[PATCH v3 11/14] mtd: spi-nor: core: enable octal DTR mode when possible

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



From: Pratyush Yadav <p.yadav@xxxxxx>

Allow flashes to specify a hook to enable octal DTR mode. Use this hook
whenever possible to get optimal transfer speeds.

Signed-off-by: Pratyush Yadav <p.yadav@xxxxxx>
---
 drivers/mtd/spi-nor/core.c | 35 +++++++++++++++++++++++++++++++++++
 drivers/mtd/spi-nor/core.h |  2 ++
 2 files changed, 37 insertions(+)

diff --git a/drivers/mtd/spi-nor/core.c b/drivers/mtd/spi-nor/core.c
index cbfdf544..a353830 100644
--- a/drivers/mtd/spi-nor/core.c
+++ b/drivers/mtd/spi-nor/core.c
@@ -3162,6 +3162,35 @@ static int spi_nor_init_params(struct spi_nor *nor)
 	return 0;
 }
 
+/** spi_nor_octal_dtr_enable() - enable Octal DTR I/O if needed
+ * @nor:                 pointer to a 'struct spi_nor'
+ * @enable:              whether to enable or disable Octal DTR
+ *
+ * Return: 0 on success, -errno otherwise.
+ */
+static int spi_nor_octal_dtr_enable(struct spi_nor *nor, bool enable)
+{
+	int ret;
+
+	if (!nor->params->octal_dtr_enable)
+		return 0;
+
+	if (!(nor->read_proto == SNOR_PROTO_8_8_8_DTR &&
+	      nor->write_proto == SNOR_PROTO_8_8_8_DTR))
+		return 0;
+
+	ret = nor->params->octal_dtr_enable(nor, enable);
+	if (ret)
+		return ret;
+
+	if (enable)
+		nor->reg_proto = SNOR_PROTO_8_8_8_DTR;
+	else
+		nor->reg_proto = SNOR_PROTO_1_1_1;
+
+	return 0;
+}
+
 /**
  * spi_nor_quad_enable() - enable Quad I/O if needed.
  * @nor:                pointer to a 'struct spi_nor'
@@ -3201,6 +3230,12 @@ static int spi_nor_init(struct spi_nor *nor)
 {
 	int err;
 
+	err = spi_nor_octal_dtr_enable(nor, true);
+	if (err) {
+		dev_dbg(nor->dev, "octal mode not supported\n");
+		return err;
+	}
+
 	err = spi_nor_quad_enable(nor);
 	if (err) {
 		dev_dbg(nor->dev, "quad mode not supported\n");
diff --git a/drivers/mtd/spi-nor/core.h b/drivers/mtd/spi-nor/core.h
index 91bc69a..9b0e0ba 100644
--- a/drivers/mtd/spi-nor/core.h
+++ b/drivers/mtd/spi-nor/core.h
@@ -223,6 +223,7 @@ struct cmd_seq_octal_dtr {
  * @erase_map:		the erase map parsed from the SFDP Sector Map Parameter
  *                      Table.
  * @cmd_seq:		command sequence to change to octal DTR mode.
+ * @octal_dtr_enable:	enables SPI NOR octal DTR mode.
  * @quad_enable:	enables SPI NOR quad mode.
  * @set_4byte_addr_mode: puts the SPI NOR in 4 byte addressing mode.
  * @convert_addr:	converts an absolute address into something the flash
@@ -252,6 +253,7 @@ struct spi_nor_flash_parameter {
 
 	struct cmd_seq_octal_dtr	cmd_seq[4];
 
+	int (*octal_dtr_enable)(struct spi_nor *nor, bool enable);
 	int (*quad_enable)(struct spi_nor *nor);
 	int (*set_4byte_addr_mode)(struct spi_nor *nor, bool enable);
 	u32 (*convert_addr)(struct spi_nor *nor, u32 addr);
-- 
1.9.1


______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/



[Index of Archives]     [LARTC]     [Bugtraq]     [Yosemite Forum]     [Photo]

  Powered by Linux