Re: [PATCH 3/6] mmc: sdhci-of-dwcmshc: Add support for T-Head TH1520

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Thu, Sep 21, 2023 at 06:49:50PM -0700, Drew Fustini wrote:
> Add support for the mmc controller in the T-Head TH1520 with the new
> compatible "thead,th1520-dwcmshc". Implement custom sdhci_ops for
> set_uhs_signaling, reset, voltage_switch, and platform_execute_tuning.
> 
> Signed-off-by: Drew Fustini <dfustini@xxxxxxxxxxxx>

Hi Drew,
Thanks for doing this and sorry for being late for this code review. Some
comments below.

> ---
>  drivers/mmc/host/sdhci-of-dwcmshc.c | 456 ++++++++++++++++++++++++++++++++++++
>  1 file changed, 456 insertions(+)
> 
> diff --git a/drivers/mmc/host/sdhci-of-dwcmshc.c b/drivers/mmc/host/sdhci-of-dwcmshc.c
> index 3a3bae6948a8..7294bf1afb7d 100644
> --- a/drivers/mmc/host/sdhci-of-dwcmshc.c
> +++ b/drivers/mmc/host/sdhci-of-dwcmshc.c
> @@ -35,6 +35,26 @@
>  #define DWCMSHC_CARD_IS_EMMC		BIT(0)
>  #define DWCMSHC_ENHANCED_STROBE		BIT(8)
>  #define DWCMSHC_EMMC_ATCTRL		0x40
> +/* Tuning and auto-tuning fields in AT_CTRL_R control register */
> +#define AT_CTRL_AT_EN			0x1 /* autotuning is enabled */
> +#define AT_CTRL_CI_SEL_SHIFT		0x1 /* bit 1 */
> +#define AT_CTRL_CI_SEL			0x1 /* interval to drive center phase select */
> +#define AT_CTRL_SWIN_TH_EN_SHIFT	0x2 /* bit 2 */
> +#define AT_CTRL_SWIN_TH_EN		0x1 /* sampling window threshold enable */
> +#define AT_CTRL_RPT_TUNE_ERR_SHIFT	0x3 /* bit 3 */
> +#define AT_CTRL_RPT_TUNE_ERR		0x1 /* enable reporting framing errors */
> +#define AT_CTRL_SW_TUNE_EN_SHIFT	0x4 /* bit 4 */
> +#define AT_CTRL_SW_TUNE_EN		0x1 /* enable software managed tuning */
> +#define AT_CTRL_WIN_EDGE_SEL_SHIFT	0x8 /* bits [11:8] */
> +#define AT_CTRL_WIN_EDGE_SEL		0xf /* sampling window edge select */
> +#define AT_CTRL_TUNE_CLK_STOP_EN_SHIFT	0x10 /* bit 16 */
> +#define AT_CTRL_TUNE_CLK_STOP_EN	0x1  /* clocks stopped during phase code change */
> +#define AT_CTRL_PRE_CHANGE_DLY_SHIFT	0x11 /* bits [18:17] */
> +#define AT_CTRL_PRE_CHANGE_DLY		0x1  /* 2-cycle latency */
> +#define AT_CTRL_POST_CHANGE_DLY_SHIFT	0x13 /* bits [20:19] */
> +#define AT_CTRL_POST_CHANGE_DLY		0x3  /* 4-cycle latency */
> +#define AT_CTRL_SWIN_TH_VAL_SHIFT	0x18 /* bits [31:24] */
> +#define AT_CTRL_SWIN_TH_VAL		0x9  /* sampling window threshold */
>  
>  /* Rockchip specific Registers */
>  #define DWCMSHC_EMMC_DLL_CTRL		0x800
> @@ -72,6 +92,84 @@
>  	(((x) & DWCMSHC_EMMC_DLL_TIMEOUT) == 0))
>  #define RK35xx_MAX_CLKS 3
>  
> +/* PHY register area pointer */
> +#define DWC_MSHC_PTR_PHY_R	0x300
> +
> +/* PHY general configuration */
> +#define PHY_CNFG_R		(DWC_MSHC_PTR_PHY_R + 0x00)
> +#define PHY_CNFG_RSTN_DEASSERT	0x1  /* Deassert PHY reset */
