Re: [PATCH v3 8/8] mtd: rawnand: arasan: Support the hardware BCH ECC engine

[Boris Brezillon <boris.brezillon@xxxxxxxxxxxxx>]

On Thu,  7 May 2020 13:00:34 +0200
Miquel Raynal <miquel.raynal@xxxxxxxxxxx> wrote:

> Add support for the hardware ECC BCH engine.
> 
> Please mind that this engine as an important limitation:

				^has

> BCH implementation does not inform the user when an uncorrectable ECC
> error occurs. To workaround this, we avoid using the hardware engine
> in the read path and do the computation with the software BCH
> implementation, which is faster than mixing hardware (for correction)
> and software (for verification).
> 
> Signed-off-by: Miquel Raynal <miquel.raynal@xxxxxxxxxxx>
> ---
>  drivers/mtd/nand/raw/arasan-nand-controller.c | 340 ++++++++++++++++++
>  1 file changed, 340 insertions(+)
> 
> diff --git a/drivers/mtd/nand/raw/arasan-nand-controller.c b/drivers/mtd/nand/raw/arasan-nand-controller.c
> index 61ea90ecf86e..01c0a741b4cd 100644
> --- a/drivers/mtd/nand/raw/arasan-nand-controller.c
> +++ b/drivers/mtd/nand/raw/arasan-nand-controller.c
> @@ -10,6 +10,7 @@
>   *   Naga Sureshkumar Relli <nagasure@xxxxxxxxxx>
>   */
>  
> +#include <linux/bch.h>
>  #include <linux/bitfield.h>
>  #include <linux/clk.h>
>  #include <linux/delay.h>
> @@ -143,6 +144,10 @@ struct anfc_op {
>   * @strength:		Register value of the ECC strength
>   * @raddr_cycles:	Row address cycle information
>   * @caddr_cycles:	Column address cycle information
> + * @ecc_bits:		Exact number of ECC bits per syndrome
> + * @ecc_total:		Total number of ECC bytes
> + * @hw_ecc:		Buffer to store syndromes computed by hardware
> + * @bch:		BCH structure
>   */
>  struct anand {
>  	struct list_head node;
> @@ -156,6 +161,10 @@ struct anand {
>  	u32 strength;
>  	u16 raddr_cycles;
>  	u16 caddr_cycles;
> +	unsigned int ecc_bits;
> +	unsigned int ecc_total;
> +	u8 *hw_ecc;
> +	struct bch_control *bch;
>  };
>  
>  /**
> @@ -168,6 +177,7 @@ struct anand {
>   * @chips:		List of all NAND chips attached to the controller
>   * @assigned_cs:	Bitmask describing already assigned CS lines
>   * @cur_clk:		Current clock rate
> + * @errloc:		Array of errors located with soft BCH
>   * @bf:			Array of bitflips read in each ECC step
>   */
>  struct arasan_nfc {
> @@ -179,6 +189,7 @@ struct arasan_nfc {
>  	struct list_head chips;
>  	unsigned long assigned_cs;
>  	unsigned int cur_clk;
> +	unsigned int *errloc;
>  	u8 *bf;
>  };
>  
> @@ -257,6 +268,206 @@ static int anfc_len_to_steps(struct nand_chip *chip, unsigned int len)
>  	return steps;
>  }
>  
> +static void anfc_extract_ecc_bits(struct anand *anand, const u8 *ecc)
> +{
> +	struct nand_chip *chip = &anand->chip;
> +	int step;
> +
> +	memset(anand->hw_ecc, 0, chip->ecc.bytes * chip->ecc.steps);
> +
> +	for (step = 0; step < chip->ecc.steps; step++) {
> +		unsigned int src_off = anand->ecc_bits * step;
> +		u8 *dst = &anand->hw_ecc[chip->ecc.bytes * step];
> +
> +		/* Extract the syndrome, it is not necessarily aligned */
> +		nand_extract_bits(dst, ecc, src_off, anand->ecc_bits);

I don't think you need to extract all bytes ahead of time. Just move
the extraction bits to the for_each_ecc_step() loop in
anfc_read_page_hw_ecc(). This way you can make the anand->hw_ecc buffer
smaller.

