From: Victor Shih <victor.shih@xxxxxxxxxxxxxxxxxxx>
Changes are:
* Disable GL9755 overcurrent interrupt when power on/off on UHS-II.
* Enable the internal clock when do reset on UHS-II mode.
* Increase timeout value before detecting UHS-II interface.
* Add vendor settings fro UHS-II mode.
* Remove sdhci_gli_enable_internal_clock functon unused clk_ctrl variable.
* Make a function sdhci_gli_wait_software_reset_done() for gl9755 reset.
Signed-off-by: Ben Chuang <ben.chuang@xxxxxxxxxxxxxxxxxxx>
Signed-off-by: AKASHI Takahiro <takahiro.akashi@xxxxxxxxxx>
Signed-off-by: Victor Shih <victor.shih@xxxxxxxxxxxxxxxxxxx>
Signed-off-by: Lucas Lai <lucas.lai@xxxxxxxxxxxxxxxxxxx>
---
Updates in V20:
- Remove sdhci_gli_enable_internal_clock functon unused clk_ctrl variable.
- Make a function sdhci_gli_wait_software_reset_done() for gl9755 reset.
Updates in V19:
- Add sdhci_gli_enable_internal_clock() to simplify the code
in the sdhci_gl9755_reset().
Updates in V17:
- Rname gl9755_overcurrent_event_enable() to
sdhci_gli_overcurrent_event_enable().
Updates in V15:
- Adjust gl9755_vendor_init() to the correct function.
Updates in V13:
- Ues uhs2_sd_tran to stead MMC_UHS2_SD_TRAN.
Updates in V9:
- Rename gl9755_pre_detect_init() to sdhci_gli_pre_detect_init().
- Rename gl9755_uhs2_reset_sd_tran() to sdhci_gli_uhs2_reset_sd_tran().
Updates in V8:
- Use sdhci_get_vdd_value() to simplify code in gl9755_set_power().
- Use read_poll_timeout_atomic() to simplify code in
sdhci_wait_clock_stable().
- Use read_poll_timeout_atomic() to simplify code in sdhci_gl9755_reset().
Updates in V7:
- Drop using gl9755_post_attach_sd().
---
drivers/mmc/host/sdhci-pci-gli.c | 236 ++++++++++++++++++++++++++++++-
1 file changed, 235 insertions(+), 1 deletion(-)
diff --git a/drivers/mmc/host/sdhci-pci-gli.c b/drivers/mmc/host/sdhci-pci-gli.c
index 0f81586a19df..7cf27a666f34 100644
--- a/drivers/mmc/host/sdhci-pci-gli.c
+++ b/drivers/mmc/host/sdhci-pci-gli.c
@@ -18,6 +18,7 @@
#include "sdhci-cqhci.h"
#include "sdhci-pci.h"
#include "cqhci.h"
+#include "sdhci-uhs2.h"
/* Genesys Logic extra registers */
#define SDHCI_GLI_9750_WT 0x800
@@ -139,9 +140,36 @@
#define PCI_GLI_9755_PLLSSC 0x68
#define PCI_GLI_9755_PLLSSC_PPM GENMASK(15, 0)
+#define PCI_GLI_9755_PLLSSC_RTL BIT(24)
+#define GLI_9755_PLLSSC_RTL_VALUE 0x1
+#define PCI_GLI_9755_PLLSSC_TRANS_PASS BIT(27)
+#define GLI_9755_PLLSSC_TRANS_PASS_VALUE 0x1
+#define PCI_GLI_9755_PLLSSC_RECV GENMASK(29, 28)
+#define GLI_9755_PLLSSC_RECV_VALUE 0x0
+#define PCI_GLI_9755_PLLSSC_TRAN GENMASK(31, 30)
+#define GLI_9755_PLLSSC_TRAN_VALUE 0x3
+
+#define PCI_GLI_9755_UHS2_PLL 0x6C
+#define PCI_GLI_9755_UHS2_PLL_SSC GENMASK(9, 8)
