Hello all, On my HP tc2120 server onboard Broadcom NIC doesn't work under vanilla 2.4.24 kernel. But it works under 2.4.24-grsec. Strange... read on... xen:~ # lspci 00:00.0 Host bridge: ServerWorks GCNB-LE Host Bridge (rev 32) 00:00.1 Host bridge: ServerWorks GCNB-LE Host Bridge 00:03.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5702 Gigabit Ethernet (rev 02) 00:04.0 SCSI storage controller: Adaptec AIC-7892A U160/m (rev 02) 00:06.0 Ethernet controller: 3Com Corporation 3c905C-TX/TX-M [Tornado] (rev 78) 00:09.0 VGA compatible controller: ATI Technologies Inc Rage XL (rev 27) 00:0f.0 ISA bridge: ServerWorks CSB6 South Bridge (rev a0) 00:0f.1 IDE interface: ServerWorks CSB6 RAID/IDE Controller (rev a0) 00:0f.2 USB Controller: ServerWorks CSB6 OHCI USB Controller (rev 05) 00:0f.3 Host bridge: ServerWorks GCLE-2 Host Bridge 2.4.24: tg3.c:v2.3 (November 5, 2003) tg3: Could not obtain valid ethernet address, aborting. 2.4.24-grsec: tg3.c:v2.3 (November 5, 2003) eth0: Tigon3 [partno(BCM95702A20) rev 1002 PHY(5703)] (PCI:33MHz:32-bit) 10/100/1000BaseT Ethernet 00:08:02:f7:c1:fa tg3: eth0: Link is up at 100 Mbps, full duplex. tg3: eth0: Flow control is off for TX and off for RX. Complete kernel boot logs differ only in memory usage and CPU speed detection. Complete logs are attached.
xen:~ # cat /var/log/boot.msg Inspecting /boot/System.map-2.4.24 Loaded 18092 symbols from /boot/System.map-2.4.24. Symbols match kernel version 2.4.24. No module symbols loaded. klogd 1.4.1, log source = ksyslog started. version 17, address 0xfec02000, IRQ 32-47 <6>ACPI: INT_SRC_OVR (bus[0] irq[0x0] global_irq[0x2] polarity[0x0] trigger[0x1]) <6>ACPI: INT_SRC_OVR (bus[0] irq[0x9] global_irq[0x9] polarity[0x3] trigger[0x3]) <4>ACPI BALANCE SET <6>Using ACPI (MADT) for SMP configuration information <4>Kernel command line: root=/dev/sda3 <6>Initializing CPU#0 <4>Detected 2665.999 MHz processor. <4>Console: colour VGA+ 80x25 <4>Calibrating delay loop... 5321.52 BogoMIPS <6>Memory: 1033492k/1048556k available (1462k kernel code, 14676k reserved, 490k data, 104k init, 131052k highmem) <6>Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes) <6>Inode cache hash table entries: 65536 (order: 7, 524288 bytes) <6>Mount cache hash table entries: 512 (order: 0, 4096 bytes) <6>Buffer cache hash table entries: 65536 (order: 6, 262144 bytes) <4>Page-cache hash table entries: 262144 (order: 8, 1048576 bytes) <6>CPU: Trace cache: 12K uops, L1 D cache: 8K <6>CPU: L2 cache: 512K <6>Intel machine check architecture supported. <6>Intel machine check reporting enabled on CPU#0. <7>CPU: After generic, caps: bfebfbff 00000000 00000000 00000000 <7>CPU: Common caps: bfebfbff 00000000 00000000 00000000 <4>CPU: Intel(R) Pentium(R) 4 CPU 2.66GHz stepping 09 <6>Enabling fast FPU save and restore... done. <6>Enabling unmasked SIMD FPU exception support... done. <6>Checking 'hlt' instruction... OK. <4>POSIX conformance testing by UNIFIX <4>enabled ExtINT on CPU#0 <4>ESR value before enabling vector: 00000000 <4>ESR value after enabling vector: 00000000 <4>ENABLING IO-APIC IRQs <7>init IO_APIC IRQs <7> IO-APIC (apicid-pin) 2-0, 3-0, 3-1, 3-2, 3-3, 3-4, 3-5, 3-6, 3-7, 3-8, 3-9, 3-10, 3-11, 3-12, 3-13, 3-14, 3-15, 4-0, 4-1, 4-2, 4-3, 4-4, 4-5, 4-6, 4-7, 4-8, 4-9, 4-10, 4-11, 4-12, 4-13, 4-14, 4-15 not connected. <6>..TIMER: vector=0x31 pin1=2 pin2=-1 <3>..MP-BIOS bug: 8254 timer not connected to IO-APIC <6>...trying to set up timer (IRQ0) through the 8259A ... failed. <6>...trying to set up timer as Virtual Wire IRQ... works. <4>Using local APIC timer interrupts. <4>calibrating APIC timer ... <4>..... CPU clock speed is 2666.1897 MHz. <4>..... host bus clock speed is 133.3092 MHz. <4>cpu: 0, clocks: 1333092, slice: 666546 <4>CPU0<T0:1333088,T1:666528,D:14,S:666546,C:1333092> <4>mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au) <4>mtrr: detected mtrr type: Intel <6>ACPI: Subsystem revision 20031002 <6>PCI: PCI BIOS revision 2.10 entry at 0xf17b0, last bus=0 <6>PCI: Using configuration type 1 <7>IOAPIC[0]: Set PCI routing entry (2-9 -> 0x71 -> IRQ 9 Mode:1 Active:1) <6>ACPI: Interpreter enabled <6>ACPI: Using IOAPIC for interrupt routing <6>ACPI: System [ACPI] (supports S0 S1 S4 S5) <4>ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 11 12 14 15) <4>ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 10 11 12 14 15) <4>ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 10 11 *12 14 15) <4>ACPI: PCI Interrupt Link [LNKD] (IRQs *3 4 5 6 7 9 10 11 12 14 15) <4>ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 11 12 14 15) <4>ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 *5 6 7 9 10 11 12 14 15) <4>ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 9 10 11 12 14 15) <4>ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 9 10 11 12 14 15) <4>ACPI: PCI Interrupt Link [LNKI] (IRQs 3 4 5 6 7 9 10 11 12 14 15) <4>ACPI: PCI Interrupt Link [LNKJ] (IRQs 3 4 5 6 7 9 10 11 12 14 15) <4>ACPI: PCI Interrupt Link [LNKK] (IRQs 3 4 5 6 7 9 10 11 12 14 15) <4>ACPI: PCI Interrupt Link [LNKL] (IRQs 3 4 5 6 7 9 10 11 12 14 15) <4>ACPI: PCI Interrupt Link [LNKM] (IRQs 3 4 5 6 7 9 10 11 12 14 15) <4>ACPI: PCI Interrupt Link [LNKN] (IRQs 3 4 5 6 7 9 10 11 12 14 15) <4>ACPI: PCI Interrupt Link [LNKO] (IRQs 3 4 5 6 7 9 10 11 12 14 15) <4>ACPI: PCI Interrupt Link [LNKP] (IRQs 3 4 5 6 7 9 10 11 12 14 15) <4>ACPI: PCI Interrupt Link [LNKQ] (IRQs 3 4 5 6 7 9 10 11 12 14 15) <4>ACPI: PCI Interrupt Link [LNKR] (IRQs 3 4 5 6 7 9 10 11 12 14 15) <4>ACPI: PCI Interrupt Link [LNKS] (IRQs 3 4 5 6 7 9 10 11 12 14 15) <4>ACPI: PCI Interrupt Link [LNKT] (IRQs 3 4 5 6 7 9 10 11 12 14 15) <4>ACPI: PCI Interrupt Link [LNKU] (IRQs 3 4 5 6 7 9 10 11 12 14 15) <4>ACPI: PCI Interrupt Link [LNKV] (IRQs 3 4 5 6 7 9 10 11 12 14 15) <4>ACPI: PCI Interrupt Link [LNKW] (IRQs 3 4 5 6 7 9 10 11 12 14 15) <4>ACPI: PCI Interrupt Link [LNKX] (IRQs 3 4 5 6 7 9 10 11 12 14 15) <4>ACPI: PCI Interrupt Link [LNKY] (IRQs 3 4 5 6 7 9 10 11 12 14 15) <4>ACPI: PCI Interrupt Link [LNKZ] (IRQs 3 4 5 6 7 9 10 11 12 14 15) <4>ACPI: PCI Interrupt Link [LNK0] (IRQs 3 4 5 6 7 9 10 11 12 14 15) <4>ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 5 6 7 9 10 11 12 14 15) <4>ACPI: PCI Interrupt Link [LNK2] (IRQs 3 4 5 6 7 9 10 11 12 14 15) <4>ACPI: PCI Interrupt Link [LNK3] (IRQs 3 4 5 6 7 9 10 11 12 14 15) <4>ACPI: PCI Interrupt Link [LNK4] (IRQs 11) <4>ACPI: PCI Interrupt Link [LNK5] (IRQs 5 10 11 12 14 15) <6>ACPI: PCI Root Bridge [PCI0] (00:00) <4>PCI: Probing PCI hardware (bus 00) <6>PCI: Ignoring BAR0-3 of IDE controller 00:0f.1 <7>ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] <6>ACPI: Power Resource [FDDP] (off) <6>ACPI: Power Resource [LPTP] (off) <6>ACPI: Power Resource [URP1] (off) <6>ACPI: Power Resource [URP2] (off) <6>PCI: Probing PCI hardware <4>_CRS returns NULL! Using IRQ 10 fordevice (PCI Interrupt Link [LNK5]). <4>ACPI: PCI Interrupt Link [LNK5] enabled at IRQ 10 <7>IOAPIC[0]: Set PCI routing entry (2-10 -> 0x79 -> IRQ 10 Mode:1 Active:1) <7>00:00:0f[A] -> 2-10 -> IRQ 10 <4>_CRS returns NULL! Using IRQ 11 fordevice (PCI Interrupt Link [LNK4]). <4>ACPI: PCI Interrupt Link [LNK4] enabled at IRQ 11 <7>IOAPIC[0]: Set PCI routing entry (2-11 -> 0x81 -> IRQ 11 Mode:1 Active:1) <7>00:00:0e[A] -> 2-11 -> IRQ 11 <7>Pin 2-11 already programmed <7>Pin 2-11 already programmed <7>Pin 2-11 already programmed <7>IOAPIC[1]: Set PCI routing entry (3-1 -> 0xa9 -> IRQ 17 Mode:1 Active:1) <7>00:00:09[A] -> 3-1 -> IRQ 17 <7>IOAPIC[1]: Set PCI routing entry (3-2 -> 0xb1 -> IRQ 18 Mode:1 Active:1) <7>00:00:03[A] -> 3-2 -> IRQ 18 <7>IOAPIC[1]: Set PCI routing entry (3-15 -> 0xb9 -> IRQ 31 Mode:1 Active:1) <7>00:00:02[A] -> 3-15 -> IRQ 31 <7>IOAPIC[1]: Set PCI routing entry (3-3 -> 0xc1 -> IRQ 19 Mode:1 Active:1) <7>00:00:04[A] -> 3-3 -> IRQ 19 <7>IOAPIC[1]: Set PCI routing entry (3-8 -> 0xc9 -> IRQ 24 Mode:1 Active:1) <7>00:00:04[B] -> 3-8 -> IRQ 24 <7>IOAPIC[1]: Set PCI routing entry (3-13 -> 0xd1 -> IRQ 29 Mode:1 Active:1) <7>00:00:04[C] -> 3-13 -> IRQ 29 <7>IOAPIC[1]: Set PCI routing