> +#define PHY_CNFG_PAD_SP_SHIFT	0x10 /* bits [16:9] */
> +#define PHY_CNFG_PAD_SP_VALUE	0x0c /* PMOS TX drive strength */
> +#define PHY_CNFG_PAD_SN_SHIFT	0x14 /* bits [23:20] */
> +#define PHY_CNFG_PAD_SN_VALUE	0x0c /* NMOS TX drive strength */
> +
> +/* PHY command/response pad settings */
> +#define PHY_CMDPAD_CNFG_R	(DWC_MSHC_PTR_PHY_R + 0x04)
> +
> +/* PHY data pad settings */
> +#define PHY_DATAPAD_CNFG_R	(DWC_MSHC_PTR_PHY_R + 0x06)
> +
> +/* PHY clock pad settings */
> +#define PHY_CLKPAD_CNFG_R	(DWC_MSHC_PTR_PHY_R + 0x08)
> +
> +/* PHY strobe pad settings */
> +#define PHY_STBPAD_CNFG_R	(DWC_MSHC_PTR_PHY_R + 0x0a)
> +
> +/* PHY reset pad settings */
> +#define PHY_RSTNPAD_CNFG_R	(DWC_MSHC_PTR_PHY_R + 0x0c)
> +
> +/* Bitfields are common for all pad settings */
> +#define PHY_PAD_RXSEL_1V8		0x1 /* Receiver type select for 1.8V */
> +#define PHY_PAD_RXSEL_3V3		0x2 /* Receiver type select for 3.3V */
> +
> +#define PHY_PAD_WEAKPULL_SHIFT		0x3 /* bits [4:3] */
> +#define PHY_PAD_WEAKPULL_PULLUP		0x1 /* Weak pull down enabled */
> +#define PHY_PAD_WEAKPULL_PULLDOWN	0x2 /* Weak pull down enabled */
> +
> +#define PHY_PAD_TXSLEW_CTRL_P_SHIFT	0x5 /* bits [8:5] */
> +#define PHY_PAD_TXSLEW_CTRL_P_VALUE	0x3 /* Slew control for P-Type pad TX */
> +#define PHY_PAD_TXSLEW_CTRL_N_SHIFT	0x9 /* bits [12:9] */
> +#define PHY_PAD_TXSLEW_CTRL_N_VALUE	0x3 /* Slew control for N-Type pad TX */
> +
> +/* PHY CLK delay line settings */
> +#define PHY_SDCLKDL_CNFG_R		(DWC_MSHC_PTR_PHY_R + 0x1d)
> +#define PHY_SDCLKDL_CNFG_UPDATE_SHIFT	0x4 /* bit 4 */
> +#define PHY_SDCLKDL_CNFG_UPDATE_DC	0x1 /* set before writing to SDCLKDL_DC */
> +
> +/* PHY CLK delay line delay code */
> +#define PHY_SDCLKDL_DC_R		(DWC_MSHC_PTR_PHY_R + 0x1e)
> +#define PHY_SDCLKDL_DC_INITIAL		0x40 /* initial delay code */
> +#define PHY_SDCLKDL_DC_DEFAULT		0x32 /* default delay code */
> +#define PHY_SDCLKDL_DC_HS400		0x18 /* delay code for HS400 mode */
> +
> +/* PHY drift_cclk_rx delay line configuration setting */
> +#define PHY_ATDL_CNFG_R			(DWC_MSHC_PTR_PHY_R + 0x21)
> +#define PHY_ATDL_CNFG_INPSEL_SHIFT	0x2 /* bits [3:2] */
> +#define PHY_ATDL_CNFG_INPSEL_VALUE	0x3 /* delay line input source */
> +
> +/* PHY DLL control settings */
> +#define PHY_DLL_CTRL_R			(DWC_MSHC_PTR_PHY_R + 0x24)
> +#define PHY_DLL_CTRL_DISABLE		0x0 /* PHY DLL is enabled */
> +#define PHY_DLL_CTRL_ENABLE		0x1 /* PHY DLL is disabled */
> +
> +/* PHY DLL  configuration register 1 */
> +#define PHY_DLL_CNFG1_R			(DWC_MSHC_PTR_PHY_R + 0x25)
> +#define PHY_DLL_CNFG1_SLVDLY_SHIFT	0x4 /* bits [5:4] */
> +#define PHY_DLL_CNFG1_SLVDLY_VALUE	0x2 /* DLL slave update delay input */
