Re: [PATCH] mtd: nand: raw: brcmnand: When oops in progress use pio and interrupt polling

[Miquel Raynal <miquel.raynal@xxxxxxxxxxx>]

Hi Kamal,

Kamal Dasu <kdasu.kdev@xxxxxxxxx> wrote on Wed,  1 May 2019 13:46:15
-0400:

> If mtd_oops is in progress switch to polling for nand command completion

s/nand/NAND/

> interrupts and use PIO mode wihtout DMA so that the mtd_oops buffer can
> be completely written in the assinged nand partition.

What about:

"If mtd_oops is in progress, switch to polling during NAND command
completion instead of relying on DMA/interrupts so that the mtd_oops
buffer can be completely written in the assigned NAND partition."

> This is needed in
> cases where the panic does not happen on cpu0 and there is only one online
> CPU and the panic is not on cpu0.

"This is needed in case the panic does not happen on CPU0 and there is
only one online CPU."

I am not sure to understand the problem or how this can happen (and
be a problem). Have you met such issue already or is this purely
speculative?

> 
> Signed-off-by: Kamal Dasu <kdasu.kdev@xxxxxxxxx>
> ---
>  drivers/mtd/nand/raw/brcmnand/brcmnand.c | 55 ++++++++++++++++++++++++++++++--
>  1 file changed, 52 insertions(+), 3 deletions(-)
> 
> diff --git a/drivers/mtd/nand/raw/brcmnand/brcmnand.c b/drivers/mtd/nand/raw/brcmnand/brcmnand.c
> index 482c6f0..cfbe51a 100644
> --- a/drivers/mtd/nand/raw/brcmnand/brcmnand.c
> +++ b/drivers/mtd/nand/raw/brcmnand/brcmnand.c
> @@ -823,6 +823,12 @@ static inline bool has_flash_dma(struct brcmnand_controller *ctrl)
>  	return ctrl->flash_dma_base;
>  }
>  
> +static inline void disable_flash_dma_xfer(struct brcmnand_controller *ctrl)
> +{
> +	if (has_flash_dma(ctrl))
> +		ctrl->flash_dma_base = 0;
> +}
> +
>  static inline bool flash_dma_buf_ok(const void *buf)
>  {
>  	return buf && !is_vmalloc_addr(buf) &&
> @@ -1237,15 +1243,58 @@ static void brcmnand_cmd_ctrl(struct nand_chip *chip, int dat,
>  	/* intentionally left blank */
>  }
>  
> +static bool is_mtd_oops_in_progress(void)
> +{
> +	int i = 0;
> +
> +#ifdef CONFIG_MTD_OOPS
> +	if (oops_in_progress && smp_processor_id()) {
> +		int cpu = 0;
> +
> +		for_each_online_cpu(cpu)
> +			++i;
> +	}
> +#endif
> +	return i == 1 ? true : false;

I suppose return (i == 1); is enough

> +}
> +
> +static bool brcmstb_nand_wait_for_completion(struct nand_chip *chip)
> +{
> +	struct brcmnand_host *host = nand_get_controller_data(chip);
> +	struct brcmnand_controller *ctrl = host->ctrl;
> +	bool err = false;
> +	int sts;
> +
> +	if (is_mtd_oops_in_progress()) {
> +		/* Switch to interrupt polling and PIO mode */
> +		disable_flash_dma_xfer(ctrl);
> +		sts = bcmnand_ctrl_poll_status(ctrl, NAND_CTRL_RDY |
> +					       NAND_STATUS_READY,
> +					       NAND_CTRL_RDY |
> +					       NAND_STATUS_READY, 0);
> +		err = (sts < 0) ? true : false;
> +	} else {
> +		unsigned long timeo = msecs_to_jiffies(
> +						NAND_POLL_STATUS_TIMEOUT_MS);
> +		/* wait for completion interrupt */
> +		sts = wait_for_completion_timeout(&ctrl->done, timeo);
> +		err = (sts <= 0) ? true : false;
> +	}
> +
> +	return err;
> +}
> +
>  static int brcmnand_waitfunc(struct nand_chip *chip)
>  {
>  	struct brcmnand_host *host = nand_get_controller_data(chip);
>  	struct brcmnand_controller *ctrl = host->ctrl;
> -	unsigned long timeo = msecs_to_jiffies(100);
> +	bool err = false;
>  
>  	dev_dbg(ctrl->dev, "wait on native cmd %d\n", ctrl->cmd_pending);
> -	if (ctrl->cmd_pending &&
> -			wait_for_completion_timeout(&ctrl->done, timeo) <= 0) {

What about the wait_for_completion_timeout() call in brcmnand_write()?

> +	if (ctrl->cmd_pending)
> +		err = brcmstb_nand_wait_for_completion(chip);
> +
> +	if (err) {
>  		u32 cmd = brcmnand_read_reg(ctrl, BRCMNAND_CMD_START)
>  					>> brcmnand_cmd_shift(ctrl);  
>  


Thanks,
Miquèl

______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/