Re: [PATCH V2 2/2] mmc: sdhci-msm: Rectify DLL programming sequence for SDCC

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Wed, Dec 18, 2024 at 02:40:57PM +0530, Sachin Gupta wrote:
> With the current DLL sequence stability issues for data
> transfer seen in HS400 and HS200 modes.
> 
> "mmc0: cqhci: error IRQ status: 0x00000000 cmd error -84
> data error 0"
> 
> Rectify the DLL programming sequence as per latest hardware
> programming guide and also incorporate support for HS200 and
> HS400 DLL settings using the device tree.

"foo also bar" usually points out that there should be two separate
commits.

> 
> Signed-off-by: Sachin Gupta <quic_sachgupt@xxxxxxxxxxx>
> Signed-off-by: Bao D. Nguyen <nguyenb@xxxxxxxxxxxxxx>
> Signed-off-by: Sarthak Garg <sartgarg@xxxxxxxxxxxxxx>
> Signed-off-by: Jun Li <liju@xxxxxxxxxxxxxx>

This is very strange and incorrect.

> ---
>  drivers/mmc/host/sdhci-msm.c | 372 +++++++++++++++++++++++++++++++++--
>  1 file changed, 353 insertions(+), 19 deletions(-)
> 
> diff --git a/drivers/mmc/host/sdhci-msm.c b/drivers/mmc/host/sdhci-msm.c
> index 2a5e588779fc..4ecb362f7f2a 100644
> --- a/drivers/mmc/host/sdhci-msm.c
> +++ b/drivers/mmc/host/sdhci-msm.c
> @@ -28,6 +28,7 @@
>  #define CORE_VERSION_MAJOR_SHIFT	28
>  #define CORE_VERSION_MAJOR_MASK		(0xf << CORE_VERSION_MAJOR_SHIFT)
>  #define CORE_VERSION_MINOR_MASK		0xff
> +#define SDHCI_MSM_MIN_V_7FF		0x6e
>  
>  #define CORE_MCI_GENERICS		0x70
>  #define SWITCHABLE_SIGNALING_VOLTAGE	BIT(29)
> @@ -118,7 +119,8 @@
>  #define CORE_PWRSAVE_DLL	BIT(3)
>  
>  #define DDR_CONFIG_POR_VAL	0x80040873
> -
> +#define DLL_CONFIG_3_POR_VAL	0x10
> +#define TCXO_FREQ               19200000

What about the platforms where TCXO has different frequency?

>  
>  #define INVALID_TUNING_PHASE	-1
>  #define SDHCI_MSM_MIN_CLOCK	400000
> @@ -256,6 +258,19 @@ struct sdhci_msm_variant_info {
>  	const struct sdhci_msm_offset *offset;
>  };
>  
> +/*
> + * DLL registers which needs be programmed with HSR settings.
> + * Add any new register only at the end and don't change the
> + * sequence.

Why?

> + */
> +struct sdhci_msm_dll {
> +	u32 dll_config[2];
> +	u32 dll_config_2[2];
> +	u32 dll_config_3[2];
> +	u32 dll_usr_ctl[2];
> +	u32 ddr_config[2];
> +};
> +
>  struct sdhci_msm_host {
>  	struct platform_device *pdev;
>  	void __iomem *core_mem;	/* MSM SDCC mapped address */
> @@ -264,6 +279,7 @@ struct sdhci_msm_host {
>  	struct clk *xo_clk;	/* TCXO clk needed for FLL feature of cm_dll*/
>  	/* core, iface, cal and sleep clocks */
>  	struct clk_bulk_data bulk_clks[4];
> +	struct sdhci_msm_dll dll;
>  #ifdef CONFIG_MMC_CRYPTO
>  	struct qcom_ice *ice;
>  #endif
> @@ -292,6 +308,17 @@ struct sdhci_msm_host {
>  	u32 dll_config;
>  	u32 ddr_config;
>  	bool vqmmc_enabled;
> +	bool artanis_dll;
> +};
> +
> +enum dll_init_context {
> +	DLL_INIT_NORMAL,
> +	DLL_INIT_FROM_CX_COLLAPSE_EXIT,
> +};
> +
> +enum mode {
> +	HS400, // equivalent to SDR104 mode for DLL.
> +	HS200, // equivalent to SDR50 mode for DLL.
>  };
>  
>  static const struct sdhci_msm_offset *sdhci_priv_msm_offset(struct sdhci_host *host)
> @@ -778,6 +805,210 @@ static int msm_init_cm_dll(struct sdhci_host *host)
>  	return 0;
>  }
>  
> +static unsigned int sdhci_msm_get_min_clock(struct sdhci_host *host)
> +{
> +	return SDHCI_MSM_MIN_CLOCK;
> +}

Why??? Why do you need a function to return a static value?