> +#define PHY_DLL_CNFG1_WAITCYCLE		0x5 /* DLL wait cycle input */
> +
> +/* PHY DLL configuration register 2 */
> +#define PHY_DLL_CNFG2_R			(DWC_MSHC_PTR_PHY_R + 0x26)
> +#define PHY_DLL_CNFG2_JUMPSTEP		0xa /* DLL jump step input */
> +
> +/* PHY DLL master and slave delay line configuration settings */
> +#define PHY_DLLDL_CNFG_R		(DWC_MSHC_PTR_PHY_R + 0x28)
> +#define PHY_DLLDL_CNFG_SLV_INPSEL_SHIFT	0x5 /* bits [6:5] */
> +#define PHY_DLLDL_CNFG_SLV_INPSEL_VALUE	0x3 /* clock source select for slave DL */
> +
> +#define FLAG_PULL_UP_EN		BIT(0)
> +#define FLAG_IO_FIXED_1V8	BIT(1)
> +
>  #define BOUNDARY_OK(addr, len) \
>  	((addr | (SZ_128M - 1)) == ((addr + len - 1) | (SZ_128M - 1)))
>  
> @@ -92,6 +190,8 @@ struct dwcmshc_priv {
>  	struct clk	*bus_clk;
>  	int vendor_specific_area1; /* P_VENDOR_SPECIFIC_AREA reg */
>  	void *priv; /* pointer to SoC private stuff */
> +	u16 delay_line;
> +	u16 flags;
>  };
>  
>  /*
> @@ -157,6 +257,206 @@ static void dwcmshc_request(struct mmc_host *mmc, struct mmc_request *mrq)
>  	sdhci_request(mmc, mrq);
>  }
>  
> +static void th1520_phy_1_8v_init_no_pull(struct sdhci_host *host)
> +{
> +	u32 val;
> +
> +	/* deassert phy reset */
> +	sdhci_writel(host, PHY_CNFG_RSTN_DEASSERT, PHY_CNFG_R);
> +
> +	/* disable delay line */
> +	sdhci_writeb(host, PHY_SDCLKDL_CNFG_UPDATE_DC << PHY_SDCLKDL_CNFG_UPDATE_SHIFT,
> +		     PHY_SDCLKDL_CNFG_R);
> +
> +	/* set delay line */
> +	sdhci_writeb(host, PHY_SDCLKDL_DC_INITIAL, PHY_SDCLKDL_DC_R);
> +
> +	/* enable delay lane */
> +	val = sdhci_readb(host, PHY_SDCLKDL_CNFG_R);
> +	val &= ~(PHY_SDCLKDL_CNFG_UPDATE_DC << PHY_SDCLKDL_CNFG_UPDATE_SHIFT);
> +	sdhci_writeb(host, val, PHY_SDCLKDL_CNFG_R);
> +
> +	/* configure phy pads */
> +	val = sdhci_readw(host, PHY_CMDPAD_CNFG_R);
> +	sdhci_writew(host, val | PHY_PAD_RXSEL_1V8, PHY_CMDPAD_CNFG_R);
> +
> +	val = sdhci_readw(host, PHY_DATAPAD_CNFG_R);
> +	sdhci_writew(host, val | PHY_PAD_RXSEL_1V8, PHY_DATAPAD_CNFG_R);
> +
> +	val = sdhci_readw(host, PHY_RSTNPAD_CNFG_R);
> +	sdhci_writew(host, val | PHY_PAD_RXSEL_1V8, PHY_RSTNPAD_CNFG_R);
> +
> +	val = sdhci_readw(host, PHY_STBPAD_CNFG_R);
> +	sdhci_writew(host, val | PHY_PAD_RXSEL_1V8, PHY_STBPAD_CNFG_R);
> +
> +	/* enable phy dll */
> +	val = sdhci_readb(host, PHY_DLL_CTRL_R);
> +	sdhci_writeb(host, val | PHY_DLL_CTRL_ENABLE, PHY_DLL_CTRL_R);
> +}
> +
> +static void th1520_phy_3_3v_init_no_pull(struct sdhci_host *host)
> +{
> +	u32 val;
> +
> +	/* deassert phy reset */
> +	sdhci_writel(host, PHY_CNFG_RSTN_DEASSERT, PHY_CNFG_R);
> +
> +	/* disable delay line */
> +	sdhci_writeb(host, PHY_SDCLKDL_CNFG_UPDATE_DC << PHY_SDCLKDL_CNFG_UPDATE_SHIFT,
> +		     PHY_SDCLKDL_CNFG_R);
> +
> +	/* set delay line */
