Re: [PATCH v3 05/40] mtd: rawnand: Create a new enumeration to describe properly ECC types

[Boris Brezillon <boris.brezillon@xxxxxxxxxxxxx>]

On Thu, 19 Sep 2019 21:31:05 +0200
Miquel Raynal <miquel.raynal@xxxxxxxxxxx> wrote:

> Now that the misleading mix between ECC engine type and OOB placement
> has been addressed, add a new enumeration to properly define ECC types
> (also called provider or mode).
> 
> Signed-off-by: Miquel Raynal <miquel.raynal@xxxxxxxxxxx>
> ---
>  drivers/mtd/nand/raw/nand_base.c |  7 +++++++
>  include/linux/mtd/rawnand.h      | 16 ++++++++++++++++
>  2 files changed, 23 insertions(+)
> 
> diff --git a/drivers/mtd/nand/raw/nand_base.c b/drivers/mtd/nand/raw/nand_base.c
> index 9a05ebfc44d1..00a261284aad 100644
> --- a/drivers/mtd/nand/raw/nand_base.c
> +++ b/drivers/mtd/nand/raw/nand_base.c
> @@ -4842,6 +4842,13 @@ static const char * const nand_ecc_modes[] = {
>  	[NAND_ECC_ON_DIE]	= "on-die",
>  };
>  
> +static const char * const nand_ecc_engine_providers[] = {
> +	[NAND_NO_ECC_ENGINE] = "none",
> +	[NAND_SOFT_ECC_ENGINE] = "soft",
> +	[NAND_HW_ECC_ENGINE] = "hw",
> +	[NAND_ON_DIE_ECC_ENGINE] = "on-die",
> +};
> +
>  static const char * const nand_ecc_engine_oob_placement[] = {
>  	[NAND_ECC_SYNDROME_OOB_PLACEMENT] = "hw_syndrome",
>  	[NAND_ECC_OOB_FIRST_PLACEMENT] = "hw_oob_first",
> diff --git a/include/linux/mtd/rawnand.h b/include/linux/mtd/rawnand.h
> index 1b462fb2ab77..23feab162bc2 100644
> --- a/include/linux/mtd/rawnand.h
> +++ b/include/linux/mtd/rawnand.h
> @@ -93,6 +93,22 @@ enum nand_ecc_mode {
>  	NAND_ECC_ON_DIE,
>  };
>  
> +/**
> + * enum nand_ecc_engine_type - NAND ECC engine type/provider
> + * @NAND_INVALID_ECC_ENGINE: Invalid value
> + * @NAND_NO_ECC_ENGINE: No ECC correction
> + * @NAND_SOFT_ECC_ENGINE: Software ECC correction
> + * @NAND_HW_ECC_ENGINE: Hardware (controller side) ECC correction
> + * @NAND_ON_DIE_ECC_ENGINE: Hardware (chip side) ECC correction
> + */
> +enum nand_ecc_engine_type {
> +	NAND_INVALID_ECC_ENGINE,
> +	NAND_NO_ECC_ENGINE,
> +	NAND_SOFT_ECC_ENGINE,
> +	NAND_HW_ECC_ENGINE,
> +	NAND_ON_DIE_ECC_ENGINE,
> +};
> +

No that I know where you're going, I'd recommend moving those
definitions to the generic NAND layer (or the generic ECC layer you're
about to introduce). Actually, re-ordering patches to put rawnand
changes after the introduction of the generic ECC layer might even be
simpler.

>  /**
>   * enum nand_ecc_engine_oob_placement - NAND ECC engine OOB placement
>   * @NAND_ECC_DEFAULT_OOB_PLACEMENT: Standard layout, or not specified


______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/