> +
> +static unsigned int sdhci_msm_get_clk_rate(struct sdhci_host *host, u32 req_clk)
> +{
> +	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
> +	struct sdhci_msm_host *msm_host = sdhci_pltfm_priv(pltfm_host);
> +	struct clk *core_clk = msm_host->bulk_clks[0].clk;
> +	unsigned int sup_clk;
> +
> +	if (req_clk < sdhci_msm_get_min_clock(host))
> +		return sdhci_msm_get_min_clock(host);
> +
> +	sup_clk = clk_round_rate(core_clk, clk_get_rate(core_clk));
> +
> +	if (host->clock != msm_host->clk_rate)
> +		sup_clk = sup_clk / 2;
> +
> +	return sup_clk;

Why?

> +}
> +
> +/* Initialize the DLL (Programmable Delay Line) */
> +static int sdhci_msm_configure_dll(struct sdhci_host *host, enum dll_init_context
> +				 init_context, enum mode index)
> +{
> +	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
> +	struct sdhci_msm_host *msm_host = sdhci_pltfm_priv(pltfm_host);
> +	const struct sdhci_msm_offset *msm_offset = msm_host->offset;
> +	struct mmc_host *mmc = host->mmc;
> +	u32 ddr_cfg_offset, core_vendor_spec, config;
> +	void __iomem *ioaddr = host->ioaddr;
> +	unsigned long flags, dll_clock;
> +	int rc = 0, wait_cnt = 50;
> +
> +	dll_clock = sdhci_msm_get_clk_rate(host, host->clock);
> +	spin_lock_irqsave(&host->lock, flags);
> +
> +	core_vendor_spec = readl_relaxed(ioaddr + msm_offset->core_vendor_spec);
> +
> +	/*
> +	 * Always disable PWRSAVE during the DLL power
> +	 * up regardless of its current setting.
> +	 */
> +	core_vendor_spec &= ~CORE_CLK_PWRSAVE;
> +	writel_relaxed(core_vendor_spec, ioaddr + msm_offset->core_vendor_spec);
> +
> +	if (msm_host->use_14lpp_dll_reset) {
> +		/* Disable CK_OUT */
> +		config = readl_relaxed(ioaddr + msm_offset->core_dll_config);
> +		config &= ~CORE_CK_OUT_EN;
> +		writel_relaxed(config, ioaddr + msm_offset->core_dll_config);
> +
> +		/* Disable the DLL clock */
> +		config = readl_relaxed(ioaddr + msm_offset->core_dll_config_2);
> +		config |= CORE_DLL_CLOCK_DISABLE;
> +		writel_relaxed(config, ioaddr + msm_offset->core_dll_config_2);
> +	}
> +
> +	/*
> +	 * Write 1 to DLL_RST bit of DLL_CONFIG register
> +	 * and Write 1 to DLL_PDN bit of DLL_CONFIG register.
> +	 */
> +	config = readl_relaxed(ioaddr + msm_offset->core_dll_config);
> +	config |= (CORE_DLL_RST | CORE_DLL_PDN);
> +	writel_relaxed(config, ioaddr + msm_offset->core_dll_config);
> +
> +	/*
> +	 * Configure DLL_CONFIG_3 and USER_CTRL
> +	 * (Only applicable for 7FF projects).
> +	 */
> +	if (msm_host->core_minor >= SDHCI_MSM_MIN_V_7FF) {
> +		writel_relaxed(msm_host->dll.dll_config_3[index],
> +				ioaddr + msm_offset->core_dll_config_3);
> +		writel_relaxed(msm_host->dll.dll_usr_ctl[index],
> +				ioaddr + msm_offset->core_dll_usr_ctl);
> +	}
> +
> +	/*
> +	 * Set DDR_CONFIG since step 7 is setting TEST_CTRL that can be skipped.
> +	 */
> +	ddr_cfg_offset = msm_host->updated_ddr_cfg ? msm_offset->core_ddr_config
> +					: msm_offset->core_ddr_config_old;
> +
> +	config = msm_host->dll.ddr_config[index];
> +	writel_relaxed(config, ioaddr + ddr_cfg_offset);
> +
> +	/* Set DLL_CONFIG_2 */
> +	if (msm_host->use_14lpp_dll_reset) {
> +		u32 mclk_freq;
> +		int cycle_cnt;
> +
> +		/*
> +		 * Only configure the mclk_freq in normal DLL init
> +		 * context. If the DLL init is coming from
> +		 * CX Collapse Exit context, the host->clock may be zero.
> +		 * The DLL_CONFIG_2 register has already been restored to
> +		 * proper value prior to getting here.
> +		 */
> +		if (init_context == DLL_INIT_NORMAL) {
> +			cycle_cnt = readl_relaxed(ioaddr +
> +					msm_offset->core_dll_config_2)
> +					& CORE_FLL_CYCLE_CNT ? 8 : 4;
> +
> +			mclk_freq = DIV_ROUND_CLOSEST_ULL(dll_clock * cycle_cnt, TCXO_FREQ);
> +
> +			if (dll_clock < 100000000) {
> +				pr_err("%s: %s: Non standard clk freq =%u\n",
> +				mmc_hostname(mmc), __func__, dll_clock);
> +				rc = -EINVAL;
> +				goto out;
> +			}
> +
> +			config = readl_relaxed(ioaddr + msm_offset->core_dll_config_2);
> +			config = (config & ~(0xFF << 10)) | (mclk_freq << 10);

