bash-2.05a# ./ethtool -d eth0
RealTek RTL-8139C registers:
------------------------------
0x00: MAC Address 00:40:f4:55:9d:95
0x08: Multicast Address Filter 0x80000000 0x00000000
0x10: Transmit Status Desc 0 0x9008a03e
0x14: Transmit Status Desc 1 0x9008a072
0x18: Transmit Status Desc 2 0x9008a03c
0x1C: Transmit Status Desc 3 0x9008a072
0x20: Transmit Start Addr 0 0x1e256000
0x24: Transmit Start Addr 1 0x1e256600
0x28: Transmit Start Addr 2 0x1e256c00
0x2C: Transmit Start Addr 3 0x1e257200
0x30: Rx buffer addr (C mode) 0x1e470000
0x34: Early Rx Byte Count 0
0x36: Early Rx Status 0x0a
ERxGood ERxOverWrite
0x37: Command 0x0d
Rx on, Tx on
0x38: Current Address of Packet Read (C mode) 0x7464
0x3A: Current Rx buffer address (C mode) 0x7474
0x3C: Interrupt Mask 0xc07f
SERR TimeOut RxFIFO LinkChg RxNoBuf TxErr TxOK RxErr RxOK
0x3E: Interrupt Status 0x0000
0x40: Tx Configuration 0x74000680
0x44: Rx Configuration 0x0000f78e
0x48: Timer count 0x070d8b0e
0x4C: Missed packet counter 0x000000
0x50: EEPROM Command 0x00
0x51: Config 0 0x10
0x52: Config 1 0x8d
0x54: Timer interrupt 0x00000000
0x58: Media status 0x18
0x59: Config 3 0xc1
0x5A: Config 4 0x88
0x5C: Multiple Interrupt Select 0x0000
0x5E: PCI revision id 0x10
0x60: Transmit Status of All Desc (C mode) 0xf00f
0x62: MII Basic Mode Control Register 0x1000
0x64: MII Basic Mode Status Register 0x782d
0x66: MII Autonegotiation Advertising 0x01e1
0x68: MII Link Partner Ability 0x0000
0x6A: MII Expansion 0x0000
0x6C: MII Disconnect counter 0x0000
0x6E: MII False carrier sense counter 0x0000
0x70: MII Nway test 0x0005
0x72: MII RX_ER counter 0x0000
0x74: MII CS configuration 0x77c0
0x78: PHY parameter 1 0xb0f243b9
0x7C: Twister parameter 0x7a36d743
0x80: PHY parameter 2 0x1a
0x84: PM CRC for wakeup frame 0 0xff
0x85: PM CRC for wakeup frame 1 0xff
0x86: PM CRC for wakeup frame 2 0xff
0x87: PM CRC for wakeup frame 3 0xff
0x88: PM CRC for wakeup frame 4 0xff
0x89: PM CRC for wakeup frame 5 0xff
0x8A: PM CRC for wakeup frame 6 0xff
0x8B: PM CRC for wakeup frame 7 0xff
0x8C: PM wakeup frame 0 0xffffffff 0xffffffff
0x94: PM wakeup frame 1 0xffffffff 0xffffffff
0x9C: PM wakeup frame 2 0xffffffff 0xffffffff
0xA4: PM wakeup frame 3 0xffffffff 0xffffffff
0xAC: PM wakeup frame 4 0xffffffff 0xffffffff
0xB4: PM wakeup frame 5 0xffffffff 0xffffffff
0xBC: PM wakeup frame 6 0xffffffff 0xffffffff
0xC4: PM wakeup frame 7 0xffffffff 0xffffffff
0xCC: PM LSB CRC for wakeup frame 0 0xff
0xCD: PM LSB CRC for wakeup frame 1 0xff
0xCE: PM LSB CRC for wakeup frame 2 0xff
0xCF: PM LSB CRC for wakeup frame 3 0xff
0xD0: PM LSB CRC for wakeup frame 4 0xff
0xD1: PM LSB CRC for wakeup frame 5 0xff
0xD2: PM LSB CRC for wakeup frame 6 0xff
0xD3: PM LSB CRC for wakeup frame 7 0xff
0xD4: Flash memory read/write 0x00000000
0xD8: Config 5 0x03
bash-2.05a#
--- Begin Message ---Hi all.