> +	}
> +}
> +
> +/*
> + * When using the embedded hardware ECC engine, the controller is in charge of
> + * feeding the engine with, first, the ECC residue present in the data array.
> + * A typical read operation is:
> + * 1/ Assert the read operation by sending the relevant command/address cycles
> + *    but targeting the column of the first ECC bytes in the OOB area instead of
> + *    the main data directly.
> + * 2/ After having read the relevant number of ECC bytes, the controller uses
> + *    the RNDOUT/RNDSTART commands which are set into the "ECC Spare Command
> + *    Register" to move the pointer back at the beginning of the main data.
> + * 3/ It will read the content of the main area for a given size (pktsize) and
> + *    will feed the ECC engine with this buffer again.
> + * 4/ The ECC engine derives the ECC bytes for the given data and compare them
> + *    with the ones already received. It eventually trigger status flags and
> + *    then set the "Buffer Read Ready" flag.
> + * 5/ The corrected data is then available for reading from the data port
> + *    register.
> + *
> + * The hardware BCH ECC engine is known to be inconstent in BCH mode and never
> + * reports errors. We need to ensure we return consistent data. This involves

	     ^ uncorrectable errors

> + * knowing the primary polynomial used by the hardware engine and compute the
> + * syndrome by ourselves in the read path instead of relying on the hardware.

I would just say "Because of this bug, we have to use the
software BCH implementation in the read path."