> +	sdhci_writeb(host, PHY_SDCLKDL_DC_INITIAL, PHY_SDCLKDL_DC_R);
> +
> +	/* enable delay lane */
> +	val = sdhci_readb(host, PHY_SDCLKDL_CNFG_R);
> +	val &= ~(PHY_SDCLKDL_CNFG_UPDATE_DC << PHY_SDCLKDL_CNFG_UPDATE_SHIFT);
> +	sdhci_writeb(host, val, PHY_SDCLKDL_CNFG_R);
> +
> +	/* configure phy pads */
> +	val = sdhci_readw(host, PHY_CMDPAD_CNFG_R);
> +	sdhci_writew(host, val | PHY_PAD_RXSEL_3V3, PHY_CMDPAD_CNFG_R);
> +
> +	val = sdhci_readw(host, PHY_DATAPAD_CNFG_R);
> +	sdhci_writew(host, val | PHY_PAD_RXSEL_3V3, PHY_DATAPAD_CNFG_R);
> +
> +	val = sdhci_readw(host, PHY_RSTNPAD_CNFG_R);
> +	sdhci_writew(host, val | PHY_PAD_RXSEL_3V3, PHY_RSTNPAD_CNFG_R);
> +
> +	val = sdhci_readw(host, PHY_STBPAD_CNFG_R);
> +	sdhci_writew(host, val | PHY_PAD_RXSEL_3V3, PHY_STBPAD_CNFG_R);
> +
> +	/* enable phy dll */
> +	val = sdhci_readb(host, PHY_DLL_CTRL_R);
> +	sdhci_writeb(host, val | PHY_DLL_CTRL_ENABLE, PHY_DLL_CTRL_R);
> +}
> +
> +static void th1520_phy_1_8v_init(struct sdhci_host *host)
> +{
> +	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
> +	struct dwcmshc_priv *priv = sdhci_pltfm_priv(pltfm_host);
> +	u32 val;
> +
> +	if (!priv)
> +		return;
> +
> +	if (!(priv->flags & FLAG_PULL_UP_EN)) {
> +		th1520_phy_1_8v_init_no_pull(host);
> +		return;
> +	}
> +
> +	/* deassert phy reset & set tx drive strength */
> +	sdhci_writel(host, PHY_CNFG_RSTN_DEASSERT |
> +		    (PHY_CNFG_PAD_SP_VALUE << PHY_CNFG_PAD_SP_SHIFT) |
> +		    (PHY_CNFG_PAD_SN_VALUE << PHY_CNFG_PAD_SN_SHIFT),
> +		    PHY_CNFG_R);
> +
> +	/* disable delay line */
> +	sdhci_writeb(host, PHY_SDCLKDL_CNFG_UPDATE_DC << PHY_SDCLKDL_CNFG_UPDATE_SHIFT,
> +		     PHY_SDCLKDL_CNFG_R);
> +
> +	/* set delay line */
> +	sdhci_writeb(host, priv->delay_line, PHY_SDCLKDL_DC_R);
> +	sdhci_writeb(host, PHY_DLL_CNFG2_JUMPSTEP, PHY_DLL_CNFG2_R);
> +
> +	/* enable delay lane */
> +	val = sdhci_readb(host, PHY_SDCLKDL_CNFG_R);
> +	val &= ~(PHY_SDCLKDL_CNFG_UPDATE_DC << PHY_SDCLKDL_CNFG_UPDATE_SHIFT);
> +	sdhci_writeb(host, val, PHY_SDCLKDL_CNFG_R);
> +
> +	/* configure phy pads */
> +	val = PHY_PAD_RXSEL_1V8 | (PHY_PAD_WEAKPULL_PULLUP << PHY_PAD_WEAKPULL_SHIFT) |
> +	      (PHY_PAD_TXSLEW_CTRL_P_VALUE << PHY_PAD_TXSLEW_CTRL_P_SHIFT) |
> +	      (PHY_PAD_TXSLEW_CTRL_N_VALUE << PHY_PAD_TXSLEW_CTRL_N_SHIFT);
> +	sdhci_writew(host, val, PHY_CMDPAD_CNFG_R);
> +	sdhci_writew(host, val, PHY_DATAPAD_CNFG_R);
> +	sdhci_writew(host, val, PHY_RSTNPAD_CNFG_R);
> +
> +	val = (PHY_PAD_TXSLEW_CTRL_P_VALUE << PHY_PAD_TXSLEW_CTRL_P_SHIFT) |
> +	      (PHY_PAD_TXSLEW_CTRL_N_VALUE << PHY_PAD_TXSLEW_CTRL_N_SHIFT);
> +	sdhci_writew(host, val, PHY_CLKPAD_CNFG_R);
> +
> +	val = PHY_PAD_RXSEL_1V8 | (PHY_PAD_WEAKPULL_PULLDOWN << PHY_PAD_WEAKPULL_SHIFT) |