- To: linux-net@vger.kernel.org
- Subject: [2.4] 8139too driver gives many errors and collisions
- From: Marcello <voloterreno@tin.it>
- Date: Fri, 10 Oct 2003 21:32:11 +0200
- User-agent: Mozilla/5.0 (X11; U; Linux i686; en-US; rv:1.4) Gecko/20031006
I'm using 2 Ethernet card based on the chip RTL8139C made by Skintek. These cards work with the 8139too.o module (that I've tried to build with various options) , but I get on both the boards , with variuous Cables tried the same error:
During the connection I get very much collsions and also some error packages under a very low connection load .
In paricular I have an ADSL Ethernet Modem , that is plugged to one of these cards , and using various file sharing programs like xMule immediatly I get collisions , and my connection is only 256Kbit/s !!!
This is the result of a "ping -f _modem_" : bash-2.05a# ping -f 192.168.254.254 PING 192.168.254.254 (192.168.254.254): 56 octets data ............................................................................... --- 192.168.254.254 ping statistics --- 2664 packets transmitted, 2585 packets received, 2% packet loss round-trip min/avg/max = 0.8/19.0/42.8 ms bash-2.05a#
and this is the "ifconfig" output after that : bash-2.05a# ifconfig eth0 Link encap:Ethernet HWaddr 00:40:F4:55:9D:95 inet addr:192.168.254.1 Bcast:192.168.254.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:7611 errors:0 dropped:0 overruns:0 frame:0 TX packets:7479 errors:0 dropped:0 overruns:0 carrier:0 collisions:4847 txqueuelen:1000 RX bytes:765102 (747.1 Kb) TX bytes:729649 (712.5 Kb) Interrupt:17 Base address:0x8f00
eth1 Link encap:Ethernet HWaddr 00:40:F4:55:A1:40 inet addr:192.168.254.2 Bcast:192.168.254.255 Mask:255.255.255.0 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) Interrupt:19 Base address:0xae00
lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:2 errors:0 dropped:0 overruns:0 frame:0 TX packets:2 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:100 (100.0 b) TX bytes:100 (100.0 b)
As you can see collisions are very much .
I haven't this problem with the 2.4.21-gentoo_modified kernel and with the new 2.6.0-test7 kernel , so it seems to be a Kernel problem .
Another strange problem that seems to be Kernel indipendent is that the autonegotiation fails :
bash-2.05a# mii-tool -v eth0: autonegotiation failed, link ok product info: vendor 00:00:00, model 0 rev 0 basic mode: autonegotiation enabled basic status: autonegotiation complete, link ok capabilities: 100baseTx-FD 100baseTx-HD 10baseT-FD 10baseT-HD advertising: 100baseTx-FD 100baseTx-HD 10baseT-FD 10baseT-HD eth1: no link product info: vendor 00:00:00, model 0 rev 0 basic mode: autonegotiation enabled basic status: no link capabilities: 100baseTx-FD 100baseTx-HD 10baseT-FD 10baseT-HD advertising: 100baseTx-FD 100baseTx-HD 10baseT-FD 10baseT-HD bash-2.05a#
Please, Help me to find a solution to this! :(
Thank you very much!
