[PATCH for 4.4.y] mtd: cfi_cmdset_0002: Use chip_good() to retry in do_write_oneword()

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



As reported by the OpenWRT team, write requests sometimes fail on some
platforms.
Currently to check the state chip_ready() is used correctly as described by
the flash memory S29GL256P11TFI01 datasheet.
Also chip_good() is used to check if the write is succeeded and it was
implemented by the commit fb4a90bfcd6d8 ("[MTD] CFI-0002 - Improve error
checking").
But actually the write failure is caused on some platforms and also it can
be fixed by using chip_good() to check the state and retry instead.
Also it seems that it is caused after repeated about 1,000 times to retry
the write one word with the reset command.
By using chip_good() to check the state to be done it can be reduced the
retry with reset.
It is depended on the actual flash chip behavior so the root cause is
unknown.

Cc: Chris Packham <chris.packham@xxxxxxxxxxxxxxxxxxx>
Cc: Joakim Tjernlund <Joakim.Tjernlund@xxxxxxxxxxxx>
Cc: linux-mtd@xxxxxxxxxxxxxxxxxxx
Cc: stable@xxxxxxxxxxxxxxx
Reported-by: Fabio Bettoni <fbettoni@xxxxxxxxx>
Signed-off-by: Felix Fietkau <nbd@xxxxxxxx>
Signed-off-by: Hauke Mehrtens <hauke@xxxxxxxxxx>
Signed-off-by: Tokunori Ikegami <ikegami.t@xxxxxxxxx>
[vigneshr@xxxxxx: Fix a checkpatch warning]
Signed-off-by: Vignesh Raghavendra <vigneshr@xxxxxx>
---
 drivers/mtd/chips/cfi_cmdset_0002.c | 18 ++++++++++++------
 1 file changed, 12 insertions(+), 6 deletions(-)
 mode change 100644 => 100755 drivers/mtd/chips/cfi_cmdset_0002.c

diff --git a/drivers/mtd/chips/cfi_cmdset_0002.c b/drivers/mtd/chips/cfi_cmdset_0002.c
old mode 100644
new mode 100755
index fb5a3052f144..7589d891b311
--- a/drivers/mtd/chips/cfi_cmdset_0002.c
+++ b/drivers/mtd/chips/cfi_cmdset_0002.c
@@ -1626,29 +1626,35 @@ static int __xipram do_write_oneword(struct map_info *map, struct flchip *chip,
 			continue;
 		}
 
-		if (time_after(jiffies, timeo) && !chip_ready(map, adr)){
+		/*
+		 * We check "time_after" and "!chip_good" before checking
+		 * "chip_good" to avoid the failure due to scheduling.
+		 */
+		if (time_after(jiffies, timeo) && !chip_good(map, adr, datum)) {
 			xip_enable(map, chip, adr);
 			printk(KERN_WARNING "MTD %s(): software timeout\n", __func__);
 			xip_disable(map, chip, adr);
+			ret = -EIO;
 			break;
 		}
 
-		if (chip_ready(map, adr))
+		if (chip_good(map, adr, datum))
 			break;
 
 		/* Latency issues. Drop the lock, wait a while and retry */
 		UDELAY(map, chip, adr, 1);
 	}
+
 	/* Did we succeed? */
-	if (!chip_good(map, adr, datum)) {
+	if (ret) {
 		/* reset on all failures. */
 		map_write( map, CMD(0xF0), chip->start );
 		/* FIXME - should have reset delay before continuing */
 
-		if (++retry_cnt <= MAX_RETRIES)
+		if (++retry_cnt <= MAX_RETRIES) {
+			ret = 0;
 			goto retry;
-
-		ret = -EIO;
+		}
 	}
 	xip_enable(map, chip, adr);
  op_done:
-- 
2.11.0


______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/



[Index of Archives]     [LARTC]     [Bugtraq]     [Yosemite Forum]     [Photo]

  Powered by Linux