> +	      (PHY_PAD_TXSLEW_CTRL_P_VALUE << PHY_PAD_TXSLEW_CTRL_P_SHIFT) |
> +	      (PHY_PAD_TXSLEW_CTRL_N_VALUE << PHY_PAD_TXSLEW_CTRL_N_SHIFT);
> +	sdhci_writew(host, val, PHY_STBPAD_CNFG_R);
> +
> +	/* enable data strobe mode */
> +	sdhci_writeb(host, PHY_DLLDL_CNFG_SLV_INPSEL_VALUE << PHY_DLLDL_CNFG_SLV_INPSEL_SHIFT,
> +		     PHY_DLLDL_CNFG_R);
> +
> +	/* enable phy dll */
> +	sdhci_writeb(host, PHY_DLL_CTRL_ENABLE,  PHY_DLL_CTRL_R);
> +}
> +
> +static void th1520_phy_3_3v_init(struct sdhci_host *host)
> +{
> +	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
> +	struct dwcmshc_priv *priv = sdhci_pltfm_priv(pltfm_host);
> +	u32 val;
> +
> +	if (!(priv->flags & FLAG_PULL_UP_EN)) {
> +		th1520_phy_3_3v_init_no_pull(host);
> +		return;
> +	}
> +
> +	/* deassert phy reset & set tx drive strength */
> +	sdhci_writel(host, PHY_CNFG_RSTN_DEASSERT |
> +		    (PHY_CNFG_PAD_SP_VALUE << PHY_CNFG_PAD_SP_SHIFT) |
> +		    (PHY_CNFG_PAD_SN_VALUE << PHY_CNFG_PAD_SN_SHIFT),
> +		    PHY_CNFG_R);
> +
> +	/* disable delay line */
> +	sdhci_writeb(host, PHY_SDCLKDL_CNFG_UPDATE_DC << PHY_SDCLKDL_CNFG_UPDATE_SHIFT,
> +		     PHY_SDCLKDL_CNFG_R);
> +
> +	/* set delay line */
> +	sdhci_writeb(host, priv->delay_line, PHY_SDCLKDL_DC_R);
> +	sdhci_writeb(host, PHY_DLL_CNFG2_JUMPSTEP, PHY_DLL_CNFG2_R);
> +
> +	/* enable delay lane */
> +	val = sdhci_readb(host, PHY_SDCLKDL_CNFG_R);
> +	val &= ~(PHY_SDCLKDL_CNFG_UPDATE_DC << PHY_SDCLKDL_CNFG_UPDATE_SHIFT);
> +	sdhci_writeb(host, val, PHY_SDCLKDL_CNFG_R);
> +
> +	/* configure phy pads */
> +	val = PHY_PAD_RXSEL_3V3 | (PHY_PAD_WEAKPULL_PULLUP << PHY_PAD_WEAKPULL_SHIFT) |
> +	      (PHY_PAD_TXSLEW_CTRL_P_VALUE << PHY_PAD_TXSLEW_CTRL_P_SHIFT) |
> +	      (PHY_PAD_TXSLEW_CTRL_N_VALUE << PHY_PAD_TXSLEW_CTRL_N_SHIFT);
> +	sdhci_writew(host, val, PHY_CMDPAD_CNFG_R);
> +	sdhci_writew(host, val, PHY_DATAPAD_CNFG_R);
> +	sdhci_writew(host, val, PHY_RSTNPAD_CNFG_R);
> +
> +	val = (PHY_PAD_TXSLEW_CTRL_P_VALUE << PHY_PAD_TXSLEW_CTRL_P_SHIFT) |
> +	      (PHY_PAD_TXSLEW_CTRL_N_VALUE << PHY_PAD_TXSLEW_CTRL_N_SHIFT);
> +	sdhci_writew(host, val, PHY_CLKPAD_CNFG_R);
> +
> +	val = PHY_PAD_RXSEL_3V3 | (PHY_PAD_WEAKPULL_PULLDOWN << PHY_PAD_WEAKPULL_SHIFT) |
> +	      (PHY_PAD_TXSLEW_CTRL_P_VALUE << PHY_PAD_TXSLEW_CTRL_P_SHIFT) |
> +	      (PHY_PAD_TXSLEW_CTRL_N_VALUE << PHY_PAD_TXSLEW_CTRL_N_SHIFT);
> +	sdhci_writew(host, val, PHY_STBPAD_CNFG_R);
> +}
> +
> +static void th1520_sdhci_set_phy(struct sdhci_host *host)
> +{
> +	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
> +	struct dwcmshc_priv *priv = sdhci_pltfm_priv(pltfm_host);
> +	u16 emmc_ctrl;
> +
> +	/* Before power on, set PHY configs */
> +	if (host->mmc->caps & MMC_CAP_NONREMOVABLE) {

