status=0xffff
eth0: command 0x3002 did not complete! Status=0xffff
eth0: command 0x3002 did not complete! Status=0xffff
PCI: Enabling device 0000:02:00.0 (0000 -> 0003)
3c59x: Donald Becker and others. www.scyld.com/network/vortex.html
0000:02:00.0: 3Com PCI 3CCFE575CT Tornado CardBus at 0x4000. Vers LK1.1.19
PCI: Setting latency timer of device 0000:02:00.0 to 64
***WARNING*** No MII transceivers found!
divert: allocating divert_blk for eth0
eth0: command 0x5800 did not complete! Status=0xffff
eth0: command 0x2804 did not complete! Status=0xffff
Complete dmesg:
Linux version 2.6.4-rc2 (marcelo@dmt.cyclades) (gcc version 3.2.2 20030222 (Red Hat Linux 3.2.2-5)) #1 Mon Mar 8 14:30:17 BRT 2004
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000000b7f0000 (usable)
BIOS-e820: 000000000b7f0000 - 000000000b7f8000 (ACPI data)
BIOS-e820: 000000000b7f8000 - 000000000b800000 (ACPI NVS)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
183MB LOWMEM available.
On node 0 totalpages: 47088
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 42992 pages, LIFO batch:10
HighMem zone: 0 pages, LIFO batch:1
DMI 2.0 present.
ACPI disabled because your bios is from 2000 and too old
You can enable it with acpi=force
Built 1 zonelists
Kernel command line: ro root=/dev/hda3
Local APIC disabled by BIOS -- reenabling.
Could not enable APIC!
Initializing CPU#0
PID hash table entries: 1024 (order 10: 8192 bytes)
Detected 647.966 MHz processor.
Using tsc for high-res timesource
Console: colour VGA+ 80x25
Memory: 182844k/188352k available (1848k kernel code, 4860k reserved, 721k data, 236k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay loop... 1273.85 BogoMIPS
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: After generic identify, caps: 0387f9ff 00000000 00000000 00000000
CPU: After vendor identify, caps: 0387f9ff 00000000 00000000 00000000
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 256K
CPU serial number disabled.
CPU: After all inits, caps: 0383f9ff 00000000 00000000 00000040
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: Intel Pentium III (Coppermine) stepping 03
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
NET: Registered protocol family 16
EISA bus registered
PCI: PCI BIOS revision 2.10 entry at 0xf0200, last bus=1
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20040211
ACPI: Interpreter disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
ACPI: ACPI tables contain no PCI IRQ routing entries
PCI: Invalid ACPI-PCI IRQ routing table
PCI: Probing PCI hardware
PCI: Probing PCI hardware (bus 00)
SBF: Simple Boot Flag extension found and enabled.
SBF: Setting boot flags 0x1
apm: BIOS version 1.2 Flags 0x0f (Driver version 1.16ac)
VFS: Disk quotas dquot_6.5.1
Activating ISA DMA hang workarounds.
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12
Using anticipatory io scheduler
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
divert: not allocating divert_blk for non-ethernet device lo
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ALI15X3: IDE controller at PCI slot 0000:00:10.0
ALI15X3: chipset revision 195
ALI15X3: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0x7050-0x7057, BIOS settings: hda:DMA, hdb:pio
ALI15X3: simplex device: DMA forced
ide1: BM-DMA at 0x7058-0x705f, BIOS settings: hdc:DMA, hdd:DMA
hda: IBM-DJSA-210, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: max request size: 128KiB
hda: 19640880 sectors (10056 MB) w/384KiB Cache, CHS=19485/16/63, UDMA(33)
hda: hda1 hda2 hda3 hda4 < hda5 >
ide-floppy driver 0.99.newide
mice: PS/2 mouse device common for all mice
serio: i8042 AUX port at 0x60,0x64 irq 12
Synaptics Touchpad, model: 1
Firmware: 4.6
180 degree mounted touchpad
Sensor: 18
new absolute packet format
Touchpad has extended capability bits
-> four buttons
-> multifinger detection
-> palm detection
input: SynPS/2 Synaptics TouchPad on isa0060/serio1
serio: i8042 KBD port at 0x60,0x64 irq 1
input: AT Translated Set 2 keyboard on isa0060/serio0
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
EISA: Probing bus 0 at eisa0
NET: Registered protocol family 2
IP: routing cache hash table of 1024 buckets, 8Kbytes
TCP: Hash tables configured (established 16384 bind 32768)
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 8
NET: Registered protocol family 20
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
EXT3-fs: INFO: recovery required on readonly filesystem.
EXT3-fs: write access will be enabled during recovery.
