On 7/11/24 10:05, Sarthak Garg wrote:
> For Qualcomm SoCs with level shifter delays are seen on receivers data
> path due to latency added by level shifter.
>
> To bring these delays in normal range and avoid CMD CRC errors
> reduce frequency for HS mode SD cards to 37.5MHz for targets which has
> level shifter.
>
> Signed-off-by: Sarthak Garg <quic_sartgarg@xxxxxxxxxxx>
> ---
> drivers/mmc/host/sdhci-msm.c | 10 ++++++++++
> 1 file changed, 10 insertions(+)
>
> diff --git a/drivers/mmc/host/sdhci-msm.c b/drivers/mmc/host/sdhci-msm.c
> index 16325c21de52..5e1dc06c4707 100644
> --- a/drivers/mmc/host/sdhci-msm.c
> +++ b/drivers/mmc/host/sdhci-msm.c
> @@ -138,6 +138,8 @@
> /* Max load for eMMC Vdd-io supply */
> #define MMC_VQMMC_MAX_LOAD_UA 325000
>
> +#define LEVEL_SHIFTER_HIGH_SPEED_FREQ 37500000
> +
> #define msm_host_readl(msm_host, host, offset) \
> msm_host->var_ops->msm_readl_relaxed(host, offset)
>
> @@ -287,6 +289,7 @@ struct sdhci_msm_host {
> bool use_cdr;
> u32 transfer_mode;
> bool updated_ddr_cfg;
> + bool uses_level_shifter;
> bool uses_tassadar_dll;
> u32 dll_config;
> u32 ddr_config;
> @@ -366,6 +369,11 @@ static void msm_set_clock_rate_for_bus_mode(struct sdhci_host *host,
>
> mult = msm_get_clock_mult_for_bus_mode(host);
> desired_rate = clock * mult;
> +
> + if (curr_ios.timing == MMC_TIMING_SD_HS && desired_rate == 50000000
Wouldn't desired_rate > LEVEL_SHIFTER_HIGH_SPEED_FREQ make more sense?
> + && msm_host->uses_level_shifter)
> + desired_rate = LEVEL_SHIFTER_HIGH_SPEED_FREQ;
As checkpatch says:
CHECK: Logical continuations should be on the previous line
#46: FILE: drivers/mmc/host/sdhci-msm.c:374:
+ if (curr_ios.timing == MMC_TIMING_SD_HS && desired_rate == 50000000
+ && msm_host->uses_level_shifter)
total: 0 errors, 0 warnings, 1 checks, 34 lines checked
> +
> rc = dev_pm_opp_set_rate(mmc_dev(host->mmc), desired_rate);
> if (rc) {
> pr_err("%s: Failed to set clock at rate %u at timing %d\n",
> @@ -2372,6 +2380,8 @@ static inline void sdhci_msm_get_of_property(struct platform_device *pdev,
>
> of_property_read_u32(node, "qcom,dll-config", &msm_host->dll_config);
>
> + msm_host->uses_level_shifter = of_property_read_bool(node, "qcom,use-level-shifter");
> +
> if (of_device_is_compatible(node, "qcom,msm8916-sdhci"))
> host->quirks2 |= SDHCI_QUIRK2_BROKEN_64_BIT_DMA;
> }