GENMASK, FIELD_PREP?

> +			writel_relaxed(config, ioaddr + msm_offset->core_dll_config_2);
> +		}
> +		/* wait for 5us before enabling DLL clock */
> +		udelay(5);
> +	}
> +
> +	/*
> +	 * Update the lower two bytes of DLL_CONFIG only with
> +	 * HSR values. Since these are the static settings.
> +	 */
> +	config = (readl_relaxed(ioaddr + msm_offset->core_dll_config));
> +	config |= (msm_host->dll.dll_config[index] & 0xffff);
> +	writel_relaxed(config, ioaddr + msm_offset->core_dll_config);
> +
> +	/* Wait for 52us */
> +	spin_unlock_irqrestore(&host->lock, flags);
> +	udelay(60);
> +	spin_lock_irqsave(&host->lock, flags);
> +
> +	/*
> +	 * Write 0 to DLL_RST bit of DLL_CONFIG register
> +	 * and Write 0 to DLL_PDN bit of DLL_CONFIG register.
> +	 */
> +	config &= ~CORE_DLL_RST;
> +	writel_relaxed(config, ioaddr + msm_offset->core_dll_config);
> +
> +	config &= ~CORE_DLL_PDN;
> +	writel_relaxed(config, ioaddr + msm_offset->core_dll_config);
> +	/* Write 1 to DLL_RST bit of DLL_CONFIG register */
> +	config |= CORE_DLL_RST;
> +	writel_relaxed(config, ioaddr + msm_offset->core_dll_config);
> +
> +	/* Write 0 to DLL_RST bit of DLL_CONFIG register */
> +	config &= ~CORE_DLL_RST;
> +	writel_relaxed(config, ioaddr + msm_offset->core_dll_config);
> +
> +	/* Set CORE_DLL_CLOCK_DISABLE to 0 */
> +	if (msm_host->use_14lpp_dll_reset) {
> +		config = readl_relaxed(ioaddr + msm_offset->core_dll_config_2);
> +		config &= ~CORE_DLL_CLOCK_DISABLE;
> +		writel_relaxed(config, ioaddr + msm_offset->core_dll_config_2);
> +	}
> +
> +	/* Set DLL_EN bit to 1. */
> +	config = readl_relaxed(ioaddr + msm_offset->core_dll_config);
> +	config |= CORE_DLL_EN;
> +	writel_relaxed(config, ioaddr + msm_offset->core_dll_config);
> +
> +	/*
> +	 * Wait for 8000 input clock. Here we calculate the
> +	 * delay from fixed clock freq 192MHz, which turns out 42us.
> +	 */
> +	spin_unlock_irqrestore(&host->lock, flags);
> +	udelay(50);
> +	spin_lock_irqsave(&host->lock, flags);
> +
> +	/* Set CK_OUT_EN bit to 1. */
> +	config |= CORE_CK_OUT_EN;
> +	writel_relaxed(config, ioaddr + msm_offset->core_dll_config);
> +
> +	/*
> +	 * Wait until DLL_LOCK bit of DLL_STATUS register
> +	 * becomes '1'.
> +	 */
> +	while (!(readl_relaxed(ioaddr + msm_offset->core_dll_status) &
> +		 CORE_DLL_LOCK)) {
> +		/* max. wait for 50us sec for LOCK bit to be set */
> +		if (--wait_cnt == 0) {
> +			dev_err(mmc_dev(mmc), "%s: DLL failed to LOCK\n",
> +			       mmc_hostname(mmc));
> +			rc = -ETIMEDOUT;
> +			goto out;
> +		}
> +		/* wait for 1us before polling again */
> +		udelay(1);
> +	}
> +
> +out:
> +	if (core_vendor_spec & CORE_CLK_PWRSAVE) {
> +		/* Reenable PWRSAVE as needed */
