From: Christophe Kerello <christophe.kerello@xxxxxxxxxxx>
Add the support of SDIO in-band interrupt mode for STM32 and Ux500
variants.
It allows the SD I/O card to interrupt the host on SDMMC_D1 data line.
It is not enabled by default on Ux500 variant as this is unstable and
Ux500 users should use out-of-band IRQs.
Signed-off-by: Christophe Kerello <christophe.kerello@xxxxxxxxxxx>
Signed-off-by: Yann Gautier <yann.gautier@xxxxxxxxxxx>
---
Updates on v3:
* remove variant ops enable_sdio_irq & sdio_irq and use common
functions (mmci_write_sdio_irq_bit() & mmci_signal_sdio_irq())
* enable datactrl_mask_sdio during probe if relevant and keep it
enabled in mmci_write_datactrlreg().
Updates on v2:
* rename use_sdio_irq to supports_sdio_irq and change it to bool
* use common code for ux500 and stm32 variants
---
drivers/mmc/host/mmci.c | 69 +++++++++++++++++++++++++++++++++++++++--
drivers/mmc/host/mmci.h | 2 ++
2 files changed, 69 insertions(+), 2 deletions(-)
diff --git a/drivers/mmc/host/mmci.c b/drivers/mmc/host/mmci.c
index e967cca7a16f..b790c3c3c8f9 100644
--- a/drivers/mmc/host/mmci.c
+++ b/drivers/mmc/host/mmci.c
@@ -273,6 +273,7 @@ static struct variant_data variant_stm32_sdmmc = {
.datactrl_mask_sdio = MCI_DPSM_ST_SDIOEN,
.stm32_idmabsize_mask = GENMASK(12, 5),
.stm32_idmabsize_align = BIT(5),
+ .supports_sdio_irq = true,
.busy_timeout = true,
.busy_detect = true,
.busy_detect_flag = MCI_STM32_BUSYD0,
@@ -300,6 +301,7 @@ static struct variant_data variant_stm32_sdmmcv2 = {
.datactrl_mask_sdio = MCI_DPSM_ST_SDIOEN,
.stm32_idmabsize_mask = GENMASK(16, 5),
.stm32_idmabsize_align = BIT(5),
+ .supports_sdio_irq = true,
.dma_lli = true,
.busy_timeout = true,
.busy_detect = true,
@@ -328,6 +330,7 @@ static struct variant_data variant_stm32_sdmmcv3 = {
.datactrl_mask_sdio = MCI_DPSM_ST_SDIOEN,
.stm32_idmabsize_mask = GENMASK(16, 6),
.stm32_idmabsize_align = BIT(6),
+ .supports_sdio_irq = true,
.dma_lli = true,
.busy_timeout = true,
.busy_detect = true,
@@ -421,8 +424,9 @@ void mmci_write_pwrreg(struct mmci_host *host, u32 pwr)
*/
static void mmci_write_datactrlreg(struct mmci_host *host, u32 datactrl)
{
- /* Keep busy mode in DPSM if enabled */
- datactrl |= host->datactrl_reg & host->variant->busy_dpsm_flag;
+ /* Keep busy mode in DPSM and SDIO mask if enabled */
+ datactrl |= host->datactrl_reg & (host->variant->busy_dpsm_flag |
+ host->variant->datactrl_mask_sdio);
if (host->datactrl_reg != datactrl) {
host->datactrl_reg = datactrl;
@@ -1762,6 +1766,25 @@ static irqreturn_t mmci_pio_irq(int irq, void *dev_id)
return IRQ_HANDLED;
}
+static void mmci_write_sdio_irq_bit(struct mmci_host *host, int enable)
+{
+ void __iomem *base = host->base;
+ u32 mask = readl_relaxed(base + MMCIMASK0);
+
+ if (enable)
+ writel_relaxed(mask | MCI_ST_SDIOITMASK, base + MMCIMASK0);
+ else
+ writel_relaxed(mask & ~MCI_ST_SDIOITMASK, base + MMCIMASK0);
+}
+
+static void mmci_signal_sdio_irq(struct mmci_host *host, u32 status)
+{
+ if (status & MCI_ST_SDIOIT) {
+ mmci_write_sdio_irq_bit(host, 0);
+ sdio_signal_irq(host->mmc);
+ }
+}
+
/*
* Handle completion of command and data transfers.
