[PATCH v2 21/25] mtd: spi-nor: Move Xilinx bits out of core.c

[<Tudor.Ambarus@xxxxxxxxxxxxx>]

From: Boris Brezillon <bbrezillon@xxxxxxxxxx>

Create a SPI NOR manufacturer driver for Xilinx chips, and move the
Xilinx definitions outside of core.c.

While at it, remove the SPI_S3AN flag which is now useless.

Signed-off-by: Boris Brezillon <bbrezillon@xxxxxxxxxx>
Signed-off-by: Tudor Ambarus <tudor.ambarus@xxxxxxxxxxxxx>
---
 drivers/mtd/spi-nor/Makefile |  1 +
 drivers/mtd/spi-nor/core.c   | 76 +----------------------------
 drivers/mtd/spi-nor/core.h   | 13 +----
 drivers/mtd/spi-nor/xilinx.c | 94 ++++++++++++++++++++++++++++++++++++
 4 files changed, 98 insertions(+), 86 deletions(-)
 create mode 100644 drivers/mtd/spi-nor/xilinx.c

diff --git a/drivers/mtd/spi-nor/Makefile b/drivers/mtd/spi-nor/Makefile
index cd8d95b727c9..fa03513dd160 100644
--- a/drivers/mtd/spi-nor/Makefile
+++ b/drivers/mtd/spi-nor/Makefile
@@ -15,4 +15,5 @@ spi-nor-objs			+= micron-st.o
 spi-nor-objs			+= spansion.o
 spi-nor-objs			+= sst.o
 spi-nor-objs			+= winbond.o
+spi-nor-objs			+= xilinx.o
 obj-$(CONFIG_MTD_SPI_NOR)	+= spi-nor.o
diff --git a/drivers/mtd/spi-nor/core.c b/drivers/mtd/spi-nor/core.c
index 99da7d8e9097..ca2f441e2806 100644
--- a/drivers/mtd/spi-nor/core.c
+++ b/drivers/mtd/spi-nor/core.c
@@ -1095,26 +1095,6 @@ void spi_nor_unlock_and_unprep(struct spi_nor *nor)
 	mutex_unlock(&nor->lock);
 }
 
-/*
- * This code converts an address to the Default Address Mode, that has non
- * power of two page sizes. We must support this mode because it is the default
- * mode supported by Xilinx tools, it can access the whole flash area and
- * changing over to the Power-of-two mode is irreversible and corrupts the
- * original data.
- * Addr can safely be unsigned int, the biggest S3AN device is smaller than
- * 4 MiB.
- */
-static u32 s3an_convert_addr(struct spi_nor *nor, u32 addr)
-{
-	u32 offset, page;
-
-	offset = addr % nor->page_size;
-	page = addr / nor->page_size;
-	page <<= (nor->page_size > 512) ? 10 : 9;
-
-	return page | offset;
-}
-
 static u32 spi_nor_convert_addr(struct spi_nor *nor, loff_t addr)
 {
 	if (!nor->params.convert_addr)
@@ -1963,13 +1943,6 @@ int spi_nor_sr2_bit7_quad_enable(struct spi_nor *nor)
  * old entries may be missing 4K flag.
  */
 static const struct flash_info spi_nor_ids[] = {
-	/* Xilinx S3AN Internal Flash */
-	{ "3S50AN", S3AN_INFO(0x1f2200, 64, 264) },
-	{ "3S200AN", S3AN_INFO(0x1f2400, 256, 264) },
-	{ "3S400AN", S3AN_INFO(0x1f2400, 256, 264) },
-	{ "3S700AN", S3AN_INFO(0x1f2500, 512, 264) },
-	{ "3S1400AN", S3AN_INFO(0x1f2600, 512, 528) },
-
 	/* XMC (Wuhan Xinxin Semiconductor Manufacturing Corp.) */
 	{ "XM25QH64A", INFO(0x207017, 0, 64 * 1024, 128, SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
 	{ "XM25QH128A", INFO(0x207018, 0, 64 * 1024, 256, SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
@@ -1992,6 +1965,7 @@ static const struct spi_nor_manufacturer *manufacturers[] = {
 	&spi_nor_spansion,
 	&spi_nor_sst,
 	&spi_nor_winbond,
+	&spi_nor_xilinx,
 };
 
 static const struct flash_info *
@@ -2177,46 +2151,6 @@ static int spi_nor_check(struct spi_nor *nor)
 	return 0;
 }
 