> +		config = readl_relaxed(ioaddr + msm_offset->core_vendor_spec);
> +		config |= CORE_CLK_PWRSAVE;
> +		writel_relaxed(config, ioaddr + msm_offset->core_vendor_spec);
> +	}
> +	spin_unlock_irqrestore(&host->lock, flags);
> +	return rc;
> +}
> +
>  static void msm_hc_select_default(struct sdhci_host *host)
>  {
>  	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
> @@ -900,14 +1131,35 @@ static void sdhci_msm_hc_select_mode(struct sdhci_host *host)
>  		msm_hc_select_default(host);
>  }
>  
> +static int sdhci_msm_init_dll(struct sdhci_host *host, enum dll_init_context init_context)
> +{
> +	unsigned char timing = host->mmc->ios.timing;
> +	int ret;
> +
> +	if (timing == MMC_TIMING_UHS_SDR104 || timing == MMC_TIMING_MMC_HS400)
> +		ret = sdhci_msm_configure_dll(host, DLL_INIT_NORMAL, HS400);
> +	else
> +		ret = sdhci_msm_configure_dll(host, DLL_INIT_NORMAL, HS200);
> +
> +	return ret;
> +}
> +
> +static int sdhci_msm_dll_config(struct sdhci_host *host, enum dll_init_context init_context)
> +{
> +	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
> +	struct sdhci_msm_host *msm_host = sdhci_pltfm_priv(pltfm_host);
> +
> +	return msm_host->artanis_dll ? sdhci_msm_init_dll(host, init_context) :
> +		msm_init_cm_dll(host);
> +}
> +
>  static int sdhci_msm_cdclp533_calibration(struct sdhci_host *host)
>  {
>  	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
>  	struct sdhci_msm_host *msm_host = sdhci_pltfm_priv(pltfm_host);
> +	const struct sdhci_msm_offset *msm_offset = msm_host->offset;
>  	u32 config, calib_done;
>  	int ret;
> -	const struct sdhci_msm_offset *msm_offset =
> -					msm_host->offset;
>  
>  	pr_debug("%s: %s: Enter\n", mmc_hostname(host->mmc), __func__);
>  
> @@ -915,7 +1167,7 @@ static int sdhci_msm_cdclp533_calibration(struct sdhci_host *host)
>  	 * Retuning in HS400 (DDR mode) will fail, just reset the
>  	 * tuning block and restore the saved tuning phase.
>  	 */
> -	ret = msm_init_cm_dll(host);
> +	ret = sdhci_msm_dll_config(host, DLL_INIT_NORMAL);
>  	if (ret)
>  		goto out;
>  
> @@ -1003,7 +1255,7 @@ static int sdhci_msm_cdclp533_calibration(struct sdhci_host *host)
>  	return ret;
>  }
>  
> -static int sdhci_msm_cm_dll_sdc4_calibration(struct sdhci_host *host)
> +static int sdhci_msm_cm_dll_sdc4_calibration(struct sdhci_host *host, enum mode index)
>  {
>  	struct mmc_host *mmc = host->mmc;
>  	u32 dll_status, config, ddr_cfg_offset;
> @@ -1014,7 +1266,6 @@ static int sdhci_msm_cm_dll_sdc4_calibration(struct sdhci_host *host)
>  					sdhci_priv_msm_offset(host);
>  
>  	pr_debug("%s: %s: Enter\n", mmc_hostname(host->mmc), __func__);
> -

Unrelated, please drop.