entry (3-10 -> 0xd9 -> IRQ 26 Mode:1 Active:1) <7>00:00:04[D] -> 3-10 -> IRQ 26 <7>IOAPIC[1]: Set PCI routing entry (3-4 -> 0xe1 -> IRQ 20 Mode:1 Active:1) <7>00:00:05[A] -> 3-4 -> IRQ 20 <7>IOAPIC[1]: Set PCI routing entry (3-9 -> 0xe9 -> IRQ 25 Mode:1 Active:1) <7>00:00:05[B] -> 3-9 -> IRQ 25 <7>IOAPIC[1]: Set PCI routing entry (3-14 -> 0x32 -> IRQ 30 Mode:1 Active:1) <7>00:00:05[C] -> 3-14 -> IRQ 30 <7>IOAPIC[1]: Set PCI routing entry (3-11 -> 0x3a -> IRQ 27 Mode:1 Active:1) <7>00:00:05[D] -> 3-11 -> IRQ 27 <7>IOAPIC[1]: Set PCI routing entry (3-5 -> 0x42 -> IRQ 21 Mode:1 Active:1) <7>00:00:06[A] -> 3-5 -> IRQ 21 <7>Pin 3-10 already programmed <7>Pin 3-15 already programmed <7>IOAPIC[1]: Set PCI routing entry (3-12 -> 0x4a -> IRQ 28 Mode:1 Active:1) <7>00:00:06[D] -> 3-12 -> IRQ 28 <7>IOAPIC[1]: Set PCI routing entry (3-6 -> 0x52 -> IRQ 22 Mode:1 Active:1) <7>00:00:07[A] -> 3-6 -> IRQ 22 <7>Pin 3-11 already programmed <7>Pin 3-8 already programmed <7>Pin 3-13 already programmed <7>IOAPIC[1]: Set PCI routing entry (3-7 -> 0x5a -> IRQ 23 Mode:1 Active:1) <7>00:00:08[A] -> 3-7 -> IRQ 23 <7>Pin 3-12 already programmed <7>Pin 3-9 already programmed <7>Pin 3-14 already programmed <7>number of MP IRQ sources: 15. <7>number of IO-APIC #2 registers: 16. <7>number of IO-APIC #3 registers: 16. <7>number of IO-APIC #4 registers: 16. <6>testing the IO APIC....................... <4> <7>IO APIC #2...... <7>.... register #00: 02000000 <7>....... : physical APIC id: 02 <7>....... : Delivery Type: 0 <7>....... : LTS : 0 <7>.... register #01: 000F0011 <7>....... : max redirection entries: 000F <7>....... : PRQ implemented: 0 <7>....... : IO APIC version: 0011 <7>.... register #02: 02000000 <7>....... : arbitration: 02 <7>.... IRQ redirection table: <7> NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect: <7> 00 000 00 1 0 0 0 0 0 0 00 <7> 01 001 01 0 0 0 0 0 1 1 39 <7> 02 000 00 1 0 0 0 0 0 0 00 <7> 03 001 01 0 0 0 0 0 1 1 41 <7> 04 001 01 0 0 0 0 0 1 1 49 <7> 05 001 01 0 0 0 0 0 1 1 51 <7> 06 001 01 0 0 0 0 0 1 1 59 <7> 07 001 01 0 0 0 0 0 1 1 61 <7> 08 001 01 0 0 0 0 0 1 1 69 <7> 09 001 01 0 1 0 1 0 1 1 71 <7> 0a 001 01 1 1 0 1 0 1 1 79 <7> 0b 001 01 1 1 0 1 0 1 1 81 <7> 0c 001 01 0 0 0 0 0 1 1 89 <7> 0d 001 01 0 0 0 0 0 1 1 91 <7> 0e 001 01 0 0 0 0 0 1 1 99 <7> 0f 001 01 0 0 0 0 0 1 1 A1 <4> <7>IO APIC #3...... <7>.... register #00: 03000000 <7>....... : physical APIC id: 03 <7>....... : Delivery Type: 0 <7>....... : LTS : 0 <7>.... register #01: 000F0011 <7>....... : max redirection entries: 000F <7>....... : PRQ implemented: 0 <7>....... : IO APIC version: 0011 <7>.... register #02: 03000000 <7>....... : arbitration: 03 <7>.... IRQ redirection table: <7> NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect: <7> 00 000 00 1 0 0 0 0 0 0 00 <7> 01 001 01 1 1 0 1 0 1 1 A9 <7> 02 001 01 1 1 0 1 0 1 1 B1 <7> 03 001 01 1 1 0 1 0 1 1 C1 <7> 04 001 01 1 1 0 1 0 1 1 E1 <7> 05 001 01 1 1 0 1 0 1 1 42 <7> 06 001 01 1 1 0 1 0 1 1 52 <7> 07 001 01 1 1 0 1 0 1 1 5A <7> 08 001 01 1 1 0 1 0 1 1 C9 <7> 09 001 01 1 1 0 1 0 1 1 E9 <7> 0a 001 01 1 1 0 1 0 1 1 D9 <7> 0b 001 01 1 1 0 1 0 1 1 3A <7> 0c 001 01 1 1 0 1 0 1 1 4A <7> 0d 001 01 1 1 0 1 0 1 1 D1 <7> 0e 001 01 1 1 0 1 0 1 1 32 <7> 0f 001 01 1 1 0 1 0 1 1 B9 <4> <7>IO APIC #4...... <7>.... register #00: 04000000 <7>....... : physical APIC id: 04 <7>....... : Delivery Type: 0 <7>....... : LTS : 0 <7>.... register #01: 000F0011 <7>....... : max redirection entries: 000F <7>....... : PRQ implemented: 0 <7>....... : IO APIC version: 0011 <7>.... register #02: 04000000 <7>....... : arbitration: 04 <7>.... IRQ redirection table: <7> NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect: <7> 00 000 00 1 0 0 0 0 0 0 00 <7> 01 000 00 1 0 0 0 0 0 0 00 <7> 02 000 00 1 0 0 0 0 0 0 00 <7> 03 000 00 1 0 0 0 0 0 0 00 <7> 04 000 00 1 0 0 0 0 0 0 00 <7> 05 000 00 1 0 0 0 0 0 0 00 <7> 06 000 00 1 0 0 0 0 0 0 00 <7> 07 000 00 1 0 0 0 0 0 0 00 <7> 08 000 00 1 0 0 0 0 0 0 00 <7> 09 000 00 1 0 0 0 0 0 0 00 <7> 0a 000 00 1 0 0 0 0 0 0 