Hi Miquel,
On 30/7/19 10:28 am, Greg Ungerer wrote:
On 29/7/19 10:47 pm, Miquel Raynal wrote:
Greg Ungerer <gerg@xxxxxxxxxx> wrote on Mon, 29 Jul 2019 22:33:56 +1000:
On 29/7/19 6:36 pm, Miquel Raynal wrote:
Greg Ungerer <gerg@xxxxxxxxxx> wrote on Mon, 29 Jul 2019 16:41:51 +1000:
[snip]
nand: timing mode 5 not acknowledged by the NAND chip
What is the final timing mode used? Most of us tested in mode 5 I
guess, maybe mode 4 is broken (don't know if this is the one used here,
neither why mode 5 is refused). Can you please try by limiting the mode
to 0, 1, 2... until, hopefully, we narrow down to the failing mode.
Sure, how to do that?
This loop [1] tries to configure each mode (5, 4, ...) until one
succeeds (default is 0: must always work). Please try to limit mode to
0, 1, etc.
Mode 0 should work.
[1] https://elixir.bootlin.com/linux/v5.3-rc1/source/drivers/mtd/nand/raw/nand_base.c#L933
The normal behavior - which usually works - has
chip->onfi_timing_mode_default=5 here. So in other words on the first pass
through this loop it is checking mode 5, and setting it as the default.
I am running a test/reboot loop now waiting for failure to see
if it is still using mode 5 in that case.
With this trace in place:
--- a/linux/drivers/mtd/nand/raw/nand_base.c
+++ b/linux/drivers/mtd/nand/raw/nand_base.c
@@ -910,6 +910,7 @@ static int nand_init_data_interface(struct nand_chip *chip)
}
for (mode = fls(modes) - 1; mode >= 0; mode--) {
+ printk("%s(%d): checking mode=%d\n", __FILE__, __LINE__, mode);
ret = onfi_fill_data_interface(chip, NAND_SDR_IFACE, mode);
if (ret)
continue;
@@ -923,10 +924,12 @@ static int nand_init_data_interface(struct nand_chip *chip)
&chip->data_interface);
if (!ret) {
chip->onfi_timing_mode_default = mode;
+ printk("%s(%d): BREAKING AT mode=%d\n", __FILE__, __LINE__, mode);
break;
}
}
+ printk("%s(%d): chip->onfi_timing_mode_default=%d\n", __FILE__, __LINE__, chip->onfi_timing_mode_default);
return 0;
}
First NAND failure gives this:
nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
nand: Micron MT29F2G08ABAEAWP
nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
gpmi-nand 1806000.gpmi-nand: use legacy bch geometry
drivers/mtd/nand/raw/nand_base.c(913): checking mode=5
drivers/mtd/nand/raw/nand_base.c(927): BREAKING AT mode=5
drivers/mtd/nand/raw/nand_base.c(932): chip->onfi_timing_mode_default=5
gpmi-nand 1806000.gpmi-nand: DMA timeout, last DMA
gpmi-nand 1806000.gpmi-nand: Show GPMI registers :
gpmi-nand 1806000.gpmi-nand: offset 0x000 : 0x20830002
gpmi-nand 1806000.gpmi-nand: offset 0x010 : 0x00000000
gpmi-nand 1806000.gpmi-nand: offset 0x020 : 0x00000000
gpmi-nand 1806000.gpmi-nand: offset 0x030 : 0x00000000
gpmi-nand 1806000.gpmi-nand: offset 0x040 : 0x00000000
gpmi-nand 1806000.gpmi-nand: offset 0x050 : 0x00000000
gpmi-nand 1806000.gpmi-nand: offset 0x060 : 0x01c6800c
gpmi-nand 1806000.gpmi-nand: offset 0x070 : 0x00010101
gpmi-nand 1806000.gpmi-nand: offset 0x080 : 0xe0000000
gpmi-nand 1806000.gpmi-nand: offset 0x090 : 0x23023336
gpmi-nand 1806000.gpmi-nand: offset 0x0a0 : 0x000001ee
gpmi-nand 1806000.gpmi-nand: offset 0x0b0 : 0xff000001
gpmi-nand 1806000.gpmi-nand: offset 0x0c0 : 0x00000100
gpmi-nand 1806000.gpmi-nand: offset 0x0d0 : 0x05020000
gpmi-nand 1806000.gpmi-nand: Show BCH registers :
gpmi-nand 1806000.gpmi-nand: offset 0x000 : 0x00000100
gpmi-nand 1806000.gpmi-nand: offset 0x010 : 0x00000010
gpmi-nand 1806000.gpmi-nand: offset 0x020 : 0x00000000
gpmi-nand 1806000.gpmi-nand: offset 0x030 : 0x00000000
gpmi-nand 1806000.gpmi-nand: offset 0x040 : 0x00000000
gpmi-nand 1806000.gpmi-nand: offset 0x050 : 0x00000000
gpmi-nand 1806000.gpmi-nand: offset 0x060 : 0x00000000
gpmi-nand 1806000.gpmi-nand: offset 0x070 : 0x00000000
gpmi-nand 1806000.gpmi-nand: offset 0x080 : 0x030a2080
gpmi-nand 1806000.gpmi-nand: offset 0x090 : 0x083e2080
gpmi-nand 1806000.gpmi-nand: offset 0x0a0 : 0x070a4080
gpmi-nand 1806000.gpmi-nand: offset 0x0b0 : 0x10da4080
gpmi-nand 1806000.gpmi-nand: offset 0x0c0 : 0x070a4080
gpmi-nand 1806000.gpmi-nand: offset 0x0d0 : 0x10da4080
gpmi-nand 1806000.gpmi-nand: offset 0x0e0 : 0x070a4080
gpmi-nand 1806000.gpmi-nand: offset 0x0f0 : 0x10da4080
gpmi-nand 1806000.gpmi-nand: offset 0x100 : 0x00000000
gpmi-nand 1806000.gpmi-nand: offset 0x110 : 0x00000000
gpmi-nand 1806000.gpmi-nand: offset 0x120 : 0x00000000
gpmi-nand 1806000.gpmi-nand: offset 0x130 : 0x00000000
gpmi-nand 1806000.gpmi-nand: offset 0x140 : 0x00000000
gpmi-nand 1806000.gpmi-nand: offset 0x150 : 0x20484342
gpmi-nand 1806000.gpmi-nand: offset 0x160 : 0x01000000
gpmi-nand 1806000.gpmi-nand: offset 0x170 : 0x00000000
gpmi-nand 1806000.gpmi-nand: BCH Geometry :
GF length : 13
ECC Strength : 8
Page Size in Bytes : 2110
Metadata Size in Bytes : 10
ECC Chunk0 Size in Bytes: 512
ECC Chunkn Size in Bytes: 512
ECC Chunk Count : 4
Payload Size in Bytes : 2048
Auxiliary Size in Bytes: 16
Auxiliary Status Offset: 12
Block Mark Byte Offset : 1999
Block Mark Bit Offset : 0
gpmi-nand 1806000.gpmi-nand: Chip: 0, Error -110
nand: timing mode 5 not acknowledged by the NAND chip
gpmi-nand 1806000.gpmi-nand: Chip: 0, Error -22
Regards
Greg
______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/