>  	/*
>  	 * Currently the core_ddr_config register defaults to desired
>  	 * configuration on reset. Currently reprogramming the power on
> @@ -1026,7 +1277,11 @@ static int sdhci_msm_cm_dll_sdc4_calibration(struct sdhci_host *host)
>  		ddr_cfg_offset = msm_offset->core_ddr_config;
>  	else
>  		ddr_cfg_offset = msm_offset->core_ddr_config_old;
> -	writel_relaxed(msm_host->ddr_config, host->ioaddr + ddr_cfg_offset);
> +
> +	if (msm_host->artanis_dll)
> +		writel_relaxed(msm_host->dll.ddr_config[index], host->ioaddr + ddr_cfg_offset);
> +	else
> +		writel_relaxed(msm_host->ddr_config, host->ioaddr + ddr_cfg_offset);
>  
>  	if (mmc->ios.enhanced_strobe) {
>  		config = readl_relaxed(host->ioaddr +
> @@ -1083,11 +1338,10 @@ static int sdhci_msm_hs400_dll_calibration(struct sdhci_host *host)
>  {
>  	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
>  	struct sdhci_msm_host *msm_host = sdhci_pltfm_priv(pltfm_host);
> +	const struct sdhci_msm_offset *msm_offset = msm_host->offset;
>  	struct mmc_host *mmc = host->mmc;
> -	int ret;
>  	u32 config;
> -	const struct sdhci_msm_offset *msm_offset =
> -					msm_host->offset;
> +	int ret;
>  
>  	pr_debug("%s: %s: Enter\n", mmc_hostname(host->mmc), __func__);
>  
> @@ -1095,7 +1349,8 @@ static int sdhci_msm_hs400_dll_calibration(struct sdhci_host *host)
>  	 * Retuning in HS400 (DDR mode) will fail, just reset the
>  	 * tuning block and restore the saved tuning phase.
>  	 */
> -	ret = msm_init_cm_dll(host);
> +	ret = sdhci_msm_dll_config(host, DLL_INIT_NORMAL);
> +
>  	if (ret)
>  		goto out;
>  
> @@ -1115,7 +1370,7 @@ static int sdhci_msm_hs400_dll_calibration(struct sdhci_host *host)
>  	if (msm_host->use_cdclp533)
>  		ret = sdhci_msm_cdclp533_calibration(host);
>  	else
> -		ret = sdhci_msm_cm_dll_sdc4_calibration(host);
> +		ret = sdhci_msm_cm_dll_sdc4_calibration(host, HS400);
>  out:
>  	pr_debug("%s: %s: Exit, ret %d\n", mmc_hostname(host->mmc),
>  		 __func__, ret);
> @@ -1154,7 +1409,8 @@ static int sdhci_msm_restore_sdr_dll_config(struct sdhci_host *host)
>  		return 0;
>  
>  	/* Reset the tuning block */
> -	ret = msm_init_cm_dll(host);
> +	ret = sdhci_msm_dll_config(host, DLL_INIT_NORMAL);
> +
>  	if (ret)
>  		return ret;
>  
> @@ -1223,7 +1479,7 @@ static int sdhci_msm_execute_tuning(struct mmc_host *mmc, u32 opcode)
>  
>  retry:
>  	/* First of all reset the tuning block */
> -	rc = msm_init_cm_dll(host);
> +	rc = sdhci_msm_dll_config(host, DLL_INIT_NORMAL);
>  	if (rc)
>  		return rc;
>  
> @@ -1752,11 +2008,6 @@ static unsigned int sdhci_msm_get_max_clock(struct sdhci_host *host)
>  	return clk_round_rate(core_clk, ULONG_MAX);
>  }
>  
> -static unsigned int sdhci_msm_get_min_clock(struct sdhci_host *host)
> -{
> -	return SDHCI_MSM_MIN_CLOCK;
> -}
> -
>  /*
>   * __sdhci_msm_set_clock - sdhci_msm clock control.
>   *
> @@ -2400,6 +2651,86 @@ static int sdhci_msm_gcc_reset(struct device *dev, struct sdhci_host *host)
>  	return ret;
>  }
>  
> +static int sdhci_msm_dt_get_array(struct device *dev, const char *prop_name,
> +					u32 **bw_vecs, int *len, u32 size)
> +{
> +	struct device_node *np = dev->of_node;
> +	u32 *arr = NULL;
> +	int ret = 0;
> +	size_t sz;
> +
> +	if (!np) {
> +		ret = -ENODEV;
> +		goto out;
> +	}
> +	if (!of_get_property(np, prop_name, len)) {
> +		ret = -EINVAL;
> +		goto out;
> +	}
> +	sz = *len = *len / sizeof(*arr);

