Hi Andrea,
i think the following subject would be better:
arm64: dts: broadcom: Add minimal support for Raspberry Pi 5
because you also add the board file here.
Am 28.05.24 um 15:32 schrieb Andrea della Porta:
The BCM2712 SoC family can be found on Raspberry Pi 5.
Add minimal SoC and board (Rpi5 specific) dts file to be able to
boot from SD card and use console on debug UART.
Signed-off-by: Andrea della Porta <andrea.porta@xxxxxxxx>
---
arch/arm64/boot/dts/broadcom/Makefile | 1 +
.../boot/dts/broadcom/bcm2712-rpi-5-b.dts | 64 ++++
arch/arm64/boot/dts/broadcom/bcm2712.dtsi | 292 ++++++++++++++++++
3 files changed, 357 insertions(+)
create mode 100644 arch/arm64/boot/dts/broadcom/bcm2712-rpi-5-b.dts
create mode 100644 arch/arm64/boot/dts/broadcom/bcm2712.dtsi
diff --git a/arch/arm64/boot/dts/broadcom/Makefile b/arch/arm64/boot/dts/broadcom/Makefile
index 8b4591ddd27c..92565e9781ad 100644
--- a/arch/arm64/boot/dts/broadcom/Makefile
+++ b/arch/arm64/boot/dts/broadcom/Makefile
@@ -6,6 +6,7 @@ DTC_FLAGS := -@
dtb-$(CONFIG_ARCH_BCM2835) += bcm2711-rpi-400.dtb \
bcm2711-rpi-4-b.dtb \
bcm2711-rpi-cm4-io.dtb \
+ bcm2712-rpi-5-b.dtb \
bcm2837-rpi-3-a-plus.dtb \
bcm2837-rpi-3-b.dtb \
bcm2837-rpi-3-b-plus.dtb \
diff --git a/arch/arm64/boot/dts/broadcom/bcm2712-rpi-5-b.dts b/arch/arm64/boot/dts/broadcom/bcm2712-rpi-5-b.dts
new file mode 100644
index 000000000000..2bdbb6780242
--- /dev/null
+++ b/arch/arm64/boot/dts/broadcom/bcm2712-rpi-5-b.dts
@@ -0,0 +1,64 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include "bcm2712.dtsi"
+
+/ {
+ compatible = "raspberrypi,5-model-b", "brcm,bcm2712";
+ model = "Raspberry Pi 5";
+
+ aliases {
+ serial10 = &uart10;
+ };
+
+ chosen: chosen {
+ stdout-path = "serial10:115200n8";
+ };
+
+ /* Will be filled by the bootloader */
+ memory@0 {
+ device_type = "memory";
+ reg = <0 0 0 0x28000000>;
+ };
+
+ sd_io_1v8_reg: sd-io-1v8-reg {
+ compatible = "regulator-gpio";
+ regulator-name = "vdd-sd-io";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ regulator-settling-time-us = <5000>;
+ gpios = <&gio_aon 3 GPIO_ACTIVE_HIGH>;
+ states = <1800000 1>,
+ <3300000 0>;
+ };
+
+ sd_vcc_reg: sd-vcc-reg {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc-sd";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ enable-active-high;
+ gpios = <&gio_aon 4 GPIO_ACTIVE_HIGH>;
+ };
+};
+
+/* The Debug UART, on Rpi5 it's on JST-SH 1.0mm 3-pin connector
+ * labeled "UART", i.e. the interface with the system console.
+ */
+&uart10 {
+ status = "okay";
+};
+
+/* SDIO1 is used to drive the SD card */
+&sdio1 {
+ vqmmc-supply = <&sd_io_1v8_reg>;
+ vmmc-supply = <&sd_vcc_reg>;
+ bus-width = <4>;
+ sd-uhs-sdr50;
+ sd-uhs-ddr50;
+ sd-uhs-sdr104;
+};
diff --git a/arch/arm64/boot/dts/broadcom/bcm2712.dtsi b/arch/arm64/boot/dts/broadcom/bcm2712.dtsi
new file mode 100644
index 000000000000..71b0fa6c9594
--- /dev/null
+++ b/arch/arm64/boot/dts/broadcom/bcm2712.dtsi
@@ -0,0 +1,292 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+
+/ {
+ compatible = "brcm,bcm2712";
+
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ interrupt-parent = <&gicv2>;
+
+ axi: axi@1000000000 {
+ compatible = "simple-bus";
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges = <0x10 0x00000000 0x10 0x00000000 0x01 0x00000000>;
+
+ sdio1: mmc@1000fff000 {
+ compatible = "brcm,bcm2712-sdhci",
+ "brcm,sdhci-brcmstb";
+ reg = <0x10 0x00fff000 0x0 0x260>,
+ <0x10 0x00fff400 0x0 0x200>;
+ reg-names = "host", "cfg";
+ interrupts = <GIC_SPI 273 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clk_emmc2>;
+ clock-names = "sw_sdio";
+ mmc-ddr-3_3v;
+ };
+
+ gicv2: interrupt-controller@107fff9000 {
+ interrupt-controller;
+ #interrupt-cells = <3>;
+ compatible = "arm,gic-400";
+ reg = <0x10 0x7fff9000 0x0 0x1000>,
+ <0x10 0x7fffa000 0x0 0x2000>,
+ <0x10 0x7fffc000 0x0 0x2000>,
+ <0x10 0x7fffe000 0x0 0x2000>;
Please move compatible and reg before the other properties (DTS coding
style)
+ };
+ };
+
+ clocks {
+ /* The oscillator is the root of the clock tree. */
+ clk_osc: clk-osc {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-output-names = "osc";
+ clock-frequency = <54000000>;
+ };
+
+ clk_vpu: clk-vpu {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <750000000>;
+ clock-output-names = "vpu-clock";
+ };
Is the VPU clock really fixed or is it just a workaround for minimal
boot support?
Except of this, LGTM