check flag & FLAG_IO_FIXED_1V8 instead? Because I didn't see why
3.3v can't be non-removeable. I know you only brought up emmc
now, but we can also prepare for sdio/sd support at the same time.

> +		th1520_phy_1_8v_init(host);
> +		emmc_ctrl = sdhci_readw(host, priv->vendor_specific_area1 + DWCMSHC_EMMC_CONTROL);
> +		emmc_ctrl |= DWCMSHC_CARD_IS_EMMC;

can we check host->mmc->caps2 to know whether this is eMMC or not, then
set this bit for eMMC after that.

And setting DWCMSHC_CARD_IS_EMMC should be orthogonalized with 3.3v/1.8v
etc.

> +		sdhci_writew(host, emmc_ctrl, priv->vendor_specific_area1 + DWCMSHC_EMMC_CONTROL);
> +	} else {
> +		th1520_phy_3_3v_init(host);

> +	}
> +
> +	sdhci_writeb(host, (PHY_DLL_CNFG1_SLVDLY_VALUE << PHY_DLL_CNFG1_SLVDLY_SHIFT) |

I'm not sure whether we need to get the delay value from DT.
Do emmc, sd and sdio share the same delay value?

> +		     PHY_DLL_CNFG1_WAITCYCLE, PHY_DLL_CNFG1_R);
> +}
> +
>  static void dwcmshc_set_uhs_signaling(struct sdhci_host *host,
>  				      unsigned int timing)
>  {
> @@ -189,9 +489,30 @@ static void dwcmshc_set_uhs_signaling(struct sdhci_host *host,
>  		ctrl_2 |= DWCMSHC_CTRL_HS400;
>  	}
>  
> +	if (priv->flags & FLAG_IO_FIXED_1V8)
> +		ctrl_2 |= SDHCI_CTRL_VDD_180;
>  	sdhci_writew(host, ctrl_2, SDHCI_HOST_CONTROL2);
>  }
>  
> +static void th1520_set_uhs_signaling(struct sdhci_host *host,
> +				     unsigned int timing)
> +{
> +	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
> +	struct dwcmshc_priv *priv = sdhci_pltfm_priv(pltfm_host);
> +	u32 reg;
> +
> +	dwcmshc_set_uhs_signaling(host, timing);
> +	if (timing == MMC_TIMING_MMC_HS400) {
> +		reg = sdhci_readl(host, priv->vendor_specific_area1 + DWCMSHC_EMMC_ATCTRL);
> +		reg &= ~AT_CTRL_AT_EN;
> +		sdhci_writel(host, reg, priv->vendor_specific_area1 + DWCMSHC_EMMC_ATCTRL);

can we move the auto tuning bit setting to tuning routine?

> +		priv->delay_line = PHY_SDCLKDL_DC_HS400;

this delay line may need to be gotten from DT?

