[PATCH v5 18/19] mtd: spi-nor: spansion: add support for Cypress Semper flash

[Pratyush Yadav <p.yadav@xxxxxx>]

The Cypress Semper flash is an xSPI compliant octal DTR flash. Add
support for using it in octal DTR mode.

The flash by default boots in a hybrid sector mode. But the sector map
table on the part I had was programmed incorrectly and the SMPT values
on the flash don't match the public datasheet. Specifically, in some
places erase type 3 was used instead of 4. In addition, the region sizes
were incorrect in some places. So, for testing I set CFR3N[3] to enable
uniform sector sizes. Since the uniform sector mode bit is a
non-volatile bit, this series does not change it to avoid making any
permanent changes to the flash configuration. The correct data to
implement a fixup is not available right now and will be done in a
follow-up patch if needed.

Signed-off-by: Pratyush Yadav <p.yadav@xxxxxx>
---
 drivers/mtd/spi-nor/spansion.c | 167 +++++++++++++++++++++++++++++++++
 1 file changed, 167 insertions(+)

diff --git a/drivers/mtd/spi-nor/spansion.c b/drivers/mtd/spi-nor/spansion.c
index 88183eba8ac1..e5dc36b70e4e 100644
--- a/drivers/mtd/spi-nor/spansion.c
+++ b/drivers/mtd/spi-nor/spansion.c
@@ -8,6 +8,169 @@
 
 #include "core.h"
 
