Re: [PATCH] mtd: rawnand: micron: handle "ecc off" devices correctly

[Miquel Raynal <miquel.raynal@xxxxxxxxxxx>]

+ Actual address for Boris

Miquel Raynal <miquel.raynal@xxxxxxxxxxx> wrote on Fri, 26 Jul 2019
10:28:58 +0200:

> Hi Marco,
> 
> + Richard
> + Working e-mail address for Boris
> 
> Marco Felsch <m.felsch@xxxxxxxxxxxxxx> wrote on Fri, 26 Jul 2019
> 09:44:34 +0200:
> 
> > Some devices don't support ecc "official". By "official" I mean that the
> > feature can be set trough the "SET FEATURE (EFh)" command but isn't
> > reported to the "READ ID Parameter Tables". Because the "ECC Field"
> > still says that it is disabled. This is applicable at least
> > for the MT29F2G08ABAGA and MT29F2G08ABBGA devices. Even worse the
> > datasheet describes the ECC feature in chapter "ECC Protection".
> > 
> > Currently the driver checks the "READ ID Parameter" field directly after
> > we enabled the feature. If the check fails we return immediately but
> > leave the ECC on. Now all future read/program cycles goes trough the ecc
> > and the host nfc gets confused and reports ECC errors.
> > 
> > To address this in a common way we need to turn off the ECC directly
> > after reading the "READ ID Parameter" and before checking the
> > "ECC status".
> > 
> > Signed-off-by: Marco Felsch <m.felsch@xxxxxxxxxxxxxx>
> 
> Good catch! However you report that on-die ECC correction is working
> but you still disable it; any reason to do so ? Would it be better to
> actually enable on-die ECC and explicitly mark these two chips as
> buggy (see [1] for checking the chip IDs)?
> 
> [1] https://elixir.bootlin.com/linux/v5.3-rc1/source/drivers/mtd/nand/raw/nand_macronix.c#L83
> 
> > ---
> >  drivers/mtd/nand/raw/nand_micron.c | 14 +++++++++++---
> >  1 file changed, 11 insertions(+), 3 deletions(-)
> > 
> > diff --git a/drivers/mtd/nand/raw/nand_micron.c b/drivers/mtd/nand/raw/nand_micron.c
> > index 1622d3145587..fb199ad2f1a6 100644
> > --- a/drivers/mtd/nand/raw/nand_micron.c
> > +++ b/drivers/mtd/nand/raw/nand_micron.c
> > @@ -390,6 +390,14 @@ static int micron_supports_on_die_ecc(struct nand_chip *chip)
> >  	    (chip->id.data[4] & MICRON_ID_INTERNAL_ECC_MASK) != 0x2)
> >  		return MICRON_ON_DIE_UNSUPPORTED;
> >  
> > +	/*
> > +	 * It seems that there are devices which do not support ECC official.
> > +	 * At least the MT29F2G08ABAGA / MT29F2G08ABBGA devices supports
> > +	 * enabling the ECC feature but don't reflect that to the READ_ID table.
> > +	 * So we have to guarantee that we disable the ECC feature directly
> > +	 * after we did the READ_ID table command. Later we can evaluate the
> > +	 * ECC_ENABLE support.
> > +	 */
> >  	ret = micron_nand_on_die_ecc_setup(chip, true);
> >  	if (ret)
> >  		return MICRON_ON_DIE_UNSUPPORTED;
> > @@ -398,13 +406,13 @@ static int micron_supports_on_die_ecc(struct nand_chip *chip)
> >  	if (ret)
> >  		return MICRON_ON_DIE_UNSUPPORTED;
> >  
> > -	if (!(id[4] & MICRON_ID_ECC_ENABLED))
> > -		return MICRON_ON_DIE_UNSUPPORTED;
> > -
> >  	ret = micron_nand_on_die_ecc_setup(chip, false);
> >  	if (ret)
> >  		return MICRON_ON_DIE_UNSUPPORTED;
> >  
> > +	if (!(id[4] & MICRON_ID_ECC_ENABLED))
> > +		return MICRON_ON_DIE_UNSUPPORTED;
> > +
> >  	ret = nand_readid_op(chip, 0, id, sizeof(id));
> >  	if (ret)
> >  		return MICRON_ON_DIE_UNSUPPORTED;
> 
> Thanks,
> Miquèl

______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/