> + */
> +static int anfc_read_page_hw_ecc(struct nand_chip *chip, u8 *buf,
> +				 int oob_required, int page)
> +{
> +	struct arasan_nfc *nfc = to_anfc(chip->controller);
> +	struct mtd_info *mtd = nand_to_mtd(chip);
> +	struct anand *anand = to_anand(chip);
> +	unsigned int len = mtd->writesize + (oob_required ? mtd->oobsize : 0);
> +	unsigned int max_bitflips = 0;
> +	dma_addr_t paddr;
> +	int step, ret;
> +	struct anfc_op nfc_op = {
> +		.pkt_reg =
> +			PKT_SIZE(chip->ecc.size) |
> +			PKT_STEPS(chip->ecc.steps),
> +		.addr1_reg =
> +			(page & 0xFF) << (8 * (anand->caddr_cycles)) |
> +			(((page >> 8) & 0xFF) << (8 * (1 + anand->caddr_cycles))),
> +		.addr2_reg =
> +			((page >> 16) & 0xFF) |
> +			ADDR2_STRENGTH(anand->strength) |
> +			ADDR2_CS(anand->cs),
> +		.cmd_reg =
> +			CMD_1(NAND_CMD_READ0) |
> +			CMD_2(NAND_CMD_READSTART) |
> +			CMD_PAGE_SIZE(anand->page_sz) |
> +			CMD_DMA_ENABLE |
> +			CMD_NADDRS(anand->caddr_cycles +
> +				   anand->raddr_cycles),
> +		.prog_reg = PROG_PGRD,
> +	};
> +
> +	paddr = dma_map_single(nfc->dev, (void *)buf, len, DMA_FROM_DEVICE);
> +	if (dma_mapping_error(nfc->dev, paddr)) {
> +		dev_err(nfc->dev, "Buffer mapping error");
> +		return -EIO;
> +	}
> +
> +	writel_relaxed(paddr, nfc->base + DMA_ADDR0_REG);
> +	writel_relaxed((paddr >> 32), nfc->base + DMA_ADDR1_REG);
> +
> +	anfc_trigger_op(nfc, &nfc_op);
> +
> +	ret = anfc_wait_for_event(nfc, XFER_COMPLETE);
> +	dma_unmap_single(nfc->dev, paddr, len, DMA_FROM_DEVICE);
> +	if (ret) {
> +		dev_err(nfc->dev, "Error reading page %d\n", page);
> +		return ret;
> +	}
> +
> +	/* Store the raw OOB bytes as well */
> +	ret = nand_change_read_column_op(chip, mtd->writesize, chip->oob_poi,
> +					 mtd->oobsize, 0);
> +	if (ret)
> +		return ret;
> +
> +	/* Extract and reorder ECC bytes */
> +	anfc_extract_ecc_bits(anand, &chip->oob_poi[mtd->oobsize -
> +						    anand->ecc_total]);
> +
> +	/*
> +	 * For each step, compute by softare the BCH syndrome over the raw data.
> +	 * Compare the theoretical amount of errors and compare with the
> +	 * hardware engine feedback.
> +	 */
> +	for (step = 0; step < chip->ecc.steps; step++) {
> +		u8 *raw_buf = &buf[step * chip->ecc.size];
> +		u8 *ecc_buf = &anand->hw_ecc[chip->ecc.bytes * step];
> +		unsigned int bit, byte;
> +		int bf, i;
> +
> +		bf = bch_decode(anand->bch, raw_buf, chip->ecc.size, ecc_buf,
> +				NULL, NULL, nfc->errloc);
> +		if (!bf) {
> +			continue;
> +		} else if (bf > 0) {
> +			for (i = 0; i < bf; i++) {
> +				/* Only correct the data, not the syndrome */
> +				if (nfc->errloc[i] < (chip->ecc.size * 8)) {
> +					bit = BIT(nfc->errloc[i] & 7);
> +					byte = nfc->errloc[i] >> 3;
> +					raw_buf[byte] ^= bit;
> +				}
> +			}
> +
> +			mtd->ecc_stats.corrected += bf;
> +			max_bitflips = max_t(unsigned int, max_bitflips, bf);
> +
> +			continue;
> +		}
> +
> +		bf = nand_check_erased_ecc_chunk(raw_buf, chip->ecc.size,
> +						 NULL, 0, NULL, 0,
> +						 chip->ecc.strength);
> +		if (bf > 0) {
> +			mtd->ecc_stats.corrected += bf;
> +			max_bitflips = max_t(unsigned int, max_bitflips, bf);
> +			memset(raw_buf, 0xFF, chip->ecc.size);
> +		} else if (bf < 0) {
> +			mtd->ecc_stats.failed++;
> +		}
> +	}
> +
> +	return 0;
> +}
> +