+#define GLI_9755_UHS2_PLL_SSC_VALUE 0x0
+#define PCI_GLI_9755_UHS2_PLL_DELAY BIT(18)
+#define GLI_9755_UHS2_PLL_DELAY_VALUE 0x1
+#define PCI_GLI_9755_UHS2_PLL_PDRST BIT(27)
+#define GLI_9755_UHS2_PLL_PDRST_VALUE 0x1
#define PCI_GLI_9755_SerDes 0x70
+#define PCI_GLI_9755_UHS2_SERDES_INTR GENMASK(2, 0)
+#define GLI_9755_UHS2_SERDES_INTR_VALUE 0x3
+#define PCI_GLI_9755_UHS2_SERDES_ZC1 BIT(3)
+#define GLI_9755_UHS2_SERDES_ZC1_VALUE 0x0
+#define PCI_GLI_9755_UHS2_SERDES_ZC2 GENMASK(7, 4)
+#define GLI_9755_UHS2_SERDES_ZC2_DEFAULT 0xB
+#define GLI_9755_UHS2_SERDES_ZC2_SANDISK 0x0
#define PCI_GLI_9755_SCP_DIS BIT(19)
+#define PCI_GLI_9755_UHS2_SERDES_TRAN GENMASK(27, 24)
+#define GLI_9755_UHS2_SERDES_TRAN_VALUE 0xC
+#define PCI_GLI_9755_UHS2_SERDES_RECV GENMASK(31, 28)
+#define GLI_9755_UHS2_SERDES_RECV_VALUE 0xF
#define PCI_GLI_9755_MISC 0x78
#define PCI_GLI_9755_MISC_SSC_OFF BIT(26)
@@ -779,6 +807,204 @@ static void gl9755_hw_setting(struct sdhci_pci_slot *slot)
gl9755_wt_off(pdev);
}
+static void gl9755_vendor_init(struct sdhci_host *host)
+{
+ struct sdhci_pci_slot *slot = sdhci_priv(host);
+ struct pci_dev *pdev = slot->chip->pdev;
+ u32 serdes;
+ u32 pllssc;
+ u32 uhs2_pll;
+
+ gl9755_wt_on(pdev);
+
+ pci_read_config_dword(pdev, PCI_GLI_9755_SerDes, &serdes);
+ serdes &= ~PCI_GLI_9755_UHS2_SERDES_TRAN;
+ serdes |= FIELD_PREP(PCI_GLI_9755_UHS2_SERDES_TRAN,
+ GLI_9755_UHS2_SERDES_TRAN_VALUE);
+ serdes &= ~PCI_GLI_9755_UHS2_SERDES_RECV;
+ serdes |= FIELD_PREP(PCI_GLI_9755_UHS2_SERDES_RECV,
+ GLI_9755_UHS2_SERDES_RECV_VALUE);
+ serdes &= ~PCI_GLI_9755_UHS2_SERDES_INTR;
+ serdes |= FIELD_PREP(PCI_GLI_9755_UHS2_SERDES_INTR,
+ GLI_9755_UHS2_SERDES_INTR_VALUE);
+ serdes &= ~PCI_GLI_9755_UHS2_SERDES_ZC1;
+ serdes |= FIELD_PREP(PCI_GLI_9755_UHS2_SERDES_ZC1,
+ GLI_9755_UHS2_SERDES_ZC1_VALUE);
+ serdes &= ~PCI_GLI_9755_UHS2_SERDES_ZC2;
+ serdes |= FIELD_PREP(PCI_GLI_9755_UHS2_SERDES_ZC2,
+ GLI_9755_UHS2_SERDES_ZC2_DEFAULT);
+ pci_write_config_dword(pdev, PCI_GLI_9755_SerDes, serdes);
+
+ pci_read_config_dword(pdev, PCI_GLI_9755_UHS2_PLL, &uhs2_pll);
+ uhs2_pll &= ~PCI_GLI_9755_UHS2_PLL_SSC;
+ uhs2_pll |= FIELD_PREP(PCI_GLI_9755_UHS2_PLL_SSC,
+ GLI_9755_UHS2_PLL_SSC_VALUE);
+ uhs2_pll &= ~PCI_GLI_9755_UHS2_PLL_DELAY;
+ uhs2_pll |= FIELD_PREP(PCI_GLI_9755_UHS2_PLL_DELAY,
+ GLI_9755_UHS2_PLL_DELAY_VALUE);
+ uhs2_pll &= ~PCI_GLI_9755_UHS2_PLL_PDRST;
+ uhs2_pll |= FIELD_PREP(PCI_GLI_9755_UHS2_PLL_PDRST,
+ GLI_9755_UHS2_PLL_PDRST_VALUE);
+ pci_write_config_dword(pdev, PCI_GLI_9755_UHS2_PLL, uhs2_pll);
+
+ pci_read_config_dword(pdev, PCI_GLI_9755_PLLSSC, &pllssc);
+ pllssc &= ~PCI_GLI_9755_PLLSSC_RTL;
+ pllssc |= FIELD_PREP(PCI_GLI_9755_PLLSSC_RTL,
