For a maintainability by reducing the goto statement remove it from do_write_buffer(). Signed-off-by: Tokunori Ikegami <ikegami_to@xxxxxxxxxxx> Cc: Fabio Bettoni <fbettoni@xxxxxxxxx> Co: Hauke Mehrtens <hauke@xxxxxxxxxx> Co: Koen Vandeputte <koen.vandeputte@xxxxxxxxxxxx> Cc: Chris Packham <chris.packham@xxxxxxxxxxxxxxxxxxx> Cc: Joakim Tjernlund <Joakim.Tjernlund@xxxxxxxxxxxx> Cc: Boris Brezillon <boris.brezillon@xxxxxxxxxxxxxxxxxx> Cc: linux-mtd@xxxxxxxxxxxxxxxxxxx --- Changes since v3: - Just change the email address of Tokunori Ikegami to ikegami_to@xxxxxxxxxxx. Changes since v2: - None. Changes since v1: - Split the patch v1 3/3. drivers/mtd/chips/cfi_cmdset_0002.c | 46 +++++++++++++++++++------------------ 1 file changed, 24 insertions(+), 22 deletions(-) diff --git a/drivers/mtd/chips/cfi_cmdset_0002.c b/drivers/mtd/chips/cfi_cmdset_0002.c index ca9d5fa..1aacf22 100755 --- a/drivers/mtd/chips/cfi_cmdset_0002.c +++ b/drivers/mtd/chips/cfi_cmdset_0002.c @@ -1880,38 +1880,40 @@ static int __xipram do_write_buffer(struct map_info *map, struct flchip *chip, if (chip_good(map, adr, datum)) { xip_enable(map, chip, adr); - goto op_done; + break; } - if (time_after(jiffies, timeo)) + if (time_after(jiffies, timeo)) { + ret = -EIO; break; + } /* Latency issues. Drop the lock, wait a while and retry */ UDELAY(map, chip, adr, 1); } - /* - * Recovery from write-buffer programming failures requires - * the write-to-buffer-reset sequence. Since the last part - * of the sequence also works as a normal reset, we can run - * the same commands regardless of why we are here. - * See e.g. - * http://www.spansion.com/Support/Application%20Notes/MirrorBit_Write_Buffer_Prog_Page_Buffer_Read_AN.pdf - */ - cfi_send_gen_cmd(0xAA, cfi->addr_unlock1, chip->start, map, cfi, - cfi->device_type, NULL); - cfi_send_gen_cmd(0x55, cfi->addr_unlock2, chip->start, map, cfi, - cfi->device_type, NULL); - cfi_send_gen_cmd(0xF0, cfi->addr_unlock1, chip->start, map, cfi, - cfi->device_type, NULL); - xip_enable(map, chip, adr); - /* FIXME - should have reset delay before continuing */ + if (ret) { + /* + * Recovery from write-buffer programming failures requires + * the write-to-buffer-reset sequence. Since the last part + * of the sequence also works as a normal reset, we can run + * the same commands regardless of why we are here. + * See e.g. + * http://www.spansion.com/Support/Application%20Notes/MirrorBit_Write_Buffer_Prog_Page_Buffer_Read_AN.pdf + */ + cfi_send_gen_cmd(0xAA, cfi->addr_unlock1, chip->start, map, cfi, + cfi->device_type, NULL); + cfi_send_gen_cmd(0x55, cfi->addr_unlock2, chip->start, map, cfi, + cfi->device_type, NULL); + cfi_send_gen_cmd(0xF0, cfi->addr_unlock1, chip->start, map, cfi, + cfi->device_type, NULL); + xip_enable(map, chip, adr); + /* FIXME - should have reset delay before continuing */ - printk(KERN_WARNING "MTD %s(): software timeout, address:0x%.8lx.\n", - __func__, adr); + printk(KERN_WARNING "MTD %s(): software timeout, address:0x%.8lx.\n", + __func__, adr); + } - ret = -EIO; - op_done: chip->state = FL_READY; DISABLE_VPP(map); put_chip(map, chip, adr); -- 2.11.0 ______________________________________________________ Linux MTD discussion mailing list http://lists.infradead.org/mailman/listinfo/linux-mtd/