On 25.03.2019 23:13, Sergei Shtylyov wrote:
Cypress' Hyperbus is Low Signal Count, High Performance Double Data Rate
It's HyperBus, according to the spec...
Bus interface between a host system master and one or more slave
interfaces. Hyperbus is used to connect microprocessor, microcontroller,
or ASIC devices with random access NOR flash memory (called Hyperflash)
or self refresh DRAM (called HyperRAM).
Its a 8-bit data bus (DQ[7:0]) with Read-Write Data Strobe (RWDS)
signal and either Single-ended clock(3.0V parts) or Differential clock
(1.8V parts). It uses ChipSelect lines to select b/w multiple slaves.
At bus level, it follows a separate protocol described in Hyperbus
specification[1].
HyperBus.
Hyperflash follows CFI AMD/Fujitsu Extended Command Set (0x0002) similar
to that of existing parallel NORs. Since Hyperbus is x8 DDR bus,
its equivalent to x16 parallel NOR flash wrt bits per clock cycle. But
Hyperbus operates at >166MHz frequencies.
HyperRAM provides direct random read/write access to flash memory
array.
But, Hyperbus memory controllers seem to abstract implementation details
HyperBus.
and expose a simple MMIO interface to access connected flash.
Add support for registering Hyperflash devices with MTD framework. MTD
HyperFlash.
maps framework along with CFI chip support framework are used to support
communicating with flash.
Framework is modelled along the lines of spi-nor framework. Hyperbus
HyperBus.
memory controller (HBMC) drivers calls hyperbus_register_device() to
register a single Hyperflash device. Hyperflash core parses MMIO access
HyperFlash.
information from DT, sets up the map_info struct, probes CFI flash and
registers it with MTD framework.
Some HBMC masters need calibration/training sequence[3] to be carried
out, in order for DLL inside the controller to lock, by reading a known
string/pattern. This is done by repeatedly reading CFI Query
Identification String. Calibration needs to be done before trying to detect
flash as part of CFI flash probe.
HyperRAM is not supported at the moment.
Hyperbus specification can be found at[1]
Hyperflash datasheet can be found at[2]
HyperBus & HyperFlash.
[1] https://www.cypress.com/file/213356/download
[2] https://www.cypress.com/file/213346/download
[3] http://www.ti.com/lit/ug/spruid7b/spruid7b.pdf
Table 12-5741. HyperFlash Access Sequence
Signed-off-by: Vignesh Raghavendra <vigneshr@xxxxxx>
[...]
diff --git a/drivers/mtd/hyperbus/hyperbus-core.c b/drivers/mtd/hyperbus/hyperbus-core.c
new file mode 100644
index 000000000000..4c2876c367fc
--- /dev/null
+++ b/drivers/mtd/hyperbus/hyperbus-core.c
@@ -0,0 +1,183 @@
+// SPDX-License-Identifier: GPL-2.0
+//
+// Copyright (C) 2019 Texas Instruments Incorporated - http://www.ti.com/
+// Author: Vignesh Raghavendra <vigneshr@xxxxxx>
+
+#include <linux/err.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/mtd/hyperbus.h>
+#include <linux/mtd/map.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/cfi.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/types.h>
+
+#define HYPERBUS_CALIB_COUNT 25
As I said, this seems platform specific...
[...]
+/* Default calibration routine for use by Hyperbus controller.
No, there should be easy opt-out from the calibration method.
Currently, the driver will have to define its own calibrate method, even
if does't need any calibration...
Nevermind -- the method ptr can be NULL, of course, so there's easy opt-out...
[...]
MBR, Sergei
______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/