+ GLI_9755_PLLSSC_RTL_VALUE);
+ pllssc &= ~PCI_GLI_9755_PLLSSC_TRANS_PASS;
+ pllssc |= FIELD_PREP(PCI_GLI_9755_PLLSSC_TRANS_PASS,
+ GLI_9755_PLLSSC_TRANS_PASS_VALUE);
+ pllssc &= ~PCI_GLI_9755_PLLSSC_RECV;
+ pllssc |= FIELD_PREP(PCI_GLI_9755_PLLSSC_RECV,
+ GLI_9755_PLLSSC_RECV_VALUE);
+ pllssc &= ~PCI_GLI_9755_PLLSSC_TRAN;
+ pllssc |= FIELD_PREP(PCI_GLI_9755_PLLSSC_TRAN,
+ GLI_9755_PLLSSC_TRAN_VALUE);
+ pci_write_config_dword(pdev, PCI_GLI_9755_PLLSSC, pllssc);
+
+ gl9755_wt_off(pdev);
+}
+
+static void sdhci_gli_pre_detect_init(struct sdhci_host *host)
+{
+ /* Need more time on UHS2 detect flow */
+ sdhci_writeb(host, 0xA7, SDHCI_UHS2_TIMER_CTRL);
+}
+
+static void sdhci_gli_overcurrent_event_enable(struct sdhci_host *host, bool enable)
+{
+ u32 mask;
+
+ mask = sdhci_readl(host, SDHCI_SIGNAL_ENABLE);
+ if (enable)
+ mask |= SDHCI_INT_BUS_POWER;
+ else
+ mask &= ~SDHCI_INT_BUS_POWER;
+
+ sdhci_writel(host, mask, SDHCI_SIGNAL_ENABLE);
+
+ mask = sdhci_readl(host, SDHCI_INT_ENABLE);
+ if (enable)
+ mask |= SDHCI_INT_BUS_POWER;
+ else
+ mask &= ~SDHCI_INT_BUS_POWER;
+
+ sdhci_writel(host, mask, SDHCI_INT_ENABLE);
+}
+
+static void gl9755_set_power(struct sdhci_host *host, unsigned char mode,
+ unsigned short vdd)
+{
+ u8 pwr = 0;
+
+ if (mode != MMC_POWER_OFF) {
+ pwr = sdhci_get_vdd_value(vdd);
+ if (!pwr)
+ WARN(1, "%s: Invalid vdd %#x\n", mmc_hostname(host->mmc), vdd);
+ pwr |= SDHCI_VDD2_POWER_180;
+ }
+
+ if (host->pwr == pwr)
+ return;
+
+ host->pwr = pwr;
+
+ if (pwr == 0) {
+ sdhci_gli_overcurrent_event_enable(host, false);
+ sdhci_writeb(host, 0, SDHCI_POWER_CONTROL);
+ } else {
+ sdhci_gli_overcurrent_event_enable(host, false);
+ sdhci_writeb(host, 0, SDHCI_POWER_CONTROL);
+
+ pwr |= (SDHCI_POWER_ON | SDHCI_VDD2_POWER_ON);
+
+ sdhci_writeb(host, pwr & 0xf, SDHCI_POWER_CONTROL);
+ /* wait stable */
+ mdelay(5);
+ sdhci_writeb(host, pwr, SDHCI_POWER_CONTROL);
+ /* wait stable */
+ mdelay(5);
+ sdhci_gli_overcurrent_event_enable(host, true);
+ }
+}
+
+static bool sdhci_wait_clock_stable(struct sdhci_host *host)
+{
+ u16 clk = 0;
+
+ if (read_poll_timeout_atomic(sdhci_readw, clk, (clk & SDHCI_CLOCK_INT_STABLE),
+ 10, 20000, false, host, SDHCI_CLOCK_CONTROL)) {
+ pr_err("%s: Internal clock never stabilised.\n", mmc_hostname(host->mmc));
+ sdhci_dumpregs(host);
+ return false;
+ }
+ return true;
+}
+
+static void sdhci_gli_enable_internal_clock(struct sdhci_host *host)
+{
+ u16 ctrl2;
+
+ ctrl2 = sdhci_readw(host, SDHCI_HOST_CONTROL2);
+
+ sdhci_writew(host, SDHCI_CLOCK_INT_EN, SDHCI_CLOCK_CONTROL);
+
+ if (!((ctrl2 & SDHCI_CTRL_V4_MODE) &&
+ (ctrl2 & SDHCI_CTRL_UHS2_ENABLE))) {
+ sdhci_wait_clock_stable(host);