> +		th1520_sdhci_set_phy(host);
> +	} else {
> +		sdhci_writeb(host, 0, PHY_DLLDL_CNFG_R);
> +	}
> +}
> +
>  static void dwcmshc_hs400_enhanced_strobe(struct mmc_host *mmc,
>  					  struct mmc_ios *ios)
>  {
> @@ -338,6 +659,91 @@ static void rk35xx_sdhci_reset(struct sdhci_host *host, u8 mask)
>  	sdhci_reset(host, mask);
>  }
>  
> +static int th1520_execute_tuning(struct sdhci_host *host, u32 opcode)
> +{
> +	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
> +	struct dwcmshc_priv *priv = sdhci_pltfm_priv(pltfm_host);
> +	u32 val = 0;
> +
> +	if (host->flags & SDHCI_HS400_TUNING)
> +		return 0;
> +
> +	sdhci_writeb(host, PHY_ATDL_CNFG_INPSEL_VALUE << PHY_ATDL_CNFG_INPSEL_SHIFT,
> +		     PHY_ATDL_CNFG_R);
> +	val = sdhci_readl(host, priv->vendor_specific_area1 + DWCMSHC_EMMC_ATCTRL);
> +
> +	/*
> +	 * configure tuning settings:
> +	 *  - center phase select code driven in block gap interval
> +	 *  - disable reporting of framing errors
> +	 *  - disable software managed tuning
> +	 *  - disable user selection of sampling window edges,
> +	 *    instead tuning calculated edges are used
> +	 */
> +	val &= ~((AT_CTRL_CI_SEL << AT_CTRL_CI_SEL_SHIFT) |
> +		(AT_CTRL_RPT_TUNE_ERR << AT_CTRL_RPT_TUNE_ERR_SHIFT) |
> +		(AT_CTRL_SW_TUNE_EN << AT_CTRL_SW_TUNE_EN_SHIFT) |
> +		(AT_CTRL_WIN_EDGE_SEL << AT_CTRL_WIN_EDGE_SEL_SHIFT));
> +
> +	/*
> +	 * configure tuning settings:
> +	 *  - enable auto-tuning
> +	 *  - enable sampling window threshold
> +	 *  - stop clocks during phase code change
> +	 *  - set max latency in cycles between tx and rx clocks
> +	 *  - set max latency in cycles to switch output phase
> +	 *  - set max sampling window threshold value
> +	 */
> +	val |= AT_CTRL_AT_EN | (AT_CTRL_SWIN_TH_EN << AT_CTRL_SWIN_TH_EN_SHIFT) |
> +		(AT_CTRL_TUNE_CLK_STOP_EN << AT_CTRL_TUNE_CLK_STOP_EN_SHIFT) |
> +		(AT_CTRL_PRE_CHANGE_DLY << AT_CTRL_PRE_CHANGE_DLY_SHIFT) |
> +		(AT_CTRL_POST_CHANGE_DLY << AT_CTRL_POST_CHANGE_DLY_SHIFT) |
> +		(AT_CTRL_SWIN_TH_VAL << AT_CTRL_SWIN_TH_VAL_SHIFT);
> +
> +	sdhci_writel(host, val, priv->vendor_specific_area1 + DWCMSHC_EMMC_ATCTRL);
> +	val = sdhci_readl(host, priv->vendor_specific_area1 + DWCMSHC_EMMC_ATCTRL);
> +
> +	/* check if is possible to enable auto-tuning */
> +	if (!(val & AT_CTRL_AT_EN)) {
> +		dev_err(mmc_dev(host->mmc), "failed to enable auto tuning\n");
> +		return -EIO;
> +	}
> +
> +	/* disable auto tuning */
> +	val &= ~AT_CTRL_AT_EN;
> +	sdhci_writel(host, val, priv->vendor_specific_area1 + DWCMSHC_EMMC_ATCTRL);

AFAIK, the HW support auto tuning, can we enable it?

> +
> +	/* perform tuning */
> +	sdhci_start_tuning(host);
> +	host->tuning_err = __sdhci_execute_tuning(host, opcode);
> +	if (host->tuning_err) {
> +		val &= ~AT_CTRL_AT_EN;

It looks like auto tunning is never enabled, so why do clear it here?