*/
@@ -1806,6 +1829,9 @@ static irqreturn_t mmci_irq(int irq, void *dev_id)
mmci_data_irq(host, host->data, status);
}
+ if (host->variant->supports_sdio_irq)
+ mmci_signal_sdio_irq(host, status);
+
/*
* Busy detection has been handled by mmci_cmd_irq() above.
* Clear the status bit to prevent polling in IRQ context.
@@ -2042,6 +2068,35 @@ static int mmci_sig_volt_switch(struct mmc_host *mmc, struct mmc_ios *ios)
return ret;
}
+static void mmci_enable_sdio_irq(struct mmc_host *mmc, int enable)
+{
+ struct mmci_host *host = mmc_priv(mmc);
+ unsigned long flags;
+
+ if (enable)
+ /* Keep the SDIO mode bit if SDIO irqs are enabled */
+ pm_runtime_get_sync(mmc_dev(mmc));
+
+ spin_lock_irqsave(&host->lock, flags);
+ mmci_write_sdio_irq_bit(host, enable);
+ spin_unlock_irqrestore(&host->lock, flags);
+
+ if (!enable) {
+ pm_runtime_mark_last_busy(mmc_dev(mmc));
+ pm_runtime_put_autosuspend(mmc_dev(mmc));
+ }
+}
+
+static void mmci_ack_sdio_irq(struct mmc_host *mmc)
+{
+ struct mmci_host *host = mmc_priv(mmc);
+ unsigned long flags;
+
+ spin_lock_irqsave(&host->lock, flags);
+ mmci_write_sdio_irq_bit(host, 1);
+ spin_unlock_irqrestore(&host->lock, flags);
+}
+
static struct mmc_host_ops mmci_ops = {
.request = mmci_request,
.pre_req = mmci_pre_request,
@@ -2317,6 +2372,16 @@ static int mmci_probe(struct amba_device *dev,
mmc->caps |= MMC_CAP_WAIT_WHILE_BUSY;
}
+ if (variant->supports_sdio_irq && host->mmc->caps & MMC_CAP_SDIO_IRQ) {
+ mmc->caps2 |= MMC_CAP2_SDIO_IRQ_NOTHREAD;
+
+ mmci_ops.enable_sdio_irq = mmci_enable_sdio_irq;
+ mmci_ops.ack_sdio_irq = mmci_ack_sdio_irq;
+
+ mmci_write_datactrlreg(host,
+ host->variant->datactrl_mask_sdio);
+ }
+
/* Variants with mandatory busy timeout in HW needs R1B responses. */
if (variant->busy_timeout)
mmc->caps |= MMC_CAP_NEED_RSP_BUSY;
diff --git a/drivers/mmc/host/mmci.h b/drivers/mmc/host/mmci.h
index 34d9897c289b..a5eb4ced4d5d 100644
--- a/drivers/mmc/host/mmci.h
+++ b/drivers/mmc/host/mmci.h
@@ -331,6 +331,7 @@ enum mmci_busy_state {
* register.
* @opendrain: bitmask identifying the OPENDRAIN bit inside MMCIPOWER register
* @dma_lli: true if variant has dma link list feature.
+ * @supports_sdio_irq: allow SD I/O card to interrupt the host
* @stm32_idmabsize_mask: stm32 sdmmc idma buffer size.
* @dma_flow_controller: use peripheral as flow controller for DMA.
*/
@@ -377,6 +378,7 @@ struct variant_data {
u32 start_err;
u32 opendrain;
u8 dma_lli:1;
+ bool supports_sdio_irq;
u32 stm32_idmabsize_mask;
u32 stm32_idmabsize_align;
bool dma_flow_controller;
--
2.34.1