+/* For Cypress flash. */
+#define SPINOR_OP_RD_ANY_REG			0x65	/* Read any register */
+#define SPINOR_OP_WR_ANY_REG			0x71	/* Write any register */
+#define SPINOR_REG_CYPRESS_CFR2V		0x00800003
+#define SPINOR_REG_CYPRESS_CFR2V_MEMLAT_11_24	0xb
+#define SPINOR_REG_CYPRESS_CFR3V		0x00800004
+#define SPINOR_REG_CYPRESS_CFR3V_PGSZ		BIT(4) /* Page size. */
+#define SPINOR_REG_CYPRESS_CFR5V		0x00800006
+#define SPINOR_REG_CYPRESS_CFR5V_OCT_DTR_EN	0x3
+#define SPINOR_REG_CYPRESS_CFR5V_OCT_DTR_DS	0
+#define SPINOR_OP_CYPRESS_RD_FAST		0xee
+
+/**
+ * spi_nor_cypress_octal_dtr_enable() - Enable octal DTR on Cypress flashes.
+ * @nor:		pointer to a 'struct spi_nor'
+ *
+ * This also sets the memory access latency cycles to 24 to allow the flash to
+ * run at up to 200MHz.
+ *
+ * Return: 0 on success, -errno otherwise.
+ */
+static int spi_nor_cypress_octal_dtr_enable(struct spi_nor *nor, bool enable)
+{
+	struct spi_mem_op op;
+	u8 *buf = nor->bouncebuf;
+	u8 addr_width;
+	int ret;
+
+	if (enable)
+		addr_width = 3;
+	else
+		addr_width = 4;
+
+	if (enable) {
+		/* Use 24 dummy cycles for memory array reads. */
+		ret = spi_nor_write_enable(nor);
+		if (ret)
+			return ret;
+
+		*buf = SPINOR_REG_CYPRESS_CFR2V_MEMLAT_11_24;
+		op = (struct spi_mem_op)
+			SPI_MEM_OP(SPI_MEM_OP_CMD(SPINOR_OP_WR_ANY_REG, 1),
+				   SPI_MEM_OP_ADDR(addr_width,
+						   SPINOR_REG_CYPRESS_CFR2V,
+						   1),
+				   SPI_MEM_OP_NO_DUMMY,
+				   SPI_MEM_OP_DATA_OUT(1, buf, 1));
+		ret = spi_mem_exec_op(nor->spimem, &op);
+		if (ret) {
+			dev_warn(nor->dev,
+				 "failed to set default memory latency value: %d\n",
+				 ret);
+			return ret;
+		}
+		ret = spi_nor_wait_till_ready(nor);
+		if (ret)
+			return ret;
+
+		nor->read_dummy = 24;
+	}
+
+	/* Set/unset the octal and DTR enable bits. */
+	ret = spi_nor_write_enable(nor);
+	if (ret)
+		return ret;
+
+	if (enable)
+		*buf = SPINOR_REG_CYPRESS_CFR5V_OCT_DTR_EN;
+	else
+		*buf = SPINOR_REG_CYPRESS_CFR5V_OCT_DTR_DS;
+	op = (struct spi_mem_op)
+		SPI_MEM_OP(SPI_MEM_OP_CMD(SPINOR_OP_WR_ANY_REG, 1),
+			   SPI_MEM_OP_ADDR(addr_width,
+					   SPINOR_REG_CYPRESS_CFR5V,
+					   1),
+			   SPI_MEM_OP_NO_DUMMY,
+			   SPI_MEM_OP_DATA_OUT(1, buf, 1));
+
+	if (!enable)
+		spi_nor_spimem_setup_op(nor, &op, SNOR_PROTO_8_8_8_DTR);
+
+	ret = spi_mem_exec_op(nor->spimem, &op);
+	if (ret) {
+		dev_warn(nor->dev, "Failed to enable octal DTR mode\n");
+		return ret;
+	}
+
+	return 0;
+}
+
+static void s28hs512t_default_init(struct spi_nor *nor)
+{
+	nor->params->octal_dtr_enable = spi_nor_cypress_octal_dtr_enable;
+}
+
+static void s28hs512t_post_sfdp_fixup(struct spi_nor *nor)
+{
+	/*
+	 * On older versions of the flash the xSPI Profile 1.0 table has the
+	 * 8D-8D-8D Fast Read opcode as 0x00. But it actually should be 0xEE.
+	 */
+	if (nor->params->reads[SNOR_CMD_READ_8_8_8_DTR].opcode == 0)
+		nor->params->reads[SNOR_CMD_READ_8_8_8_DTR].opcode =
+			SPINOR_OP_CYPRESS_RD_FAST;
+
+	nor->params->hwcaps.mask |= SNOR_HWCAPS_PP_8_8_8_DTR;
+
+	/* This flash is also missing the 4-byte Page Program opcode bit. */
+	spi_nor_set_pp_settings(&nor->params->page_programs[SNOR_CMD_PP],
+				SPINOR_OP_PP_4B, SNOR_PROTO_1_1_1);
+	/*
+	 * Since xSPI Page Program opcode is backward compatible with
+	 * Legacy SPI, use Legacy SPI opcode there as well.
+	 */
+	spi_nor_set_pp_settings(&nor->params->page_programs[SNOR_CMD_PP_8_8_8_DTR],
+				SPINOR_OP_PP_4B, SNOR_PROTO_8_8_8_DTR);
+
+	/*
+	 * The xSPI Profile 1.0 table advertises the number of additional
+	 * address bytes needed for Read Status Register command as 0 but the
+	 * actual value for that is 4.
+	 */
+	nor->params->rdsr_addr_nbytes = 4;
+}
+
+static int s28hs512t_post_bfpt_fixup(struct spi_nor *nor,
+				     const struct sfdp_parameter_header *bfpt_header,
+				     const struct sfdp_bfpt *bfpt,
+				     struct spi_nor_flash_parameter *params)
+{
+	struct spi_mem_op op;
+	u8 *buf = nor->bouncebuf;
+	u8 addr_width = 3;
+	int ret;
+
+	/*
+	 * The BFPT table advertises a 512B page size but the page size is
+	 * actually configurable (with the default being 256B). Read from
+	 * CFR3V[4] and set the correct size.
+	 */
+	op = (struct spi_mem_op)
+		SPI_MEM_OP(SPI_MEM_OP_CMD(SPINOR_OP_RD_ANY_REG, 1),
+			   SPI_MEM_OP_ADDR(addr_width, SPINOR_REG_CYPRESS_CFR3V, 1),
+			   SPI_MEM_OP_NO_DUMMY,
+			   SPI_MEM_OP_DATA_IN(1, buf, 1));
+	ret = spi_mem_exec_op(nor->spimem, &op);
+	if (ret)
+		return ret;
+
+	if (*buf & SPINOR_REG_CYPRESS_CFR3V_PGSZ)
+		params->page_size = 512;
+	else
+		params->page_size = 256;
+
+	return 0;
+}
+
+static struct spi_nor_fixups s28hs512t_fixups = {
+	.default_init = s28hs512t_default_init,
+	.post_sfdp = s28hs512t_post_sfdp_fixup,
+	.post_bfpt = s28hs512t_post_bfpt_fixup,
+};
+
 static const struct flash_info spansion_parts[] = {
 	/* Spansion/Cypress -- single (large) sector size only, at least
 	 * for the chips listed here (without boot sectors).
@@ -72,6 +235,10 @@ static const struct flash_info spansion_parts[] = {
 	{ "s25fl256l",  INFO(0x016019,      0,  64 * 1024, 512,
 			     SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ |
 			     SPI_NOR_4B_OPCODES) },
+	{ "s28hs512t",   INFO(0x345b1a,      0, 256 * 1024, 256,
+			     SECT_4K | SPI_NOR_OCTAL_DTR_READ)
+		.fixups = &s28hs512t_fixups,
+	},
 };
 
 static void spansion_post_sfdp_fixups(struct spi_nor *nor)
-- 
2.26.2


______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/