Re: [PATCH v8 3/5] mtd: Add support for HyperBus memory devices

[Sergei Shtylyov <sergei.shtylyov@xxxxxxxxxxxxxxxxxx>]

Hello!

On 07/03/2019 07:41 AM, Vignesh Raghavendra wrote:

>>> Cypress' HyperBus is Low Signal Count, High Performance Double Data Rate
>>> Bus interface between a host system master and one or more slave
>>> interfaces. HyperBus is used to connect microprocessor, microcontroller,
>>> or ASIC devices with random access NOR flash memory (called HyperFlash)
>>> or self refresh DRAM (called HyperRAM).
>>>
>>> Its a 8-bit data bus (DQ[7:0]) with  Read-Write Data Strobe (RWDS)
>>> signal and either Single-ended clock(3.0V parts) or Differential clock
>>> (1.8V parts). It uses ChipSelect lines to select b/w multiple slaves.
>>> At bus level, it follows a separate protocol described in HyperBus
>>> specification[1].
>>>
>>> HyperFlash follows CFI AMD/Fujitsu Extended Command Set (0x0002) similar
>>> to that of existing parallel NORs. Since HyperBus is x8 DDR bus,
>>> its equivalent to x16 parallel NOR flash with respect to bits per clock
>>> cycle. But HyperBus operates at >166MHz frequencies.
>>> HyperRAM provides direct random read/write access to flash memory
>>> array.
>>>
>>> But, HyperBus memory controllers seem to abstract implementation details
>>> and expose a simple MMIO interface to access connected flash.
>>>
>>> Add support for registering HyperFlash devices with MTD framework. MTD
>>> maps framework along with CFI chip support framework are used to support
>>> communicating with flash.
>>>
>>> Framework is modelled along the lines of spi-nor framework. HyperBus
>>> memory controller (HBMC) drivers calls hyperbus_register_device() to
>>> register a single HyperFlash device. HyperFlash core parses MMIO access
>>> information from DT, sets up the map_info struct, probes CFI flash and
>>> registers it with MTD framework.
>>>
>>> Some HBMC masters need calibration/training sequence[3] to be carried
>>> out, in order for DLL inside the controller to lock, by reading a known
>>> string/pattern. This is done by repeatedly reading CFI Query
>>> Identification String. Calibration needs to be done before trying to detect
>>> flash as part of CFI flash probe.
>>>
>>> HyperRAM is not supported at the moment.
>>>
>>> HyperBus specification can be found at[1]
>>> HyperFlash datasheet can be found at[2]
>>>
>>> [1] https://www.cypress.com/file/213356/download
>>> [2] https://www.cypress.com/file/213346/download
>>> [3] http://www.ti.com/lit/ug/spruid7b/spruid7b.pdf
>>>     Table 12-5741. HyperFlash Access Sequence
>>>
>>> Signed-off-by: Vignesh Raghavendra <vigneshr@xxxxxx>
>> [...]
>>
>>    I have at least created my HyperBus driver and unfortunately I'm having serious

   At last. :-)

>> issues with the design of the support core (see below)...
>>
>> [...]
>>> diff --git a/drivers/mtd/hyperbus/hyperbus-core.c b/drivers/mtd/hyperbus/hyperbus-core.c
>>> new file mode 100644
>>> index 000000000000..63a9e64895bc
>>> --- /dev/null
>>> +++ b/drivers/mtd/hyperbus/hyperbus-core.c
>>> @@ -0,0 +1,154 @@
>> [...]
>>> +int hyperbus_register_device(struct hyperbus_device *hbdev)
>>> +{
>>> +	const struct hyperbus_ops *ops;
>>> +	struct hyperbus_ctlr *ctlr;
>>> +	struct device_node *np;
>>> +	struct map_info *map;
>>> +	struct resource res;
>>> +	struct device *dev;
>>> +	int ret;
>>> +
>>> +	if (!hbdev || !hbdev->np || !hbdev->ctlr || !hbdev->ctlr->dev) {
>>> +		pr_err("hyperbus: please fill all the necessary fields!\n");
>>> +		return -EINVAL;
>>> +	}
>>> +
>>> +	np = hbdev->np;
>>> +	ctlr = hbdev->ctlr;
>>> +	if (!of_device_is_compatible(np, "cypress,hyperflash"))
>>> +		return -ENODEV;
>>> +
>>> +	hbdev->memtype = HYPERFLASH;
>>> +
>>> +	ret = of_address_to_resource(np, 0, &res);
>>
>>    Hm, I doubt that the HB devices are wholly mapped into memory space, that seems
>> like a property of the HB controller. In my case, the flash device in the DT has
>> only single-cell "reg" prop (equal to the chip select #). Then this function returns 
>> -EINVAL and the registration fails. Also, in my case such mapping is R/O, not R/W.
>>
> 
> You could declare R/O MMIO region in controla and set up a translation using ranges
> from slave's reg CS based reg mapping like:

   No, not all HB controllers work the same (simple) way as yours. In case of RPC-IF,
the direct read map is a 64 MiB window into a possibly larger flash chip, it has a
register supplying address bits 25:31...

> +	hbmc: hyperbus@47034000 {
> +		compatible = "ti,am654-hbmc";
> +		reg = <0x0 0x47034000 0x0 0x100>,
> +			<0x5 0x00000000 0x1 0x0000000>;
> +		#address-cells = <2>;
> +		#size-cells = <1>;
> +		ranges = <0x0 0x0 0x5 0x00000000 0x4000000>, /* CS0 - 64MB */
> +			 <0x1 0x0 0x5 0x04000000 0x4000000>; /* CS1 - 64MB */
> +
> +		/* Slave flash node */
> +		flash@0,0 {
> +			compatible = "cypress,hyperflash", "cfi-flash";
> +			reg = <0x0 0x0 0x4000000>;
> +		};
> +	};
> 
> If you use just CS# how would you handle CS to MMIO region mapping? 
> Does both CS use the same MMIO base for reads?

   The RPC-IF HF mode only has a single CS signal.

[...]

MBR, Sergei

______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/