> +		sdhci_writel(host, val, priv->vendor_specific_area1 + DWCMSHC_EMMC_ATCTRL);
> +		dev_err(mmc_dev(host->mmc), "tuning failed: %d\n", host->tuning_err);
> +		return -EIO;
> +	}
> +	sdhci_end_tuning(host);
> +
> +	return 0;
> +}
> +
> +static void th1520_sdhci_reset(struct sdhci_host *host, u8 mask)
> +{
> +	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
> +	struct dwcmshc_priv *priv = sdhci_pltfm_priv(pltfm_host);
> +	u16 ctrl_2;
> +
> +	sdhci_reset(host, mask);
> +
> +	if (priv->flags & FLAG_IO_FIXED_1V8) {
> +		ctrl_2 = sdhci_readw(host, SDHCI_HOST_CONTROL2);
> +		if (!(ctrl_2 & SDHCI_CTRL_VDD_180)) {
> +			ctrl_2 |= SDHCI_CTRL_VDD_180;
> +			sdhci_writew(host, ctrl_2, SDHCI_HOST_CONTROL2);
> +		}
> +	}
> +}
> +
>  static const struct sdhci_ops sdhci_dwcmshc_ops = {
>  	.set_clock		= sdhci_set_clock,
>  	.set_bus_width		= sdhci_set_bus_width,
> @@ -356,6 +762,17 @@ static const struct sdhci_ops sdhci_dwcmshc_rk35xx_ops = {
>  	.adma_write_desc	= dwcmshc_adma_write_desc,
>  };
>  
> +static const struct sdhci_ops sdhci_dwcmshc_th1520_ops = {
> +	.set_clock		= sdhci_set_clock,
> +	.set_bus_width		= sdhci_set_bus_width,
> +	.set_uhs_signaling	= th1520_set_uhs_signaling,
> +	.get_max_clock		= dwcmshc_get_max_clock,
> +	.reset			= th1520_sdhci_reset,
> +	.adma_write_desc	= dwcmshc_adma_write_desc,
> +	.voltage_switch		= th1520_phy_1_8v_init,
> +	.platform_execute_tuning = &th1520_execute_tuning,
> +};
> +
>  static const struct sdhci_pltfm_data sdhci_dwcmshc_pdata = {
>  	.ops = &sdhci_dwcmshc_ops,
>  	.quirks = SDHCI_QUIRK_CAP_CLOCK_BASE_BROKEN,
> @@ -379,6 +796,12 @@ static const struct sdhci_pltfm_data sdhci_dwcmshc_rk35xx_pdata = {
>  		   SDHCI_QUIRK2_CLOCK_DIV_ZERO_BROKEN,
>  };
>  
> +static const struct sdhci_pltfm_data sdhci_dwcmshc_th1520_pdata = {
> +	.ops = &sdhci_dwcmshc_th1520_ops,
> +	.quirks = SDHCI_QUIRK_CAP_CLOCK_BASE_BROKEN,
> +	.quirks2 = SDHCI_QUIRK2_PRESET_VALUE_BROKEN,
> +};
> +
>  static int dwcmshc_rk35xx_init(struct sdhci_host *host, struct dwcmshc_priv *dwc_priv)
>  {
>  	int err;
> @@ -447,6 +870,10 @@ static const struct of_device_id sdhci_dwcmshc_dt_ids[] = {
>  		.compatible = "snps,dwcmshc-sdhci",
>  		.data = &sdhci_dwcmshc_pdata,
>  	},
> +	{
> +		.compatible = "thead,th1520-dwcmshc",
> +		.data = &sdhci_dwcmshc_th1520_pdata,
> +	},
>  	{},
>  };
>  MODULE_DEVICE_TABLE(of, sdhci_dwcmshc_dt_ids);
> @@ -542,6 +969,35 @@ static int dwcmshc_probe(struct platform_device *pdev)
>  			goto err_clk;
>  	}
>  
> +	if (pltfm_data == &sdhci_dwcmshc_th1520_pdata) {
> +		priv->delay_line = PHY_SDCLKDL_DC_DEFAULT;

Ditto. 

> +
> +		if (device_property_present(&pdev->dev, "thead,phy-pull-up"))
> +			priv->flags |= FLAG_PULL_UP_EN;
> +		else
> +			priv->flags &= ~FLAG_PULL_UP_EN;
> +
> +		if ((device_property_read_bool(dev, "mmc-ddr-1_8v")) |
> +		    (device_property_read_bool(dev, "mmc-hs200-1_8v")) |
> +		    (device_property_read_bool(dev, "mmc-hs400-1_8v")))
> +			priv->flags |= FLAG_IO_FIXED_1V8;
> +		else
> +			priv->flags &= ~FLAG_IO_FIXED_1V8;
> +
> +		/*
> +		 * start_signal_voltage_switch() will try 3.3V first
> +		 * then 1.8V. Use SDHCI_SIGNALING_180 ranther than
> +		 * SDHCI_SIGNALING_330 to avoid setting voltage to 3.3V
> +		 * in sdhci_start_signal_voltage_switch().
> +		 */
> +		if (priv->flags & FLAG_IO_FIXED_1V8) {
> +			host->flags &= ~SDHCI_SIGNALING_330;
> +			host->flags |=  SDHCI_SIGNALING_180;
> +		}
> +
> +		sdhci_enable_v4_mode(host);
> +	}
> +
>  #ifdef CONFIG_ACPI
>  	if (pltfm_data == &sdhci_dwcmshc_bf3_pdata)
>  		sdhci_enable_v4_mode(host);
> 
> -- 
> 2.34.1
> 



[Index of Archives]     [Linux Memonry Technology]     [Linux USB Devel]     [Linux Media]     [Video for Linux]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]

  Powered by Linux