00 <7> 0b 000 00 1 0 0 0 0 0 0 00 <7> 0c 000 00 1 0 0 0 0 0 0 00 <7> 0d 000 00 1 0 0 0 0 0 0 00 <7> 0e 000 00 1 0 0 0 0 0 0 00 <7> 0f 000 00 1 0 0 0 0 0 0 00 <7>IRQ to pin mappings: <7>IRQ0 -> 0:2 <7>IRQ1 -> 0:1 <7>IRQ3 -> 0:3 <7>IRQ4 -> 0:4 <7>IRQ5 -> 0:5 <7>IRQ6 -> 0:6 <7>IRQ7 -> 0:7 <7>IRQ8 -> 0:8 <7>IRQ9 -> 0:9-> 0:9 <7>IRQ10 -> 0:10-> 0:10 <7>IRQ11 -> 0:11-> 0:11 <7>IRQ12 -> 0:12 <7>IRQ13 -> 0:13 <7>IRQ14 -> 0:14 <7>IRQ15 -> 0:15 <7>IRQ17 -> 1:1 <7>IRQ18 -> 1:2 <7>IRQ19 -> 1:3 <7>IRQ20 -> 1:4 <7>IRQ21 -> 1:5 <7>IRQ22 -> 1:6 <7>IRQ23 -> 1:7 <7>IRQ24 -> 1:8 <7>IRQ25 -> 1:9 <7>IRQ26 -> 1:10 <7>IRQ27 -> 1:11 <7>IRQ28 -> 1:12 <7>IRQ29 -> 1:13 <7>IRQ30 -> 1:14 <7>IRQ31 -> 1:15 <6>.................................... done. <6>PCI: Using ACPI for IRQ routing <6>PCI: if you experience problems, try using option 'pci=noacpi' or even 'acpi=off' <6>Linux NET4.0 for Linux 2.4 <6>Based upon Swansea University Computer Society NET3.039 <4>Initializing RT netlink socket <4>Starting kswapd <4>allocated 32 pages and 32 bhs reserved for the highmem bounces <6>Journalled Block Device driver loaded <6>ACPI: Power Button (FF) [PWRF] <6>ACPI: Processor [CPU0] (supports C1) <6>Detected PS/2 Mouse Port. <4>pty: 256 Unix98 ptys configured <6>Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabled <6>ttyS00 at 0x03f8 (irq = 4) is a 16550A <6>Real Time Clock Driver v1.10e <6>Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4 <6>ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx <6>SvrWks CSB6: IDE controller at PCI slot 00:0f.1 <6>SvrWks CSB6: chipset revision 160 <6>SvrWks CSB6: not 100%% native mode: will probe irqs later <6> ide0: BM-DMA at 0xa400-0xa407, BIOS settings: hda:pio, hdb:pio <6> ide1: BM-DMA at 0xa408-0xa40f, BIOS settings: hdc:DMA, hdd:pio <4>hdc: HL-DT-ST CD-ROM GCR-8482B, ATAPI CD/DVD-ROM drive <4>ide1 at 0x170-0x177,0x376 on irq 15 <6>SCSI subsystem driver Revision: 1.00 <6>scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.36 <4> <Adaptec (Compaq OEM) 29160 Ultra160 SCSI adapter> <4> aic7892: Ultra160 Wide Channel A, SCSI Id=7, 32/253 SCBs <4> <4>(scsi0:A:0): 160.000MB/s transfers (80.000MHz DT, offset 127, 16bit) <4>(scsi0:A:1): 160.000MB/s transfers (80.000MHz DT, offset 127, 16bit) <4>(scsi0:A:2): 160.000MB/s transfers (80.000MHz DT, offset 127, 16bit) <4> Vendor: COMPAQ Model: BD03695CC8 Rev: HPB6 <4> Type: Direct-Access ANSI SCSI revision: 03 <4> Vendor: MAXTOR Model: ATLAS10K4_36WLS Rev: DFV0 <4> Type: Direct-Access ANSI SCSI revision: 03 <4> Vendor: MAXTOR Model: ATLAS10K4_36WLS Rev: DFV0 <4> Type: Direct-Access ANSI SCSI revision: 03 <4>scsi0:A:0:0: Tagged Queuing enabled. Depth 32 <4>scsi0:A:1:0: Tagged Queuing enabled. Depth 32 <4>scsi0:A:2:0: Tagged Queuing enabled. Depth 32 <4>Attached scsi disk sda at scsi0, channel 0, id 0, lun 0 <4>Attached scsi disk sdb at scsi0, channel 0, id 1, lun 0 <4>Attached scsi disk sdc at scsi0, channel 0, id 2, lun 0 <4>SCSI device sda: 71132000 512-byte hdwr sectors (36420 MB) <6>Partition check: <6> sda: sda1 sda2 sda3 sda4 <4>SCSI device sdb: 71833096 512-byte hdwr sectors (36779 MB) <6> sdb: sdb1 <4>SCSI device sdc: 71833096 512-byte hdwr sectors (36779 MB) <6> sdc: unknown partition table <6>md: linear personality registered as nr 1 <6>md: raid0 personality registered as nr 2 <6>md: raid1 personality registered as nr 3 <6>md: raid5 personality registered as nr 4 <6>raid5: measuring checksumming speed <4> 8regs : 3109.200 MB/sec <4> 32regs : 1892.400 MB/sec <4> pIII_sse : 3476.400 MB/sec <4> pII_mmx : 3092.800 MB/sec <4> p5_mmx : 3078.400 MB/sec <4>raid5: using function: pIII_sse (3476.400 MB/sec) <6>md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27 <6>md: Autodetecting RAID arrays. <6>md: autorun ... <6>md: ... autorun DONE. <6>Initializing Cryptographic API <6>NET4: Linux TCP/IP 1.0 for NET4.0 <6>IP Protocols: ICMP, UDP, TCP, IGMP <6>IP: routing cache hash table of 8192 buckets, 64Kbytes <6>TCP: Hash tables configured (established 262144 bind 65536) <6>NET4: Unix domain sockets 1.0/SMP