(fs/jbd/recovery.c, 252): journal_recover: JBD: recovery, exit status 0, recovered transactions 330858 to 331377
(fs/jbd/recovery.c, 254): journal_recover: JBD: Replayed 3689 and revoked 4/5 blocks
kjournald starting. Commit interval 5 seconds
EXT3-fs: hda3: orphan cleanup on readonly fs
ext3_orphan_cleanup: deleting unreferenced inode 687561
ext3_orphan_cleanup: deleting unreferenced inode 687559
EXT3-fs: hda3: 2 orphan inodes deleted
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 236k freed
EXT3 FS on hda3, internal journal
Adding 240932k swap on /dev/hda5. Priority:-1 extents:1
parport0: PC-style at 0x378 [PCSPP,TRISTATE,EPP]
parport0: cpp_daisy: aa5500ff(38)
parport0: assign_addrs: aa5500ff(38)
parport0: cpp_daisy: aa5500ff(38)
parport0: assign_addrs: aa5500ff(38)
ieee1394: Initialized config rom entry `ip1394'
ohci1394: $Rev: 1172 $ Ben Collins <bcollins@debian.org>
PCI: Guessed IRQ 10 for device 0000:00:0b.0
PCI: Sharing IRQ 10 with 0000:00:0a.0
ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[10] MMIO=[82400000-824007ff] Max Packet=[2048]
ieee1394: Host added: ID:BUS[0-00:1023] GUID[000124100c00f669]
Linux Kernel Card Services
options: [pci] [cardbus] [pm]
PCI: Guessed IRQ 11 for device 0000:00:13.0
PCI: Sharing IRQ 11 with 0000:00:13.1
Yenta: CardBus bridge found at 0000:00:13.0 [1025:1014]
Yenta: ISA IRQ mask 0x0238, PCI irq 11
Socket status: 30000820
PCI: Guessed IRQ 11 for device 0000:00:13.1
PCI: Sharing IRQ 11 with 0000:00:13.0
Yenta: CardBus bridge found at 0000:00:13.1 [1025:1014]
Yenta: ISA IRQ mask 0x0238, PCI irq 11
Socket status: 30000410
cs: IO port probe 0x0c00-0x0cff: clean.
cs: IO port probe 0x0100-0x04ff: excluding 0x2f8-0x2ff 0x3c0-0x3df 0x408-0x40f 0x480-0x48f 0x4d0-0x4d7
cs: IO port probe 0x0a00-0x0aff: clean.
cs: memory probe 0xa0000000-0xa0ffffff: clean.
PCI: Enabling device 0000:02:00.0 (0000 -> 0003)
3c59x: Donald Becker and others. www.scyld.com/network/vortex.html
0000:02:00.0: 3Com PCI 3CCFE575CT Tornado CardBus at 0x4000. Vers LK1.1.19
PCI: Setting latency timer of device 0000:02:00.0 to 64
divert: allocating divert_blk for eth0
atkbd.c: Unknown key released (translated set 2, code 0x7a on isa0060/serio0).
atkbd.c: This is an XFree86 bug. It shouldn't access hardware directly.
atkbd.c: Unknown key released (translated set 2, code 0x7a on isa0060/serio0).
atkbd.c: This is an XFree86 bug. It shouldn't access hardware directly.
process `rndc' is using obsolete setsockopt SO_BSDCOMPAT
hda: start_power_step(step: 0)
hda: start_power_step(step: 1)
hda: complete_power_step(step: 1, stat: 50, err: 0)
hda: completing PM request, suspend
PCI: Guessed IRQ 10 for device 0000:00:0b.0
PCI: Sharing IRQ 10 with 0000:00:0a.0
hda: Wakeup request inited, waiting for !BSY...
hda: start_power_step(step: 1000)
blk: queue cb596e00, I/O limit 4095Mb (mask 0xffffffff)
hda: completing PM request, resume
spurious 8259A interrupt: IRQ7.
eth0: command 0x5800 did not complete! Status=0xffff
eth0: command 0x2804 did not complete! Status=0xffff
eth0: command 0x3002 did not complete! Status=0xffff
eth0: command 0x3002 did not complete! Status=0xffff
eth0: command 0x3002 did not complete! Status=0xffff
eth0: command 0x3002 did not complete! Status=0xffff
eth0: command 0x3002 did not complete! Status=0xffff
eth0: command 0x3002 did not complete! Status=0xffff
eth0: command 0x3002 did not complete! Status=0xffff
eth0: command 0x3002 did not complete! Status=0xffff
eth0: command 0x3002 did not complete! Status=0xffff
eth0: command 0x3002 did not complete! Status=0xffff
eth0: command 0x3002 did not complete! Status=0xffff
eth0: command 0x3002 did not complete! Status=0xffff
eth0: command 0x3002 did not complete! Status=0xffff
psmouse.c: TouchPad at isa0060/serio1/input0 lost synchronization, throwing 2 bytes away.
Synaptics driver lost sync at byte 1
eth0: command 0x3002 did not complete! Status=0xffff
Synaptics driver lost sync at byte 1
eth0: command 0x3002 did not complete! Status=0xffff
eth0: command 0x3002 did not complete! Status=0xffff
psmouse.c: TouchPad at isa0060/serio1/input0 lost synchronization, throwing 1 bytes away.
Synaptics driver lost sync at byte 1
Synaptics driver resynced.
eth0: command 0x5800 did not complete! Status=0xffff
eth0: command 0x2804 did not complete! Status=0xffff
eth0: command 0x3002 did not complete! Status=0xffff
eth0: command 0x3002 did not complete! Status=0xffff
eth0: command 0x3002 did not complete! Status=0xffff
divert: freeing divert_blk for eth0
PCI: Enabling device 0000:02:00.0 (0000 -> 0003)
3c59x: Donald Becker and others. www.scyld.com/network/vortex.html
0000:02:00.0: 3Com PCI 3CCFE575CT Tornado CardBus at 0x4000. Vers LK1.1.19
PCI: Setting latency timer of device 0000:02:00.0 to 64
***WARNING*** No MII transceivers found!
divert: allocating divert_blk for eth0
eth0: command 0x5800 did not complete! Status=0xffff
eth0: command 0x2804 did not complete! Status=0xffff
/proc/interrupts:
CPU0
0: 2069058 XT-PIC timer
1: 8145 XT-PIC i8042
2: 0 XT-PIC cascade
8: 2 XT-PIC rtc
10: 3 XT-PIC ohci1394
11: 169 XT-PIC yenta, yenta, eth0
12: 126677 XT-PIC i8042
14: 16203 XT-PIC ide0
NMI: 0
LOC: 0
ERR: 1
MIS: 0
-
: send the line "unsubscribe linux-net" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