> +static int anfc_write_page_hw_ecc(struct nand_chip *chip, const u8 *buf,
> +				  int oob_required, int page)
> +{
> +	struct anand *anand = to_anand(chip);
> +	struct arasan_nfc *nfc = to_anfc(chip->controller);
> +	struct mtd_info *mtd = nand_to_mtd(chip);
> +	unsigned int len = mtd->writesize + (oob_required ? mtd->oobsize : 0);
> +	dma_addr_t paddr;
> +	int ret;
> +	struct anfc_op nfc_op = {
> +		.pkt_reg =
> +			PKT_SIZE(chip->ecc.size) |
> +			PKT_STEPS(chip->ecc.steps),
> +		.addr1_reg =
> +			(page & 0xFF) << (8 * (anand->caddr_cycles)) |
> +			(((page >> 8) & 0xFF) << (8 * (1 + anand->caddr_cycles))),
> +		.addr2_reg =
> +			((page >> 16) & 0xFF) |
> +			ADDR2_STRENGTH(anand->strength) |
> +			ADDR2_CS(anand->cs),
> +		.cmd_reg =
> +			CMD_1(NAND_CMD_SEQIN) |
> +			CMD_2(NAND_CMD_PAGEPROG) |
> +			CMD_PAGE_SIZE(anand->page_sz) |
> +			CMD_DMA_ENABLE |
> +			CMD_NADDRS(anand->caddr_cycles +
> +				   anand->raddr_cycles) |
> +			CMD_ECC_ENABLE,
> +		.prog_reg = PROG_PGPROG,
> +	};
> +
> +	writel_relaxed(anand->ecc_conf, nfc->base + ECC_CONF_REG);
> +	writel_relaxed(ECC_SP_CMD1(NAND_CMD_RNDIN) |
> +		       ECC_SP_ADDRS(anand->caddr_cycles),
> +		       nfc->base + ECC_SP_REG);
> +
> +	paddr = dma_map_single(nfc->dev, (void *)buf, len, DMA_TO_DEVICE);
> +	if (dma_mapping_error(nfc->dev, paddr)) {
> +		dev_err(nfc->dev, "Buffer mapping error");
> +		return -EIO;
> +	}
> +
> +	writel_relaxed(paddr, nfc->base + DMA_ADDR0_REG);
> +	writel_relaxed((paddr >> 32), nfc->base + DMA_ADDR1_REG);
> +
> +	anfc_trigger_op(nfc, &nfc_op);
> +	ret = anfc_wait_for_event(nfc, XFER_COMPLETE);
> +	dma_unmap_single(nfc->dev, paddr, len, DMA_TO_DEVICE);
> +	if (ret)
> +		dev_err(nfc->dev, "Error writing page %d\n", page);
> +
> +	/* OOB data cannot be written here */
> +
> +	return ret;
> +}
> +
>  /* NAND framework ->exec_op() hooks and related helpers */
>  static void anfc_parse_instructions(struct nand_chip *chip,
>  				    const struct nand_subop *subop,
> @@ -599,6 +810,121 @@ static int anfc_setup_data_interface(struct nand_chip *chip, int target,
>  	return 0;
>  }
>  
> +static int anfc_init_hw_ecc_controller(struct arasan_nfc *nfc,
> +				       struct nand_chip *chip)
> +{
> +	struct anand *anand = to_anand(chip);
> +	struct mtd_info *mtd = nand_to_mtd(chip);
> +	struct nand_ecc_ctrl *ecc = &chip->ecc;
> +	unsigned int bch_prim_poly = 0, bch_gf_mag = 0, ecc_offset;
> +
> +	switch (mtd->writesize) {
> +	case SZ_512:
> +	case SZ_2K:
> +	case SZ_4K:
> +	case SZ_8K:
> +	case SZ_16K:
> +		break;
> +	default:
> +		dev_err(nfc->dev, "Unsupported page size %d\n", mtd->writesize);
> +		return -EINVAL;
> +	}
> +
> +	if (!ecc->size || !ecc->strength) {
> +		ecc->size = chip->base.eccreq.step_size;
> +		ecc->strength = chip->base.eccreq.strength;
> +	}
> +
> +	if (!ecc->size || !ecc->strength) {
> +		dev_err(nfc->dev,
> +			"Missing controller ECC step size/strength\n");
> +		return -EINVAL;
> +	}
> +
> +	switch (ecc->strength) {
> +	case 1:
> +		anand->strength = 0x0;
> +		break;
> +	case 12:
> +		anand->strength = 0x1;
> +		break;
> +	case 8:
> +		anand->strength = 0x2;
> +		break;
> +	case 4:
> +		anand->strength = 0x3;
> +		break;
> +	case 24:
> +		anand->strength = 0x4;
> +		break;
> +	default:

Maybe you should pick something that's higher than the requested
strength in that case instead of returning an error. There's generic
helper to help with that IIRC.

> +		dev_err(nfc->dev, "Unsupported strength %d\n", ecc->strength);
> +		return -EINVAL;
> +	}
> +
> +	switch (ecc->size) {
> +	case SZ_512:
> +		bch_gf_mag = 13;
> +		bch_prim_poly = 0x201b;
> +		break;
> +	case SZ_1K:
> +		bch_gf_mag = 14;
> +		bch_prim_poly = 0x4443;
> +		break;
> +	default:
> +		dev_err(nfc->dev, "Unsupported step size %d\n", ecc->strength);
> +		return -EINVAL;
> +	}
> +
> +	if ((ecc->size == SZ_1K && ecc->strength != 24) ||
> +	    (ecc->size != SZ_1K && ecc->strength == 24)) {
> +		dev_err(nfc->dev,
> +			"Unsupported couple strength/step-size: %dB/%db\n",
> +			ecc->strength, ecc->size);
> +		return -EINVAL;
> +	}
> +
> +	mtd_set_ooblayout(mtd, &nand_ooblayout_lp_ops);
> +
> +	ecc->steps = mtd->writesize / ecc->size;
> +
> +	if (ecc->strength == 1) {
> +		dev_err(nfc->dev, "Hardware Hamming engine not supported yet\n");
> +		return -EINVAL;
> +	}
> +
> +	ecc->algo = NAND_ECC_BCH;
> +	anand->ecc_bits = bch_gf_mag * ecc->strength;
> +	ecc->bytes = DIV_ROUND_UP(anand->ecc_bits, 8);
> +	anand->ecc_total = DIV_ROUND_UP(anand->ecc_bits * ecc->steps, 8);
> +	ecc_offset = mtd->writesize + mtd->oobsize - anand->ecc_total;
> +	anand->ecc_conf = ECC_CONF_COL(ecc_offset) |
> +			  ECC_CONF_LEN(anand->ecc_total) |
> +			  ECC_CONF_BCH_EN;
> +
> +	nfc->errloc = devm_kmalloc_array(nfc->dev, ecc->strength,
> +					 sizeof(*nfc->errloc), GFP_KERNEL);
> +	if (!nfc->errloc)
> +		return -ENOMEM;
> +
> +	anand->hw_ecc = devm_kmalloc(nfc->dev, ecc->steps * ecc->bytes,
> +				     GFP_KERNEL);
> +	if (!anand->hw_ecc)
> +		return -ENOMEM;
> +
> +	anand->bch = bch_init(bch_gf_mag, ecc->strength,
> +			      bch_prim_poly);
> +	if (!anand->bch)
> +		return -EINVAL;
> +
> +	anand->bch->swap_bits = true;

As mentioned in my previous reply, I don't think we should touch the
bch_control fields (even if they are exposed).

> +
> +	ecc->read_page = anfc_read_page_hw_ecc;
> +	ecc->write_page = anfc_write_page_hw_ecc;
> +
> +	return 0;
> +}
> +
>  static int anfc_attach_chip(struct nand_chip *chip)
>  {
>  	struct anand *anand = to_anand(chip);
> @@ -649,6 +975,8 @@ static int anfc_attach_chip(struct nand_chip *chip)
>  	case NAND_ECC_ON_DIE:
>  		break;
>  	case NAND_ECC_HW:
> +		ret = anfc_init_hw_ecc_controller(nfc, chip);
> +		break;
>  	default:
>  		dev_err(nfc->dev, "Unsupported ECC mode: %d\n",
>  			chip->ecc.mode);
> @@ -658,10 +986,19 @@ static int anfc_attach_chip(struct nand_chip *chip)
>  	return ret;
>  }
>  
> +static void anfc_detach_chip(struct nand_chip *chip)
> +{
> +	struct anand *anand = to_anand(chip);
> +
> +	if (anand->bch)
> +		bch_free(anand->bch);
> +}
> +
>  static const struct nand_controller_ops anfc_ops = {
>  	.exec_op = anfc_exec_op,
>  	.setup_data_interface = anfc_setup_data_interface,
>  	.attach_chip = anfc_attach_chip,
> +	.detach_chip = anfc_detach_chip,
>  };
>  
>  static int anfc_chip_init(struct arasan_nfc *nfc, struct device_node *np)
> @@ -737,6 +1074,9 @@ static void anfc_chips_cleanup(struct arasan_nfc *nfc)
>  	struct anand *anand, *tmp;
>  
>  	list_for_each_entry_safe(anand, tmp, &nfc->chips, node) {
> +		if (anand->bch)
> +			bch_free(anand->bch);
> +

Looks like you have a double-free here. I expect ->detach_chip() to be
called as part of the nand_cleanup() step.

>  		nand_release(&anand->chip);
>  		list_del(&anand->node);
>  	}


______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/