Marcello
(Here the dmesg) : bash-2.05a# dmesg Linux version 2.4.23-pre7 (root@melchior.magisystem.it) (gcc version 3.2.3 (CRUX)) #4 Fri Oct 10 20:03:16 CEST 2003 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) BIOS-e820: 00000000000cc000 - 00000000000d0000 (reserved) BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000001fff0000 (usable) BIOS-e820: 000000001fff0000 - 000000001fff8000 (ACPI data) BIOS-e820: 000000001fff8000 - 0000000020000000 (ACPI NVS) BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved) BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved) BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved) 511MB LOWMEM available. ACPI: have wakeup address 0xc0001000 found SMP MP-table at 000fb930 hm, page 000fb000 reserved twice. hm, page 000fc000 reserved twice. hm, page 000f6000 reserved twice. hm, page 000f7000 reserved twice. On node 0 totalpages: 131056 zone(0): 4096 pages. zone(1): 126960 pages. zone(2): 0 pages. ACPI: RSDP (v000 AMI ) @ 0x000fa9c0 ACPI: RSDT (v001 AMIINT VIA_K7 0x00000010 MSFT 0x00000097) @ 0x1fff0000 ACPI: FADT (v001 AMIINT VIA_K7 0x00000011 MSFT 0x00000097) @ 0x1fff0030 ACPI: MADT (v001 AMIINT VIA_K7 0x00000009 MSFT 0x00000097) @ 0x1fff00c0 ACPI: DSDT (v001 VIA VIA_K7 0x00001000 MSFT 0x0100000d) @ 0x00000000 ACPI: Local APIC address 0xfee00000 ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled) Processor #0 Pentium(tm) Pro APIC version 16 ACPI: IOAPIC (id[0x02] address[0xfec00000] global_irq_base[0x0]) IOAPIC[0]: Assigned apic_id 2 IOAPIC[0]: apic_id 2, version 3, address 0xfec00000, IRQ 0-23 ACPI: INT_SRC_OVR (bus[0] irq[0x0] global_irq[0x2] polarity[0x0] trigger[0x0]) ACPI: INT_SRC_OVR (bus[0] irq[0x9] global_irq[0x9] polarity[0x3] trigger[0x3]) Using ACPI (MADT) for SMP configuration information Kernel command line: auto BOOT_IMAGE=CRUX ro root=303 hdc=ide-scsi hdd=ide-scsi ide_setup: hdc=ide-scsi ide_setup: hdd=ide-scsi Initializing CPU#0 Detected 2004.627 MHz processor. Console: colour dummy device 80x25 Calibrating delay loop... 3997.69 BogoMIPS Memory: 516088k/524224k available (1254k kernel code, 7748k reserved, 466k data, 112k init, 0k highmem) Dentry cache hash table entries: 65536 (order: 7, 524288 bytes) Inode cache hash table entries: 32768 (order: 6, 262144 bytes) Mount cache hash table entries: 512 (order: 0, 4096 bytes) Buffer cache hash table entries: 32768 (order: 5, 131072 bytes) Page-cache hash table entries: 131072 (order: 7, 524288 bytes) CPU: CLK_CTL MSR was 6003d22f. Reprogramming to 2003d22f CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 256K (64 bytes/line) Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. CPU: After generic, caps: 0383fbff c1c3fbff 00000000 00000000 CPU: Common caps: 0383fbff c1c3fbff 00000000 00000000 CPU: AMD Athlon(tm) XP 2400+ stepping 01 Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Checking 'hlt' instruction... OK. POSIX conformance testing by UNIFIX enabled ExtINT on CPU#0 ESR value before enabling vector: 00000080 ESR value after enabling vector: 00000000 ENABLING IO-APIC IRQs init IO_APIC IRQs IO-APIC (apicid-pin) 2-0, 2-16, 2-17, 2-18, 2-19, 2-20, 2-21, 2-22, 2-23 not connected. ..TIMER: vector=0x31 pin1=2 pin2=0 number of MP IRQ sources: 16. number of IO-APIC #2 registers: 24. testing the IO APIC.......................