-static int s3an_nor_setup(struct spi_nor *nor,
-			  const struct spi_nor_hwcaps *hwcaps)
-{
-	int ret;
-
-	ret = spi_nor_xread_sr(nor, nor->bouncebuf);
-	if (ret)
-		return ret;
-
-	nor->erase_opcode = SPINOR_OP_XSE;
-	nor->program_opcode = SPINOR_OP_XPP;
-	nor->read_opcode = SPINOR_OP_READ;
-	nor->flags |= SNOR_F_NO_OP_CHIP_ERASE;
-
-	/*
-	 * This flashes have a page size of 264 or 528 bytes (known as
-	 * Default addressing mode). It can be changed to a more standard
-	 * Power of two mode where the page size is 256/512. This comes
-	 * with a price: there is 3% less of space, the data is corrupted
-	 * and the page size cannot be changed back to default addressing
-	 * mode.
-	 *
-	 * The current addressing mode can be read from the XRDSR register
-	 * and should not be changed, because is a destructive operation.
-	 */
-	if (nor->bouncebuf[0] & XSR_PAGESIZE) {
-		/* Flash in Power of 2 mode */
-		nor->page_size = (nor->page_size == 264) ? 256 : 512;
-		nor->mtd.writebufsize = nor->page_size;
-		nor->mtd.size = 8 * nor->page_size * nor->info->n_sectors;
-		nor->mtd.erasesize = 8 * nor->page_size;
-	} else {
-		/* Flash in Default addressing mode */
-		nor->params.convert_addr = s3an_convert_addr;
-		nor->mtd.erasesize = nor->info->sector_size;
-	}
-
-	return 0;
-}
-
 static void
 spi_nor_set_read_settings(struct spi_nor_read_command *read,
 			  u8 num_mode_clocks,
@@ -2815,11 +2749,6 @@ static void spi_nor_info_init_params(struct spi_nor *nor)
 	spi_nor_init_uniform_erase_map(map, erase_mask, params->size);
 }
 
-static void s3an_post_sfdp_fixups(struct spi_nor *nor)
-{
-	nor->params.setup = s3an_nor_setup;
-}
-
 /**
  * spi_nor_post_sfdp_fixups() - Updates the flash's parameters and settings
  * after SFDP has been parsed (is also called for SPI NORs that do not
@@ -2832,9 +2761,6 @@ static void s3an_post_sfdp_fixups(struct spi_nor *nor)
  */
 static void spi_nor_post_sfdp_fixups(struct spi_nor *nor)
 {
-	if (nor->info->flags & SPI_S3AN)
-		s3an_post_sfdp_fixups(nor);
-
 	if (nor->manufacturer && nor->manufacturer->fixups &&
 	    nor->manufacturer->fixups->post_sfdp)
 		nor->manufacturer->fixups->post_sfdp(nor);
diff --git a/drivers/mtd/spi-nor/core.h b/drivers/mtd/spi-nor/core.h
index aaa2a460a159..8c666bff5768 100644
--- a/drivers/mtd/spi-nor/core.h
+++ b/drivers/mtd/spi-nor/core.h
@@ -73,16 +73,6 @@ struct flash_info {
 #define SPI_NOR_XSR_RDY		BIT(10)	/*
 					 * S3AN flashes have specific opcode to
 					 * read the status register.
-					 * Flags SPI_NOR_XSR_RDY and SPI_S3AN
-					 * use the same bit as one implies the
-					 * other, but we will get rid of
-					 * SPI_S3AN soon.
-					 */
-#define	SPI_S3AN		BIT(10)	/*
-					 * Xilinx Spartan 3AN In-System Flash
-					 * (MFR cannot be used for probing
-					 * because it has the same value as
-					 * ATMEL flashes)
 					 */
 #define SPI_NOR_4B_OPCODES	BIT(11)	/*
 					 * Use dedicated 4byte address op codes
@@ -150,7 +140,7 @@ struct flash_info {
 		.n_sectors = (_n_sectors),				\
 		.page_size = _page_size,				\
 		.addr_width = 3,					\
-		.flags = SPI_NOR_NO_FR | SPI_S3AN,
+		.flags = SPI_NOR_NO_FR | SPI_NOR_XSR_RDY,
 