for Linux NET4.0. <6>kjournald starting. Commit interval 5 seconds <6>EXT3-fs: mounted filesystem with ordered data mode. <4>VFS: Mounted root (ext3 filesystem) readonly. <6>Freeing unused kernel memory: 104k freed <6>md: Autodetecting RAID arrays. <6>md: autorun ... <6>md: ... autorun DONE. <6>Adding Swap: 530136k swap-space (priority 42) <6>EXT3 FS 2.4-0.9.19, 19 August 2002 on sd(8,3), internal journal <6>kjournald starting. Commit interval 5 seconds <6>EXT3 FS 2.4-0.9.19, 19 August 2002 on sd(8,1), internal journal <6>EXT3-fs: mounted filesystem with ordered data mode. Kernel logging (ksyslog) stopped. Kernel log daemon terminating.
xen:~ # cat /var/log/boot.msg Inspecting /boot/System.map-2.4.24-grsec Loaded 18394 symbols from /boot/System.map-2.4.24-grsec. Symbols match kernel version 2.4.24. No module symbols loaded. klogd 1.4.1, log source = ksyslog started. version 17, address 0xfec02000, IRQ 32-47 <6>ACPI: INT_SRC_OVR (bus[0] irq[0x0] global_irq[0x2] polarity[0x0] trigger[0x1]) <6>ACPI: INT_SRC_OVR (bus[0] irq[0x9] global_irq[0x9] polarity[0x3] trigger[0x3]) <4>ACPI BALANCE SET <6>Using ACPI (MADT) for SMP configuration information <4>Kernel command line: root=/dev/sda3 <6>Initializing CPU#0 <4>Detected 2665.999 MHz processor. <4>Console: colour VGA+ 80x25 <4>Calibrating delay loop... 5321.52 BogoMIPS <6>Memory: 1033324k/1048556k available (1572k kernel code, 14844k reserved, 307k data, 116k init, 131052k highmem) <6>Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes) <6>Inode cache hash table entries: 65536 (order: 7, 524288 bytes) <6>Mount cache hash table entries: 512 (order: 0, 4096 bytes) <6>Buffer cache hash table entries: 65536 (order: 6, 262144 bytes) <4>Page-cache hash table entries: 262144 (order: 8, 1048576 bytes) <6>CPU: Trace cache: 12K uops, L1 D cache: 8K <6>CPU: L2 cache: 512K <6>Intel machine check architecture supported. <6>Intel machine check reporting enabled on CPU#0. <7>CPU: After generic, caps: bfebfbff 00000000 00000000 00000000 <7>CPU: Common caps: bfebfbff 00000000 00000000 00000000 <4>CPU: Intel(R) Pentium(R) 4 CPU 2.66GHz stepping 09 <6>Enabling fast FPU save and restore... done. <6>Enabling unmasked SIMD FPU exception support... done. <6>Checking 'hlt' instruction... OK. <4>POSIX conformance testing by UNIFIX <4>enabled ExtINT on CPU#0 <4>ESR value before enabling vector: 00000000 <4>ESR value after enabling vector: 00000000 <4>ENABLING IO-APIC IRQs <7>init IO_APIC IRQs <7> IO-APIC (apicid-pin) 2-0, 3-0, 3-1, 3-2, 3-3, 3-4, 3-5, 3-6, 3-7, 3-8, 3-9, 3-10, 3-11, 3-12, 3-13, 3-14, 3-15, 4-0, 4-1, 4-2, 4-3, 4-4, 4-5, 4-6, 4-7, 4-8, 4-9, 4-10, 4-11, 4-12, 4-13, 4-14, 4-15 not connected. <6>..TIMER: vector=0x31 pin1=2 pin2=-1 <3>..MP-BIOS bug: 8254 timer not connected to IO-APIC <6>...trying to set up timer (IRQ0) through the 8259A ... failed. <6>...trying to set up timer as Virtual Wire IRQ... works. <4>Using local APIC timer interrupts. <4>calibrating APIC timer ... <4>..... CPU clock speed is 2665.8824 MHz. <4>..... host bus clock speed is 133.2940 MHz. <4>cpu: 0, clocks: 1332940, slice: 666470 <4>CPU0<T0:1332928,T1:666448,D:10,S:666470,C:1332940> <4>mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au) <4>mtrr: detected mtrr type: Intel <6>ACPI: Subsystem revision 20031002 <6>PCI: PCI BIOS revision 2.10 entry at 0xf17b0, last bus=0 <6>PCI: Using configuration type 1 <7>IOAPIC[0]: Set PCI routing entry (2-9 -> 0x71 -> IRQ 9 Mode:1 Active:1) <6>ACPI: Interpreter enabled <6>ACPI: Using IOAPIC for interrupt routing <6>ACPI: System [ACPI] (supports S0 S1 S4 S5) <4>ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 11 12 14 15) <4>ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 10 11 12 14 15) <4>ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 10 11 *12 14 15) <4>ACPI: PCI Interrupt Link [LNKD] (IRQs *3 4 5 6 7 9 10 11 12 14 15) <4>ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 11 12 14 15) <4>ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 *5 6 7 9 10 11 12 14 