+ sdhci_writew(host, SDHCI_CTRL_V4_MODE, SDHCI_HOST_CONTROL2);
+ }
+}
+
+static int sdhci_gli_wait_software_reset_done(struct sdhci_host *host, u8 mask)
+{
+ u8 rst;
+
+ /* hw clears the bit when it's done */
+ if (read_poll_timeout_atomic(sdhci_readb, rst, !(rst & mask),
+ 10, 100000, false, host, SDHCI_SOFTWARE_RESET)) {
+ pr_err("%s: Reset 0x%x never completed.\n", mmc_hostname(host->mmc), (int)mask);
+ sdhci_dumpregs(host);
+ /* manual clear */
+ sdhci_writeb(host, 0, SDHCI_SOFTWARE_RESET);
+ return -ETIMEDOUT;
+ }
+
+ return 0;
+}
+
+static void sdhci_gli_uhs2_reset_sd_tran(struct sdhci_host *host)
+{
+ /* do this on UHS2 mode */
+ if (host->mmc->uhs2_sd_tran) {
+ sdhci_uhs2_reset(host, SDHCI_UHS2_SW_RESET_SD);
+ sdhci_writel(host, host->ier, SDHCI_INT_ENABLE);
+ sdhci_writel(host, host->ier, SDHCI_SIGNAL_ENABLE);
+ sdhci_uhs2_clear_set_irqs(host,
+ SDHCI_INT_ALL_MASK,
+ SDHCI_UHS2_INT_ERROR_MASK);
+ }
+}
+
+static void sdhci_gl9755_reset(struct sdhci_host *host, u8 mask)
+{
+ /* need internal clock */
+ if (mask & SDHCI_RESET_ALL)
+ sdhci_gli_enable_internal_clock(host);
+
+ sdhci_writeb(host, mask, SDHCI_SOFTWARE_RESET);
+
+ /* reset sd-tran on UHS2 mode if need to reset cmd/data */
+ if ((mask & SDHCI_RESET_CMD) | (mask & SDHCI_RESET_DATA))
+ sdhci_gli_uhs2_reset_sd_tran(host);
+
+ if (mask & SDHCI_RESET_ALL)
+ host->clock = 0;
+
+ if (sdhci_gli_wait_software_reset_done(host, mask))
+ return;
+}
+
static inline void gl9767_vhs_read(struct pci_dev *pdev)
{
u32 vhs_enable;
@@ -1086,6 +1312,7 @@ static int gli_probe_slot_gl9755(struct sdhci_pci_slot *slot)
gli_pcie_enable_msi(slot);
slot->host->mmc->caps2 |= MMC_CAP2_NO_SDIO;
sdhci_enable_v4_mode(host);
+ gl9755_vendor_init(host);
return 0;
}
@@ -1524,17 +1751,24 @@ static const struct sdhci_ops sdhci_gl9755_ops = {
.read_w = sdhci_gli_readw,
.read_b = sdhci_gli_readb,
.set_clock = sdhci_gl9755_set_clock,
+ .set_power = gl9755_set_power,
.enable_dma = sdhci_pci_enable_dma,
.set_bus_width = sdhci_set_bus_width,
- .reset = sdhci_reset,
+ .reset = sdhci_gl9755_reset,
.set_uhs_signaling = sdhci_set_uhs_signaling,
.voltage_switch = sdhci_gli_voltage_switch,
+ .dump_uhs2_regs = sdhci_uhs2_dump_regs,
+ .set_timeout = sdhci_uhs2_set_timeout,
+ .irq = sdhci_uhs2_irq,
+ .uhs2_pre_detect_init = sdhci_gli_pre_detect_init,
};
const struct sdhci_pci_fixes sdhci_gl9755 = {
.quirks = SDHCI_QUIRK_NO_ENDATTR_IN_NOPDESC,
.quirks2 = SDHCI_QUIRK2_BROKEN_DDR50,
.probe_slot = gli_probe_slot_gl9755,
+ .add_host = sdhci_pci_uhs2_add_host,
+ .remove_host = sdhci_pci_uhs2_remove_host,
.ops = &sdhci_gl9755_ops,
#ifdef CONFIG_PM_SLEEP
.resume = sdhci_pci_gli_resume,
--
2.25.1
