[PATCH v2 01/11] mtd: rawnand: Translate obscure bitfields into readable macros

[Miquel Raynal <miquel.raynal@xxxxxxxxxxx>]

Use the BIT() macro instead of defining a 8-digit value.

Signed-off-by: Miquel Raynal <miquel.raynal@xxxxxxxxxxx>
Reviewed-by: Boris Brezillon <boris.brezillon@xxxxxxxxxxxxx>
---
 include/linux/mtd/rawnand.h | 38 ++++++++++++++++++-------------------
 1 file changed, 19 insertions(+), 19 deletions(-)

diff --git a/include/linux/mtd/rawnand.h b/include/linux/mtd/rawnand.h
index 21873168ba4d..4b58de842340 100644
--- a/include/linux/mtd/rawnand.h
+++ b/include/linux/mtd/rawnand.h
@@ -129,36 +129,36 @@ enum nand_ecc_algo {
  * features.
  */
 /* Buswidth is 16 bit */
-#define NAND_BUSWIDTH_16	0x00000002
+#define NAND_BUSWIDTH_16	BIT(1)
 /* Chip has cache program function */
-#define NAND_CACHEPRG		0x00000008
+#define NAND_CACHEPRG		BIT(3)
 /*
  * Chip requires ready check on read (for auto-incremented sequential read).
  * True only for small page devices; large page devices do not support
  * autoincrement.
  */
-#define NAND_NEED_READRDY	0x00000100
+#define NAND_NEED_READRDY	BIT(8)
 
 /* Chip does not allow subpage writes */
-#define NAND_NO_SUBPAGE_WRITE	0x00000200
+#define NAND_NO_SUBPAGE_WRITE	BIT(9)
 
 /* Device is one of 'new' xD cards that expose fake nand command set */
-#define NAND_BROKEN_XD		0x00000400
+#define NAND_BROKEN_XD		BIT(10)
 
 /* Device behaves just like nand, but is readonly */
-#define NAND_ROM		0x00000800
+#define NAND_ROM		BIT(11)
 
 /* Device supports subpage reads */
-#define NAND_SUBPAGE_READ	0x00001000
+#define NAND_SUBPAGE_READ	BIT(12)
 
 /*
  * Some MLC NANDs need data scrambling to limit bitflips caused by repeated
  * patterns.
  */
-#define NAND_NEED_SCRAMBLING	0x00002000
+#define NAND_NEED_SCRAMBLING	BIT(13)
 
 /* Device needs 3rd row address cycle */
-#define NAND_ROW_ADDR_3		0x00004000
+#define NAND_ROW_ADDR_3		BIT(14)
 
 /* Options valid for Samsung large page devices */
 #define NAND_SAMSUNG_LP_OPTIONS NAND_CACHEPRG
@@ -173,9 +173,9 @@ enum nand_ecc_algo {
  * Position within the block: Each of these pages needs to be checked for a
  * bad block marking pattern.
  */
-#define NAND_BBM_FIRSTPAGE		0x01000000
-#define NAND_BBM_SECONDPAGE		0x02000000
-#define NAND_BBM_LASTPAGE		0x04000000
+#define NAND_BBM_FIRSTPAGE	BIT(24)
+#define NAND_BBM_SECONDPAGE	BIT(25)
+#define NAND_BBM_LASTPAGE	BIT(26)
 
 /* Position within the OOB data of the page */
 #define NAND_BBM_POS_SMALL		5
@@ -183,21 +183,21 @@ enum nand_ecc_algo {
 
 /* Non chip related options */
 /* This option skips the bbt scan during initialization. */
-#define NAND_SKIP_BBTSCAN	0x00010000
+#define NAND_SKIP_BBTSCAN	BIT(16)
 /* Chip may not exist, so silence any errors in scan */
-#define NAND_SCAN_SILENT_NODEV	0x00040000
+#define NAND_SCAN_SILENT_NODEV	BIT(18)
 /*
  * Autodetect nand buswidth with readid/onfi.
  * This suppose the driver will configure the hardware in 8 bits mode
  * when calling nand_scan_ident, and update its configuration
  * before calling nand_scan_tail.
  */
-#define NAND_BUSWIDTH_AUTO      0x00080000
+#define NAND_BUSWIDTH_AUTO      BIT(19)
 /*
  * This option could be defined by controller drivers to protect against
  * kmap'ed, vmalloc'ed highmem buffers being passed from upper layers
  */
-#define NAND_USE_BOUNCE_BUFFER	0x00100000
+#define NAND_USE_BOUNCE_BUFFER	BIT(20)
 
 /*
  * In case your controller is implementing ->legacy.cmd_ctrl() and is relying
@@ -207,20 +207,20 @@ enum nand_ecc_algo {
  * If your controller already takes care of this delay, you don't need to set
  * this flag.
  */
-#define NAND_WAIT_TCCS		0x00200000
+#define NAND_WAIT_TCCS		BIT(21)
 
 /*
  * Whether the NAND chip is a boot medium. Drivers might use this information
  * to select ECC algorithms supported by the boot ROM or similar restrictions.
  */
-#define NAND_IS_BOOT_MEDIUM	0x00400000
+#define NAND_IS_BOOT_MEDIUM	BIT(22)
 
 /*
  * Do not try to tweak the timings at runtime. This is needed when the
  * controller initializes the timings on itself or when it relies on
  * configuration done by the bootloader.
  */
-#define NAND_KEEP_TIMINGS	0x00800000
+#define NAND_KEEP_TIMINGS	BIT(23)
 
 /* Cell info constants */
 #define NAND_CI_CHIPNR_MSK	0x03
-- 
2.20.1


______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/