15) <4>ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 9 10 11 12 14 15) <4>ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 9 10 11 12 14 15) <4>ACPI: PCI Interrupt Link [LNKI] (IRQs 3 4 5 6 7 9 10 11 12 14 15) <4>ACPI: PCI Interrupt Link [LNKJ] (IRQs 3 4 5 6 7 9 10 11 12 14 15) <4>ACPI: PCI Interrupt Link [LNKK] (IRQs 3 4 5 6 7 9 10 11 12 14 15) <4>ACPI: PCI Interrupt Link [LNKL] (IRQs 3 4 5 6 7 9 10 11 12 14 15) <4>ACPI: PCI Interrupt Link [LNKM] (IRQs 3 4 5 6 7 9 10 11 12 14 15) <4>ACPI: PCI Interrupt Link [LNKN] (IRQs 3 4 5 6 7 9 10 11 12 14 15) <4>ACPI: PCI Interrupt Link [LNKO] (IRQs 3 4 5 6 7 9 10 11 12 14 15) <4>ACPI: PCI Interrupt Link [LNKP] (IRQs 3 4 5 6 7 9 10 11 12 14 15) <4>ACPI: PCI Interrupt Link [LNKQ] (IRQs 3 4 5 6 7 9 10 11 12 14 15) <4>ACPI: PCI Interrupt Link [LNKR] (IRQs 3 4 5 6 7 9 10 11 12 14 15) <4>ACPI: PCI Interrupt Link [LNKS] (IRQs 3 4 5 6 7 9 10 11 12 14 15) <4>ACPI: PCI Interrupt Link [LNKT] (IRQs 3 4 5 6 7 9 10 11 12 14 15) <4>ACPI: PCI Interrupt Link [LNKU] (IRQs 3 4 5 6 7 9 10 11 12 14 15) <4>ACPI: PCI Interrupt Link [LNKV] (IRQs 3 4 5 6 7 9 10 11 12 14 15) <4>ACPI: PCI Interrupt Link [LNKW] (IRQs 3 4 5 6 7 9 10 11 12 14 15) <4>ACPI: PCI Interrupt Link [LNKX] (IRQs 3 4 5 6 7 9 10 11 12 14 15) <4>ACPI: PCI Interrupt Link [LNKY] (IRQs 3 4 5 6 7 9 10 11 12 14 15) <4>ACPI: PCI Interrupt Link [LNKZ] (IRQs 3 4 5 6 7 9 10 11 12 14 15) <4>ACPI: PCI Interrupt Link [LNK0] (IRQs 3 4 5 6 7 9 10 11 12 14 15) <4>ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 5 6 7 9 10 11 12 14 15) <4>ACPI: PCI Interrupt Link [LNK2] (IRQs 3 4 5 6 7 9 10 11 12 14 15) <4>ACPI: PCI Interrupt Link [LNK3] (IRQs 3 4 5 6 7 9 10 11 12 14 15) <4>ACPI: PCI Interrupt Link [LNK4] (IRQs 11) <4>ACPI: PCI Interrupt Link [LNK5] (IRQs 5 10 11 12 14 15) <6>ACPI: PCI Root Bridge [PCI0] (00:00) <4>PCI: Probing PCI hardware (bus 00) <6>PCI: Ignoring BAR0-3 of IDE controller 00:0f.1 <7>ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] <6>ACPI: Power Resource [FDDP] (off) <6>ACPI: Power Resource [LPTP] (off) <6>ACPI: Power Resource [URP1] (off) <6>ACPI: Power Resource [URP2] (off) <6>PCI: Probing PCI hardware <4>_CRS returns NULL! Using IRQ 10 fordevice (PCI Interrupt Link [LNK5]). <4>ACPI: PCI Interrupt Link [LNK5] enabled at IRQ 10 <7>IOAPIC[0]: Set PCI routing entry (2-10 -> 0x79 -> IRQ 10 Mode:1 Active:1) <7>00:00:0f[A] -> 2-10 -> IRQ 10 <4>_CRS returns NULL! Using IRQ 11 fordevice (PCI Interrupt Link [LNK4]). <4>ACPI: PCI Interrupt Link [LNK4] enabled at IRQ 11 <7>IOAPIC[0]: Set PCI routing entry (2-11 -> 0x81 -> IRQ 11 Mode:1 Active:1) <7>00:00:0e[A] -> 2-11 -> IRQ 11 <7>Pin 2-11 already programmed <7>Pin 2-11 already programmed <7>Pin 2-11 already programmed <7>IOAPIC[1]: Set PCI routing entry (3-1 -> 0xa9 -> IRQ 17 Mode:1 Active:1) <7>00:00:09[A] -> 3-1 -> IRQ 17 <7>IOAPIC[1]: Set PCI routing entry (3-2 -> 0xb1 -> IRQ 18 Mode:1 Active:1) <7>00:00:03[A] -> 3-2 -> IRQ 18 <7>IOAPIC[1]: Set PCI routing entry (3-15 -> 0xb9 -> IRQ 31 Mode:1 Active:1) <7>00:00:02[A] -> 3-15 -> IRQ 31 <7>IOAPIC[1]: Set PCI routing entry (3-3 -> 0xc1 -> IRQ 19 Mode:1 Active:1) <7>00:00:04[A] -> 3-3 -> IRQ 19 <7>IOAPIC[1]: Set PCI routing entry (3-8 -> 0xc9 -> IRQ 24 Mode:1 Active:1) <7>00:00:04[B] -> 3-8 -> IRQ 24 <7>IOAPIC[1]: Set PCI routing entry (3-13 -> 0xd1 -> IRQ 29 Mode:1 Active:1) <7>00:00:04[C] -> 3-13 -> IRQ 29 <7>IOAPIC[1]: Set PCI routing entry (3-10 -> 0xd9 -> IRQ 26 Mode:1 Active:1) <7>00:00:04[D] -> 3-10 -> IRQ 26 <7>IOAPIC[1]: Set PCI routing entry (3-4 -> 0xe1 -> IRQ 20 Mode:1 Active:1) <7>00:00:05[A] -> 3-4 -> IRQ 20 <7>IOAPIC[1]: Set PCI routing entry (3-9 -> 0xe9 -> IRQ 25 Mode:1 Active:1) <7>00:00:05[B] -> 3-9 -> IRQ 25 <7>IOAPIC[1]: Set PCI routing entry (3-14 -> 0x32 -> IRQ 30 Mode:1 Active:1) <7>00:00:05[C] -> 3-14 -> IRQ 30 <7>IOAPIC[1]: Set PCI routing entry (3-11 -> 0x3a -> IRQ 27 Mode:1 Active:1) <7>00:00:05[D] -> 3-11 -> IRQ 27 <7>IOAPIC[1]: Set PCI routing entry (3-5 -> 0x42 -> IRQ 21 Mode:1 Active:1) <7>00:00:06[A] -> 3-5 -> IRQ 21 <7>Pin 3-10 already