Hi Boris, > > > > > > Summary of change log > > v3: > > Add support command sequences to change octal DTR mode and based on > > part of Pratyush's patches set. > > > > v2: > > Parse BFPT & xSPI table for Octal 8D-8D-8D mode parameters and enable Octal > > mode in spi_nor_late_init_params(). > > Using Macros in spi_nor_spimem_read_data, spi_nor_spimem_write_data and > > so on by Vignesh comments. > > > > v1: > > Without parsing BFPT & xSPI profile 1.0 table and enter Octal 8D-8D-8D > > mode directly in spi_nor_fixups hooks. > > > > > > thnaks for your time and review. > > best regards, > > Mason > > > > -- > > Mason Yang (7): > > mtd: spi-nor: sfdp: get octal mode maximum speed from BFPT > > mtd: spi-nor: sfdp: parse xSPI Profile 1.0 table > > mtd: spi-nor: sfdp: parse command sequences to change octal DTR mode > > mtd: spi-nor: core: add configuration register 2 read & write support > > spi: mxic: patch for octal DTR mode support > > mtd: spi-nor: core: execute command sequences to change octal DTR mode > > mtd: spi-nor: macronix: Add Octal 8D-8D-8D supports for Macronix > > mx25uw51245g > > > > Pratyush Yadav (7): > > spi: spi-mem: allow specifying whether an op is DTR or not > > spi: spi-mem: allow specifying a command's extension > > mtd: spi-nor: add support for DTR protocol > > mtd: spi-nor: sfdp: prepare BFPT parsing for JESD216 rev D > > mtd: spi-nor: sfdp: get command opcode extension type from BFPT > > mtd: spi-nor: core: use dummy cycle and address width info from SFDP > > mtd: spi-nor: core: enable octal DTR mode when possible > > Why are you doing that?! This series is being actively worked on by > Pratyush, and all you gain by sending it on your own is more > confusion. If you have patches on top of a series that's not been > merged yet, mention the dependency in the cover letter, but don't > resend patches that have already been sent and are being reviewed. okay, much thank for your comments. Will re-submit and mention the dependency in my cover letter. Hi Pratyush, Sorry if these patches make you uncomfortable. > > I think it's time you spend a bit of time learning about the submission > process, because that's not the first mistake you do, and I'm pretty > sure I already mentioned that in my previous reviews. best regards, Mason CONFIDENTIALITY NOTE: This e-mail and any attachments may contain confidential information and/or personal data, which is protected by applicable laws. Please be reminded that duplication, disclosure, distribution, or use of this e-mail (and/or its attachments) or any part thereof is prohibited. If you receive this e-mail in error, please notify us immediately and delete this mail as well as its attachment(s) from your system. In addition, please be informed that collection, processing, and/or use of personal data is prohibited unless expressly permitted by personal data protection laws. Thank you for your attention and cooperation. Macronix International Co., Ltd. ===================================================================== ============================================================================ CONFIDENTIALITY NOTE: This e-mail and any attachments may contain confidential information and/or personal data, which is protected by applicable laws. Please be reminded that duplication, disclosure, distribution, or use of this e-mail (and/or its attachments) or any part thereof is prohibited. If you receive this e-mail in error, please notify us immediately and delete this mail as well as its attachment(s) from your system. In addition, please be informed that collection, processing, and/or use of personal data is prohibited unless expressly permitted by personal data protection laws. Thank you for your attention and cooperation. Macronix International Co., Ltd. ===================================================================== ______________________________________________________ Linux MTD discussion mailing list http://lists.infradead.org/mailman/listinfo/linux-mtd/