Re: [03/12] bus: stm32-fmc2-ebi: add STM32 FMC2 EBI controller driver

[Marek Vasut <marex@xxxxxxx>]

On 3/23/20 3:58 PM, Christophe Kerello wrote:
> The driver adds the support for the STMicroelectronics FMC2 EBI controller
> found on STM32MP SOCs.
> 

On DH STM32MP1 SoM in PDK2 carrier board,
Tested-by: Marek Vasut <marex@xxxxxxx>

btw. it seems this sets BTRx DATLAT and CLKDIV to 0xf , it's "Don't
care" in the datasheet for Muxed mode, but then it should probably be
set to 0.

The bindings I used are below:

&fmc {
        pinctrl-names = "default", "sleep";
        pinctrl-0 = <&fmc_pins_b>;
        pinctrl-1 = <&fmc_sleep_pins_b>;
        status = "okay";
        #address-cells = <1>;
        #size-cells = <1>;
        /delete-property/interrupts;
        /delete-property/dmas;
        /delete-property/dma-names;
        reg = <0x58002000 0x1000>;
        ranges;

        ebi {
                #address-cells = <2>;
                #size-cells = <1>;
                compatible = "st,stm32mp1-fmc2-ebi";
                ranges = <0 0 0x60000000 0x4000000>,
                         <1 0 0x64000000 0x4000000>,
                         <2 0 0x68000000 0x4000000>,
                         <3 0 0x6c000000 0x4000000>;

                ksz8851: ks8851mll@0,0 {
                        compatible = "micrel,ks8851-mll";
                        reg = <1 0x0 0x2 1 0x2 0x20000>;
                        interrupt-parent = <&gpioc>;
                        interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
                        bank-width = <2>;

                        /* Timing values are in nS */
                        st,fmc2_ebi_cs_mux_enable;
                        st,fmc2_ebi_cs_transaction_type = <4>;
                        st,fmc2_ebi_cs_buswidth = <16>;
                        st,fmc2_ebi_cs_address_setup = <6>;
                        st,fmc2_ebi_cs_address_hold = <6>;
                        st,fmc2_ebi_cs_data_setup = <127>;
                        st,fmc2_ebi_cs_bus_turnaround = <9>;
                        st,fmc2_ebi_cs_data_hold = <9>;
                };

                sram@3,0 {
                        compatible = "mtd-ram";
                        reg = <3 0x0 0x80000>;
                        bank-width = <2>;

                        /* Timing values are in nS */
                        st,fmc2_ebi_cs_mux_enable;
                        st,fmc2_ebi_cs_transaction_type = <4>;
                        st,fmc2_ebi_cs_buswidth = <16>;
                        st,fmc2_ebi_cs_address_setup = <6>;
                        st,fmc2_ebi_cs_address_hold = <6>;
                        st,fmc2_ebi_cs_data_setup = <127>;
                        st,fmc2_ebi_cs_bus_turnaround = <9>;
                        st,fmc2_ebi_cs_data_hold = <9>;
                };
        };
};

______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/