programmed <7>Pin 3-15 already programmed <7>IOAPIC[1]: Set PCI routing entry (3-12 -> 0x4a -> IRQ 28 Mode:1 Active:1) <7>00:00:06[D] -> 3-12 -> IRQ 28 <7>IOAPIC[1]: Set PCI routing entry (3-6 -> 0x52 -> IRQ 22 Mode:1 Active:1) <7>00:00:07[A] -> 3-6 -> IRQ 22 <7>Pin 3-11 already programmed <7>Pin 3-8 already programmed <7>Pin 3-13 already programmed <7>IOAPIC[1]: Set PCI routing entry (3-7 -> 0x5a -> IRQ 23 Mode:1 Active:1) <7>00:00:08[A] -> 3-7 -> IRQ 23 <7>Pin 3-12 already programmed <7>Pin 3-9 already programmed <7>Pin 3-14 already programmed <7>number of MP IRQ sources: 15. <7>number of IO-APIC #2 registers: 16. <7>number of IO-APIC #3 registers: 16. <7>number of IO-APIC #4 registers: 16. <6>testing the IO APIC....................... <4> <7>IO APIC #2...... <7>.... register #00: 02000000 <7>....... : physical APIC id: 02 <7>....... : Delivery Type: 0 <7>....... : LTS : 0 <7>.... register #01: 000F0011 <7>....... : max redirection entries: 000F <7>....... : PRQ implemented: 0 <7>....... : IO APIC version: 0011 <7>.... register #02: 02000000 <7>....... : arbitration: 02 <7>.... IRQ redirection table: <7> NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect: <7> 00 000 00 1 0 0 0 0 0 0 00 <7> 01 001 01 0 0 0 0 0 1 1 39 <7> 02 000 00 1 0 0 0 0 0 0 00 <7> 03 001 01 0 0 0 0 0 1 1 41 <7> 04 001 01 0 0 0 0 0 1 1 49 <7> 05 001 01 0 0 0 0 0 1 1 51 <7> 06 001 01 0 0 0 0 0 1 1 59 <7> 07 001 01 0 0 0 0 0 1 1 61 <7> 08 001 01 0 0 0 0 0 1 1 69 <7> 09 001 01 0 1 0 1 0 1 1 71 <7> 0a 001 01 1 1 0 1 0 1 1 79 <7> 0b 001 01 1 1 0 1 0 1 1 81 <7> 0c 001 01 0 0 0 0 0 1 1 89 <7> 0d 001 01 0 0 0 0 0 1 1 91 <7> 0e 001 01 0 0 0 0 0 1 1 99 <7> 0f 001 01 0 0 0 0 0 1 1 A1 <4> <7>IO APIC #3...... <7>.... register #00: 03000000 <7>....... : physical APIC id: 03 <7>....... : Delivery Type: 0 <7>....... : LTS : 0 <7>.... register #01: 000F0011 <7>....... : max redirection entries: 000F <7>....... : PRQ implemented: 0 <7>....... : IO APIC version: 0011 <7>.... register #02: 03000000 <7>....... : arbitration: 03 <7>.... IRQ redirection table: <7> NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect: <7> 00 000 00 1 0 0 0 0 0 0 00 <7> 01 001 01 1 1 0 1 0 1 1 A9 <7> 02 001 01 1 1 0 1 0 1 1 B1 <7> 03 001 01 1 1 0 1 0 1 1 C1 <7> 04 001 01 1 1 0 1 0 1 1 E1 <7> 05 001 01 1 1 0 1 0 1 1 42 <7> 06 001 01 1 1 0 1 0 1 1 52 <7> 07 001 01 1 1 0 1 0 1 1 5A <7> 08 001 01 1 1 0 1 0 1 1 C9 <7> 09 001 01 1 1 0 1 0 1 1 E9 <7> 0a 001 01 1 1 0 1 0 1 1 D9 <7> 0b 001 01 1 1 0 1 0 1 1 3A <7> 0c 001 01 1 1 0 1 0 1 1 4A <7> 0d 001 01 1 1 0 1 0 1 1 D1 <7> 0e 001 01 1 1 0 1 0 1 1 32 <7> 0f 001 01 1 1 0 1 0 1 1 B9 <4> <7>IO APIC #4...... <7>.... register #00: 04000000 <7>....... : physical APIC id: 04 <7>....... : Delivery Type: 0 <7>....... : LTS : 0 <7>.... register #01: 000F0011 <7>....... : max redirection entries: 000F <7>....... : PRQ implemented: 0 <7>....... : IO APIC version: 0011 <7>.... register #02: 04000000 <7>....... : arbitration: 04 <7>.... IRQ redirection table: <7> NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect: <7> 00 000 00 1 0 0 0 0 0 0 00 <7> 01 000 00 1 0 0 0 0 0 0 00 <7> 02 000 00 1 0 0 0 0 0 0 00 <7> 03 000 00 1 0 0 0 0 0 0 00 <7> 04 000 00 1 0 0 0 0 0 0 00 <7> 05 000 00 1 0 0 0 0 0 0 00 <7> 06 000 00 1 0 0 0 0 0 0 00 <7> 07 000 00 1 0 0 0 0 0 0 00 <7> 08 000 00 1 0 0 0 0 0 0 00 <7> 09 000 00 1 0 0 0 0 0 0 00 <7> 0a 000 00 1 0 0 0 0 0 0 00 <7> 0b 000 00 1 0 0 0 0 0 0 00 <7> 0c 000 00 1 0 0 0 0 0 0 00 <7> 0d 000 00 1 0 0 0 0 0 0 00 <7> 0e 000 00 1 0 0 0 0 0 0 00 <7> 0f 000 00 1 0 0 0 0 0 0 00 <7>IRQ to pin mappings: <7>IRQ0 -> 0:2 <7>IRQ1 -> 0:1 <7>IRQ3 -> 0:3 <7>IRQ4 -> 0:4 <7>IRQ5 -> 0:5 <7>IRQ6 -> 0:6 <7>IRQ7 -> 0:7 <7>IRQ8 -> 0:8 <7>IRQ9 -> 0:9-> 0:9 <7>IRQ10 -> 0:10-> 0:10 <7>IRQ11 -> 0:11-> 0:11 <7>IRQ12 -> 0:12 <7>IRQ13 -> 0:13 <7>IRQ14 -> 0:14 <7>IRQ15 -> 0:15 <7>IRQ17 -> 1:1 <7>IRQ18 -> 1:2 <7>IRQ19 -> 1:3 <7>IRQ20 -> 1:4 <7>IRQ21 -> 1:5 <7>IRQ22 -> 1:6 <7>IRQ23 -> 1:7 <7>IRQ24 -> 1:8 <7>IRQ25 -> 1:9 <7>IRQ26 -> 1:10 <7>IRQ27 -> 1:11 <7>IRQ28 -> 1:12 <7>IRQ29 -> 