IO APIC #2...... .... register #00: 02000000 ....... : physical APIC id: 02 ....... : Delivery Type: 0 ....... : LTS : 0 .... register #01: 00178003 ....... : max redirection entries: 0017 ....... : PRQ implemented: 1 ....... : IO APIC version: 0003 .... IRQ redirection table: NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect: 00 000 00 1 0 0 0 0 0 0 00 01 001 01 0 0 0 0 0 1 1 39 02 001 01 0 0 0 0 0 1 1 31 03 001 01 0 0 0 0 0 1 1 41 04 001 01 0 0 0 0 0 1 1 49 05 001 01 0 0 0 0 0 1 1 51 06 001 01 0 0 0 0 0 1 1 59 07 001 01 0 0 0 0 0 1 1 61 08 001 01 0 0 0 0 0 1 1 69 09 001 01 1 1 0 1 0 1 1 71 0a 001 01 0 0 0 0 0 1 1 79 0b 001 01 0 0 0 0 0 1 1 81 0c 001 01 0 0 0 0 0 1 1 89 0d 001 01 0 0 0 0 0 1 1 91 0e 001 01 0 0 0 0 0 1 1 99 0f 001 01 0 0 0 0 0 1 1 A1 10 000 00 1 0 0 0 0 0 0 00 11 000 00 1 0 0 0 0 0 0 00 12 000 00 1 0 0 0 0 0 0 00 13 000 00 1 0 0 0 0 0 0 00 14 000 00 1 0 0 0 0 0 0 00 15 000 00 1 0 0 0 0 0 0 00 16 000 00 1 0 0 0 0 0 0 00 17 000 00 1 0 0 0 0 0 0 00 IRQ to pin mappings: IRQ0 -> 0:2 IRQ1 -> 0:1 IRQ3 -> 0:3 IRQ4 -> 0:4 IRQ5 -> 0:5 IRQ6 -> 0:6 IRQ7 -> 0:7 IRQ8 -> 0:8 IRQ9 -> 0:9 IRQ10 -> 0:10 IRQ11 -> 0:11 IRQ12 -> 0:12 IRQ13 -> 0:13 IRQ14 -> 0:14 IRQ15 -> 0:15 .................................... done. Using local APIC timer interrupts. calibrating APIC timer ... ..... CPU clock speed is 2004.5111 MHz. ..... host bus clock speed is 334.0851 MHz. cpu: 0, clocks: 3340851, slice: 1670425 CPU0<T0:3340848,T1:1670416,D:7,S:1670425,C:3340851> mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au) mtrr: detected mtrr type: Intel ACPI: Subsystem revision 20030918 PCI: PCI BIOS revision 2.10 entry at 0xfdaf1, last bus=1 PCI: Using configuration type 1 IOAPIC[0]: Set PCI routing entry (2-9 -> 0x71 -> IRQ 9 Mode:1 Active:1) ACPI: Interpreter enabled ACPI: Using IOAPIC for interrupt routing ACPI: System [ACPI] (supports S0 S1 S4 S5) ACPI: PCI Root Bridge [PCI0] (00:00) PCI: Probing PCI hardware (bus 00) ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: Power Resource [URP1] (off) ACPI: Power Resource [URP2] (off) ACPI: Power Resource [FDDP] (off) ACPI: Power Resource [LPTP] (off) ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11 12 14 15) ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *10 11 12 14 15) ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 10 11 12 14 15) ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 6 7 10 11 12 14 15) PCI: Probing PCI hardware IOAPIC[0]: Set PCI routing entry (2-16 -> 0xa9 -> IRQ 16 Mode:1 Active:1) 00:00:01[A] -> 2-16 -> IRQ 16 IOAPIC[0]: Set PCI routing entry (2-17 -> 0xb1 -> IRQ 17 Mode:1 Active:1) 00:00:01[B] -> 2-17 -> IRQ 17 IOAPIC[0]: Set PCI routing entry (2-22 -> 0xb9 -> IRQ 22 Mode:1 Active:1) 00:00:11[C] -> 2-22 -> IRQ 22 Pin 2-16 already programmed Pin 2-17 already programmed IOAPIC[0]: Set PCI routing entry (2-18 -> 0xc1 -> IRQ 18 Mode:1 Active:1) 00:00:05[C] -> 2-18 -> IRQ 18 IOAPIC[0]: Set PCI routing entry (2-19 -> 0xc9 -> IRQ 19 Mode:1 Active:1) 00:00:05[D] -> 2-19 -> IRQ 19 Pin 2-17 already programmed Pin 2-18 already programmed Pin 2-19 