On 20/03/2019 08:33, Tudor.Ambarus@xxxxxxxxxxxxx wrote:
On 03/20/2019 09:06 AM, Jonas Bonn wrote:
External E-Mail
On 20/03/2019 07:33, Tudor.Ambarus@xxxxxxxxxxxxx wrote:
Jonas,
On 03/19/2019 09:13 AM, Jonas Bonn wrote:
On 19/03/2019 07:59, Tudor.Ambarus@xxxxxxxxxxxxx wrote:
Jonas, Yong,
On 03/12/2019 09:27 PM, Yong Qin wrote:
Hi Tudor,
Good question.
The WP# function is not available when the Quad mode is enabled (CR[1]=1). The WP# function is replaced by IO2 for input and output during Quad mode. With that said, if CR[1] is set to 1 (Quad mode enabled), the registers will not be protected.
Technically default SRWD bit can be set as either 0 or 1. However, as most customers (applications) don't use this feature to protect registers, the default SRWD bit set to 0 might be a better choice, and reserve the option to change to 1 for the applications do need this feature.
I think I found the reason why SRWD bit is configurable, and disabled by
default: => to allow the installation of the flash in a system with a grounded
WP# pin while still enabling write to the BP bits.
I think this is bogus. Why would you ground the SRWD pin? That's a design error.
I've talked with Microchip hardware team, we have this feature on sst26 flashes too.
Grounding WP would not necessarily be a design error. The intention is that some
users might choose to populate the Flash chip onto their PCB, program the memory
in-circuit, and then lock down the write protection to use the chip like a ROM.
Grounding WP allows them to do this. Since SRWD is set to '0' from the factory,
so users can program the memory, set the block protection (BP) bits to protect
the memory, and then set the SRWD bit to enable the grounded WP input and
prevent changing the BP bits.
Again, this is bogus. The SRWD bit is non-volatile so just resetting the flash clears the bit and the BP bits can be changed. This does not magically turn the flash into a ROM. Grounded or not, the WP# is NOT respected until the SRWD bit is set; what you've described is yet another reason to default the SRWD to set.
SRWD is a non-volatile bit: default at power-up will be the setting prior to
power-down.
Ah, right you are! :)
By grounding the WP# pin, you are effectively turning the SRWD bit into
an OTP bit. Note that what you described above also requires setting
the BPNV bit, otherwise protection is irrevocably reset to "unprotected"
at reset. The BPNV bit cannot be set from Linux so whoever is using the
"grounded pin" method must be programming the board in-factory from
another system than Linux. Therefore it's OK for Linux to default SRWD
to asserted, irregardless of the state of WP#.
/Jonas
Cheers,
ta
With the BPNV bit (see patch 3 that I posted in the v2 series), at least the flash can be made to start up write-protected; however, there is nothing preventing modification of the PROTection bits until SRWD is set AND WP# is asserted (through grounding or otherwise). Linux currently defaults SRWD to cleared which is "unprotected", irregardless of the state of WP#.
The grounded WP pin + SRWD bit method is an older, legacy approach to the
problem. We don't know how many users actually ground the WP pin in this manner,
but there are probably some users out there who do.
If they do so, they are fooling themselves... or they are running a patched kernel! :)
/Jonas
Cheers,
ta
/Jonas
Jonas, Yong, what do you think?
Cheers,
ta
Thanks,
Yong
-----Original Message-----
From: Tudor.Ambarus@xxxxxxxxxxxxx <Tudor.Ambarus@xxxxxxxxxxxxx>
Sent: Tuesday, March 12, 2019 5:30 AM
To: Yong Qin <Yong.Qin@xxxxxxxxxxx>; jonas@xxxxxxxxxxx; James Tomasetta <James.Tomasetta@xxxxxxxxxxx>
Cc: linux-mtd@xxxxxxxxxxxxxxxxxxx; bbrezillon@xxxxxxxxxx; richard@xxxxxx; marek.vasut@xxxxxxxxx; computersforpeace@xxxxxxxxx; dwmw2@xxxxxxxxxxxxx
Subject: Re: [PATCH v2 1/3] mtd: spi-nor: always respect write-protect input
Hi, Yong,
Thank you for the explanation. There are still few things to clarify.
On 03/11/2019 10:14 PM, Yong Qin wrote:
SRWD bit (along with WP#) provides a way to protect Status and Configuration Registers from been modified unintendedly or by a malicious actor.
By default, SRWD bit is 0, which means no protection on registers alternations. Registers can be modified easily by WRR command. (this is most of the application use cases).
If set SRWD bit to 1, then when WP# is driven low during WRR command, WRR command will be ignored and Registers can't be modified. This provides a way to protect Registers, meanwhile still reserve the capability to modify Registers when necessary by driving WP# to high during WRR command.
Does the SRWD bit protect the Status and Configuration Register bits even when in Quad Mode? WP# function is not available in Quad mode. How can one release this protection when in Quad Mode and SRWD set to 1?
If SRWD bit is ignored in Quad Mode, then why didn't Cypress enable Status and Configuration Register bits protection by default? I.e., remove SRWD bit from SR1, make BIT(7) a NOP, and consider the Status and Configuration Register bits protection enabled by default when not in Quad Mode.
Cheers,
ta
This message and any attachments may contain confidential information from Cypress or its subsidiaries. If it has been received in error, please advise the sender and immediately delete this message.
______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/
______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/