1:13 <7>IRQ30 -> 1:14 <7>IRQ31 -> 1:15 <6>.................................... done. <6>PCI: Using ACPI for IRQ routing <6>PCI: if you experience problems, try using option 'pci=noacpi' or even 'acpi=off' <6>Linux NET4.0 for Linux 2.4 <6>Based upon Swansea University Computer Society NET3.039 <4>Initializing RT netlink socket <4>Starting kswapd <4>allocated 32 pages and 32 bhs reserved for the highmem bounces <6>Journalled Block Device driver loaded <6>ACPI: Power Button (FF) [PWRF] <6>ACPI: Processor [CPU0] (supports C1) <6>Detected PS/2 Mouse Port. <4>pty: 256 Unix98 ptys configured <6>Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabled <6>ttyS00 at 0x03f8 (irq = 4) is a 16550A <6>Real Time Clock Driver v1.10e <6>Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4 <6>ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx <6>SvrWks CSB6: IDE controller at PCI slot 00:0f.1 <6>SvrWks CSB6: chipset revision 160 <6>SvrWks CSB6: not 100%% native mode: will probe irqs later <6> ide0: BM-DMA at 0xa400-0xa407, BIOS settings: hda:pio, hdb:pio <6> ide1: BM-DMA at 0xa408-0xa40f, BIOS settings: hdc:DMA, hdd:pio <4>hdc: HL-DT-ST CD-ROM GCR-8482B, ATAPI CD/DVD-ROM drive <4>ide1 at 0x170-0x177,0x376 on irq 15 <6>SCSI subsystem driver Revision: 1.00 <6>scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.36 <4> <Adaptec (Compaq OEM) 29160 Ultra160 SCSI adapter> <4> aic7892: Ultra160 Wide Channel A, SCSI Id=7, 32/253 SCBs <4> <4>(scsi0:A:0): 160.000MB/s transfers (80.000MHz DT, offset 127, 16bit) <4>(scsi0:A:1): 160.000MB/s transfers (80.000MHz DT, offset 127, 16bit) <4>(scsi0:A:2): 160.000MB/s transfers (80.000MHz DT, offset 127, 16bit) <4> Vendor: COMPAQ Model: BD03695CC8 Rev: HPB6 <4> Type: Direct-Access ANSI SCSI revision: 03 <4> Vendor: MAXTOR Model: ATLAS10K4_36WLS Rev: DFV0 <4> Type: Direct-Access ANSI SCSI revision: 03 <4> Vendor: MAXTOR Model: ATLAS10K4_36WLS Rev: DFV0 <4> Type: Direct-Access ANSI SCSI revision: 03 <4>scsi0:A:0:0: Tagged Queuing enabled. Depth 32 <4>scsi0:A:1:0: Tagged Queuing enabled. Depth 32 <4>scsi0:A:2:0: Tagged Queuing enabled. Depth 32 <4>Attached scsi disk sda at scsi0, channel 0, id 0, lun 0 <4>Attached scsi disk sdb at scsi0, channel 0, id 1, lun 0 <4>Attached scsi disk sdc at scsi0, channel 0, id 2, lun 0 <4>SCSI device sda: 71132000 512-byte hdwr sectors (36420 MB) <6>Partition check: <6> sda: sda1 sda2 sda3 sda4 <4>SCSI device sdb: 71833096 512-byte hdwr sectors (36779 MB) <6> sdb: sdb1 <4>SCSI device sdc: 71833096 512-byte hdwr sectors (36779 MB) <6> sdc: unknown partition table <6>md: linear personality registered as nr 1 <6>md: raid0 personality registered as nr 2 <6>md: raid1 personality registered as nr 3 <6>md: raid5 personality registered as nr 4 <6>raid5: measuring checksumming speed <4> 8regs : 3140.400 MB/sec <4> 32regs : 1874.800 MB/sec <4> pIII_sse : 3485.600 MB/sec <4> pII_mmx : 3118.000 MB/sec <4> p5_mmx : 3110.000 MB/sec <4>raid5: using function: pIII_sse (3485.600 MB/sec) <6>md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27 <6>md: Autodetecting RAID arrays. <6>md: autorun ... <6>md: ... autorun DONE. <6>Initializing Cryptographic API <6>NET4: Linux TCP/IP 1.0 for NET4.0 <6>IP Protocols: ICMP, UDP, TCP, IGMP <6>IP: routing cache hash table of 8192 buckets, 64Kbytes <6>TCP: Hash tables configured (established 262144 bind 65536) <6>NET4: Unix domain sockets 1.0/SMP for Linux NET4.0. <6>kjournald starting. Commit interval 5 seconds <6>EXT3-fs: mounted filesystem with ordered data mode. <4>VFS: Mounted root (ext3 filesystem) readonly. <6>Freeing unused kernel memory: 116k freed <6>md: Autodetecting RAID arrays. <6>md: autorun ... <6>md: ... autorun DONE. <6>Adding Swap: 530136k swap-space (priority 42) <6>EXT3 FS 2.4-0.9.19, 19 August 2002 on sd(8,3), internal journal <6>kjournald starting. Commit interval 5 seconds <6>EXT3 FS 2.4-0.9.19, 19 August 2002 on sd(8,1), internal journal <6>EXT3-fs: mounted filesystem with ordered data mode. Kernel logging (ksyslog) stopped. Kernel log daemon terminating.