You obviously skipped checkpatch run. Please don't do that.

> +	if (sz <= 0 || (size > 0 && (sz > size))) {
> +		dev_err(dev, "%s invalid size\n", prop_name);
> +		ret = -EINVAL;
> +		goto out;
> +	}
> +
> +	arr = devm_kzalloc(dev, sz * sizeof(*arr), GFP_KERNEL);
> +	if (!arr) {
> +		ret = -ENOMEM;
> +		goto out;
> +	}
> +
> +	ret = of_property_read_u32_array(np, prop_name, arr, sz);
> +	if (ret < 0) {
> +		dev_err(dev, "%s failed reading array %d\n", prop_name, ret);
> +		goto out;
> +	}
> +	*bw_vecs = arr;
> +out:
> +	if (ret)
> +		*len = 0;
> +	return ret;
> +}
> +
> +static int sdhci_msm_dt_parse_dll_info(struct device *dev, struct sdhci_msm_host *msm_host)
> +{
> +	int dll_table_len, dll_reg_count;
> +	u32 *dll_table = NULL;
> +	u32 dll_values[10];
> +	int ret = 0, i;
> +
> +	if (sdhci_msm_dt_get_array(dev, "qcom,dll-hsr-list",
> +		&dll_table, &dll_table_len, 0))
> +		goto skip_dll;

Missing update for the bindings.

> +
> +	dll_reg_count = sizeof(struct sdhci_msm_dll) / sizeof(u32);
> +
> +	if (dll_table_len != dll_reg_count) {
> +		dev_err(dev, "Number of HSR entries are not matching\n");
> +		ret = -EINVAL;
> +		goto skip_dll;
> +	}
> +
> +	for (i = 0; i < 5; i++) {

Magic value 5, replace with ARRAY_SIZE

> +		dll_values[2 * i] = dll_table[i];
> +		dll_values[2 * i + 1] = dll_table[i + 5];
> +	}
> +
> +	for (i = 0; i < 10; i++)
> +		dll_table[i] = dll_values[i];

So three memory copies to rearrange the order of values? That sounds
like a horrible solution.

> +
> +	memcpy(&msm_host->dll, dll_table, sizeof(struct sdhci_msm_dll));
> +	msm_host->artanis_dll = true;
> +
> +skip_dll:
> +	if (!dll_table) {
> +		msm_host->artanis_dll = false;
> +		dev_err(dev, "Failed to get dll hsr settings from dt\n");
> +	}
> +
> +	return ret;
> +}
> +
>  static int sdhci_msm_probe(struct platform_device *pdev)
>  {
>  	struct sdhci_host *host;
> @@ -2446,6 +2777,9 @@ static int sdhci_msm_probe(struct platform_device *pdev)
>  
>  	msm_host->saved_tuning_phase = INVALID_TUNING_PHASE;
>  
> +	if (sdhci_msm_dt_parse_dll_info(&pdev->dev, msm_host))
> +		goto pltfm_free;
> +
>  	ret = sdhci_msm_gcc_reset(&pdev->dev, host);
>  	if (ret)
>  		goto pltfm_free;
> -- 
> 2.17.1
> 

-- 
With best wishes
Dmitry




[Index of Archives]     [Linux Memonry Technology]     [Linux USB Devel]     [Linux Media]     [Video for Linux]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]

  Powered by Linux