 /**
  * struct spi_nor_manufacturer - SPI NOR manufacturer object
@@ -182,6 +172,7 @@ extern const struct spi_nor_manufacturer spi_nor_st;
 extern const struct spi_nor_manufacturer spi_nor_spansion;
 extern const struct spi_nor_manufacturer spi_nor_sst;
 extern const struct spi_nor_manufacturer spi_nor_winbond;
+extern const struct spi_nor_manufacturer spi_nor_xilinx;
 
 int spi_nor_write_enable(struct spi_nor *nor);
 int spi_nor_write_disable(struct spi_nor *nor);
diff --git a/drivers/mtd/spi-nor/xilinx.c b/drivers/mtd/spi-nor/xilinx.c
new file mode 100644
index 000000000000..fcf635d89f65
--- /dev/null
+++ b/drivers/mtd/spi-nor/xilinx.c
@@ -0,0 +1,94 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2005, Intec Automation Inc.
+ * Copyright (C) 2014, Freescale Semiconductor, Inc.
+ */
+
+#include <linux/mtd/spi-nor.h>
+
+#include "core.h"
+
+static const struct flash_info xilinx_parts[] = {
+	/* Xilinx S3AN Internal Flash */
+	{ "3S50AN", S3AN_INFO(0x1f2200, 64, 264) },
+	{ "3S200AN", S3AN_INFO(0x1f2400, 256, 264) },
+	{ "3S400AN", S3AN_INFO(0x1f2400, 256, 264) },
+	{ "3S700AN", S3AN_INFO(0x1f2500, 512, 264) },
+	{ "3S1400AN", S3AN_INFO(0x1f2600, 512, 528) },
+};
+
+/*
+ * This code converts an address to the Default Address Mode, that has non
+ * power of two page sizes. We must support this mode because it is the default
+ * mode supported by Xilinx tools, it can access the whole flash area and
+ * changing over to the Power-of-two mode is irreversible and corrupts the
+ * original data.
+ * Addr can safely be unsigned int, the biggest S3AN device is smaller than
+ * 4 MiB.
+ */
+static u32 s3an_convert_addr(struct spi_nor *nor, u32 addr)
+{
+	u32 offset, page;
+
+	offset = addr % nor->page_size;
+	page = addr / nor->page_size;
+	page <<= (nor->page_size > 512) ? 10 : 9;
+
+	return page | offset;
+}
+
+static int xilinx_nor_setup(struct spi_nor *nor,
+			    const struct spi_nor_hwcaps *hwcaps)
+{
+	int ret;
+
+	ret = spi_nor_xread_sr(nor, nor->bouncebuf);
+	if (ret)
+		return ret;
+
+	nor->erase_opcode = SPINOR_OP_XSE;
+	nor->program_opcode = SPINOR_OP_XPP;
+	nor->read_opcode = SPINOR_OP_READ;
+	nor->flags |= SNOR_F_NO_OP_CHIP_ERASE;
+
+	/*
+	 * This flashes have a page size of 264 or 528 bytes (known as
+	 * Default addressing mode). It can be changed to a more standard
+	 * Power of two mode where the page size is 256/512. This comes
+	 * with a price: there is 3% less of space, the data is corrupted
+	 * and the page size cannot be changed back to default addressing
+	 * mode.
+	 *
+	 * The current addressing mode can be read from the XRDSR register
+	 * and should not be changed, because is a destructive operation.
+	 */
+	if (nor->bouncebuf[0] & XSR_PAGESIZE) {
+		/* Flash in Power of 2 mode */
+		nor->page_size = (nor->page_size == 264) ? 256 : 512;
+		nor->mtd.writebufsize = nor->page_size;
+		nor->mtd.size = 8 * nor->page_size * nor->info->n_sectors;
+		nor->mtd.erasesize = 8 * nor->page_size;
+	} else {
+		/* Flash in Default addressing mode */
+		nor->params.convert_addr = s3an_convert_addr;
+		nor->mtd.erasesize = nor->info->sector_size;
+	}
+
+	return 0;
+}
+
+static void xilinx_post_sfdp_fixups(struct spi_nor *nor)
+{
+	nor->params.setup = xilinx_nor_setup;
+}
+
+static const struct spi_nor_fixups xilinx_fixups = {
+	.post_sfdp = xilinx_post_sfdp_fixups,
+};
+
+const struct spi_nor_manufacturer spi_nor_xilinx = {
+	.name = "xilinx",
+	.parts = xilinx_parts,
+	.nparts = ARRAY_SIZE(xilinx_parts),
+	.fixups = &xilinx_fixups,
+};
-- 
2.23.0

______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/