+ $ref: /schemas/types.yaml#/definitions/flag
+
+ st,fmc2-ebi-cs-mux-enable:
+ description: Address/Data multiplexed on databus (valid only with
+ NOR and PSRAM transactions type). By default, Address/Data
+ are not multiplexed.
+ $ref: /schemas/types.yaml#/definitions/flag
+
+ st,fmc2-ebi-cs-buswidth:
+ description: Data bus width
+ $ref: /schemas/types.yaml#/definitions/uint32
+ enum: [ 8, 16 ]
+ default: 16
+
+ st,fmc2-ebi-cs-waitpol-high:
+ description: Wait signal polarity (NWAIT signal active high).
+ By default, NWAIT is active low.
+ $ref: /schemas/types.yaml#/definitions/flag
+
+ st,fmc2-ebi-cs-waitcfg-enable:
+ description: The NWAIT signal indicates wheither the data from the
+ device are valid or if a wait state must be inserted when
+ accessing the device in synchronous mode. By default, the
+ NWAIT signal is active one data cycle before wait state.
+ $ref: /schemas/types.yaml#/definitions/flag
+
+ st,fmc2-ebi-cs-wait-enable:
+ description: The NWAIT signal is enabled (its level is taken into
+ account after the programmed latency period to insert wait
+ states if asserted). By default, the NWAIT signal is
+ disabled.
+ $ref: /schemas/types.yaml#/definitions/flag
+
+ st,fmc2-ebi-cs-asyncwait-enable:
+ description: The NWAIT signal is taken into account during asynchronous
+ transactions. By default, the NWAIT signal is not taken
+ into account during asynchronous transactions.
+ $ref: /schemas/types.yaml#/definitions/flag
+
+ st,fmc2-ebi-cs-cpsize:
+ description: CRAM page size. The controller splits the burst access
+ when the memory page is reached. By default, no burst
+ split when crossing page boundary.
+ $ref: /schemas/types.yaml#/definitions/uint32
+ enum: [ 0, 128, 256, 512, 1024 ]
+ default: 0
+
+ st,fmc2-ebi-cs-byte-lane-setup-ns:
+ description: This property configures the byte lane setup timing
+ defined in nanoseconds from NBLx low to Chip Select NEx
+ low.
+
+ st,fmc2-ebi-cs-address-setup-ns:
+ description: This property defines the duration of the address setup
+ phase in nanoseconds used for asynchronous read/write
+ transactions.
+
+ st,fmc2-ebi-cs-address-hold-ns:
+ description: This property defines the duration of the address hold
+ phase in nanoseconds used for asynchronous multiplexed
+ read/write transactions.
+
+ st,fmc2-ebi-cs-data-setup-ns:
+ description: This property defines the duration of the data setup phase
+ in nanoseconds used for asynchronous read/write
+ transactions.
+
+ st,fmc2-ebi-cs-bus-turnaround-ns:
+ description: This property defines the delay in nanoseconds between the
+ end of current read/write transaction and the next
+ transaction.
+
+ st,fmc2-ebi-cs-data-hold-ns:
+ description: This property defines the duration of the data hold phase
+ in nanoseconds used for asynchronous read/write
+ transactions.
+
+ st,fmc2-ebi-cs-clk-period-ns:
+ description: This property defines the FMC_CLK output signal period in
+ nanoseconds.
+
+ st,fmc2-ebi-cs-data-latency-ns:
+ description: This property defines the data latency before reading or
+ writing the first data in nanoseconds.
+
+ st,fmc2_ebi-cs-write-address-setup-ns:
+ description: This property defines the duration of the address setup
+ phase in nanoseconds used for asynchronous write
+ transactions.
+
+ st,fmc2-ebi-cs-write-address-hold-ns:
+ description: This property defines the duration of the address hold
+ phase in nanoseconds used for asynchronous multiplexed
+ write transactions.
+
+ st,fmc2-ebi-cs-write-data-setup-ns:
+ description: This property defines the duration of the data setup
+ phase in nanoseconds used for asynchronous write
+ transactions.
+
+ st,fmc2-ebi-cs-write-bus-turnaround-ns:
+ description: This property defines the delay between the end of current
+ write transaction and the next transaction in nanoseconds.
+
+ st,fmc2-ebi-cs-write-data-hold-ns:
+ description: This property defines the duration of the data hold phase
+ in nanoseconds used for asynchronous write transactions.
+
+ st,fmc2-ebi-cs-max-low-pulse-ns:
+ description: This property defines the maximum chip select low pulse
+ duration in nanoseconds for synchronous transactions. When
+ this timing reaches 0, the controller splits the current
+ access, toggles NE to allow device refresh and restarts a
+ new access.
+
+ required:
+ - reg
+
+required:
+ - "#address-cells"
+ - "#size-cells"
+ - compatible
+ - reg
+ - clocks
+ - ranges
+
+examples:
+ - |
+ #include <dt-bindings/interrupt-controller/arm-gic.h>
+ #include <dt-bindings/clock/stm32mp1-clks.h>
+ #include <dt-bindings/reset/stm32mp1-resets.h>
+ memory-controller@58002000 {
+ #address-cells = <2>;
+ #size-cells = <1>;
+ compatible = "st,stm32mp1-fmc2-ebi";
+ reg = <0x58002000 0x1000>;
+ clocks = <&rcc FMC_K>;
+ resets = <&rcc FMC_R>;
+
+ ranges = <0 0 0x60000000 0x04000000>, /* EBI CS 1 */
+ <1 0 0x64000000 0x04000000>, /* EBI CS 2 */
+ <2 0 0x68000000 0x04000000>, /* EBI CS 3 */
+ <3 0 0x6c000000 0x04000000>, /* EBI CS 4 */
+ <4 0 0x80000000 0x10000000>; /* NAND */
+
+ psram@0,0 {
+ compatible = "mtd-ram";
+ reg = <0 0x00000000 0x100000>;
+ bank-width = <2>;
+
+ st,fmc2-ebi-cs-transaction-type = <1>;
+ st,fmc2-ebi-cs-address-setup-ns = <60>;
+ st,fmc2-ebi-cs-data-setup-ns = <30>;
+ st,fmc2-ebi-cs-bus-turnaround-ns = <5>;
+ };
+
+ nand-controller@4,0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "st,stm32mp15-fmc2";
+ reg = <4 0x00000000 0x1000>,
+ <4 0x08010000 0x1000>,
+ <4 0x08020000 0x1000>,
+ <4 0x01000000 0x1000>,
+ <4 0x09010000 0x1000>,
+ <4 0x09020000 0x1000>;
+ interrupts = <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>;
+ dmas = <&mdma1 20 0x2 0x12000a02 0x0 0x0>,
+ <&mdma1 20 0x2 0x12000a08 0x0 0x0>,
+ <&mdma1 21 0x2 0x12000a0a 0x0 0x0>;
+ dma-names = "tx", "rx", "ecc";
+
+ nand@0 {
+ reg = <0>;
+ nand-on-flash-bbt;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ };
+ };
+ };
+
+...
--
1.9.1