already programmed Pin 2-16 already programmed Pin 2-19 already programmed Pin 2-16 already programmed Pin 2-17 already programmed Pin 2-18 already programmed Pin 2-18 already programmed Pin 2-19 already programmed Pin 2-16 already programmed Pin 2-17 already programmed Pin 2-17 already programmed Pin 2-18 already programmed Pin 2-19 already programmed Pin 2-16 already programmed Pin 2-18 already programmed Pin 2-19 already programmed Pin 2-16 already programmed Pin 2-17 already programmed Pin 2-16 already programmed Pin 2-19 already programmed Pin 2-17 already programmed IOAPIC[0]: Set PCI routing entry (2-21 -> 0xd1 -> IRQ 21 Mode:1 Active:1) 00:00:10[A] -> 2-21 -> IRQ 21 Pin 2-21 already programmed Pin 2-21 already programmed Pin 2-21 already programmed IOAPIC[0]: Set PCI routing entry (2-23 -> 0xd9 -> IRQ 23 Mode:1 Active:1) 00:00:12[A] -> 2-23 -> IRQ 23 Pin 2-18 already programmed PCI: No IRQ known for interrupt pin A of device 00:11.1 - using IRQ 255 PCI: Using ACPI for IRQ routing PCI: if you experience problems, try using option 'pci=noacpi' or even 'acpi=off' PCI: Via IRQ fixup for 00:10.0, from 11 to 5 Linux NET4.0 for Linux 2.4 Based upon Swansea University Computer Society NET3.039 Initializing RT netlink socket Starting kswapd devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au) devfs: boot_options: 0x1 vesafb: framebuffer at 0xd8000000, mapped to 0xe080b000, size 3072k vesafb: mode is 1024x768x16, linelength=2048, pages=0 vesafb: protected mode interface info at c000:bbc0 vesafb: scrolling: redraw vesafb: directcolor: size=0:5:6:5, shift=0:11:5:0 Console: switching to colour frame buffer device 128x48 fb0: VESA VGA frame buffer device pty: 256 Unix98 ptys configured Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabled ttyS00 at 0x03f8 (irq = 4) is a 16550A ttyS01 at 0x02f8 (irq = 3) is a 16550A Real Time Clock Driver v1.10e Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx VP_IDE: IDE controller at PCI slot 00:11.1 PCI: No IRQ known for interrupt pin A of device 00:11.1 - using IRQ 255 VP_IDE: chipset revision 6 VP_IDE: not 100% native mode: will probe irqs later VP_IDE: VIA vt8235 (rev 00) IDE UDMA133 controller on pci00:11.1 ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:DMA, hdb:DMA ide1: BM-DMA at 0xfc08-0xfc0f, BIOS settings: hdc:DMA, hdd:DMA hda: MAXTOR 6L060J3, ATA DISK drive hdb: QUANTUM FIREBALLP AS30.0, ATA DISK drive blk: queue c02f9100, I/O limit 4095Mb (mask 0xffffffff) blk: queue c02f923c, I/O limit 4095Mb (mask 0xffffffff) hdc: LITE-ON LTR-52246S, ATAPI CD/DVD-ROM drive hdd: _NEC DV-5800A, ATAPI CD/DVD-ROM drive ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 ide1 at 0x170-0x177,0x376 on irq 15 hda: attached ide-disk driver. hda: host protected area => 1 hda: 117266688 sectors (60041 MB) w/1819KiB Cache, CHS=7299/255/63, UDMA(133) hdb: attached ide-disk driver. hdb: host protected area => 1 hdb: 58633344 sectors (30020 MB) w/1902KiB Cache, CHS=3649/255/63, UDMA(100) Partition check: /dev/ide/host0/bus0/target0/lun0: p1 p2 p3 p4 < p5 p6 p7 p8 > /dev/ide/host0/bus0/target1/lun0: p1 NET4: Linux TCP/IP 1.0 for NET4.0 IP Protocols: ICMP, UDP, TCP, IGMP IP: routing cache hash table of 4096 buckets, 32Kbytes TCP: Hash tables configured (established 32768 bind 65536) reiserfs: found format "3.6" with standard journal reiserfs: checking transaction log (device ide0(3,3)) ... for (ide0(3,3)) ide0(3,3):Using r5 hash to sort names VFS: Mounted root (reiserfs filesystem) readonly. Mounted devfs on /dev Freeing unused kernel memory: 112k freed NET4: Unix domain sockets 1.0/SMP for Linux NET4.0. Adding Swap: 1028120k swap-space (priority -1) reiserfs: found format "3.6" with standard journal reiserfs: checking transaction log (device ide0(3,5)) ... for (ide0(3,5)) ide0(3,5):Using r5 hash to sort names reiserfs: found format "3.6" with standard journal reiserfs: checking transaction log (device ide0(3,6)) ... for (ide0(3,6)) ide0(3,6):Using r5 hash to sort names reiserfs: found format "3.6" with standard journal reiserfs: checking transaction log (device ide0(3,7)) ... for (ide0(3,7)) ide0(3,7):Using r5 hash to sort names Journalled Block Device driver loaded kjournald starting. Commit interval 5 seconds EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,2), internal journal EXT3-fs: mounted filesystem with ordered data mode. kjournald starting. Commit interval 5 seconds EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,65), internal journal EXT3-fs: mounted filesystem with ordered data mode. 8139too Fast Ethernet driver 0.9.26 eth0: RealTek RTL8139 at 0xe0e78f00, 00:40:f4:55:9d:95, IRQ 17 eth0: Identified 8139 chip type 'RTL-8139C' eth1: RealTek RTL8139 at 0xe0e7ae00, 00:40:f4:55:a1:40, IRQ 19 eth1: Identified 8139 chip type 'RTL-8139C' eth0: link up, 10Mbps, half-duplex, lpa 0x0000 eth1: link down usb.c: registered new driver hub usb.c: registered new driver hiddev usb.c: registered new driver hid hid-core.c: v1.8.1 Andreas Gal, Vojtech Pavlik <vojtech@suse.cz> hid-core.c: USB HID support drivers usb-uhci.c: $Revision: 1.275 $ time 20:07:17 Oct 10 2003 usb-uhci.c: High bandwidth mode enabled usb-uhci.c: USB UHCI at I/O 0xe000, IRQ 21 usb-uhci.c: Detected 2 ports usb.c: new USB bus registered, assigned bus number 1 hub.c: USB hub found hub.c: 2 ports detected usb-uhci.c: v1.275:USB Universal Host Controller Interface driver ehci_hcd 00:10.3: VIA Technologies, Inc. USB 2.0 ehci_hcd 00:10.3: irq 21, pci mem e0ea3d00 usb.c: new USB bus registered, assigned bus number 2 ehci_hcd 00:10.3: USB 2.0 enabled, EHCI 1.00, driver 2003-Jun-19/2.4 hub.c: USB hub found hub.c: 2 ports detected mice: PS/2 mouse device common for all mice hub.c: new USB device 00:10.0-1, assigned address 2 input: USB HID v1.10 Mouse [Logitech USB Receiver] on usb1:2.0 CSLIP: code copyright 1989 Regents of the University of California PPP generic driver version 2.4.2 HDLC line discipline: version $Revision: 3.7 $, maxframe=4096 N_HDLC line discipline registered. cmpci: version $Revision: 6.16 $ time 20:07:09 Oct 10 2003 cmpci: found CM8738 adapter at io 0xe400 irq 16 cmpci: chip version = 055 bash-2.05a#
--- End Message ---
